DIY Airband Radio Receiver Aviation Band Receiver Kit
$43.73
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Description
Like many scanner enthusiasts and ham operators, you are interested in listening in on all the excitement manifest in aeronautic communication, but lack the equipment to pursue your interest, then maybe the Aviation-Band Receiver described in this article is for you.
The Aviation Receiver, designed to tune the 118-135MHz band, features exceptional sensitivity, image rejection, signal-to-noise ratio, and stability.
The receiver is ideally suited to listening in on ground and air communication associated with commercial airlines and general aviation.
Powered from a 9-volt alkaline battery, it can be taken along with your to local airports so that you won’t miss a moment of the action.
And even if you’re nowhere near an airport, this little receiver will pick-up all the ground-to-air and vice-versa communications of any plane or ground facility within about 130 miles (190Km).
Color:Green
Material:CCL
Construction
Once you have obtained all of the components and the board for the Aviation Receiver, construction can begin. A parts-placement diagram is shown in Fig. When assembling the project, take special care that polarity-sensitive components (electrolytic capacitors [keep leads as short as possible], diodes, and transistors) are installed properly. Just one part installed backwards can cause grievous harm!
Inductors (Aircoils) L1,L3,L5 can be made easily on a 5mm drill bit. Before you wind them, scrape the enamel of each end, about 5mm. Then wind the 1.5 turn (2-turns is okay too). I know it can be tricky especially if you have big fingers like me. Begin by installing the passive components (6 jumper wires, sockets, resistors, capacitors, inductors). Followed by installing the active components; diodes, transistors, and IC’s. Once the active components have been installed, check your work for the usual construction errors; cold solder joints, misplaced or reversed-lead components, solder bridges, etc. Once you have determined that he circuit has been correctly assembled, it’s time to consider the enclosure that will house the receiver.
The receiver’s circuit board can be housed in any enclosure that you choose.
Note
Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1-3cm.
Package included
1 x DIY KITs Airband Radio Receiver Aviation Band Receiver
1 x English manual
Weight | 0.081 kg |
---|
Customers Also Viewed
LED Cool Light Egg Candler Tester Ultra Bright Pocket Poultry Egg Lamp incubator
$56.69Switch AccessoriesAdd to cartFeatures– Made of high quality ABS material, insulating, stable and durable.– LED lamp head, high power, strong light source, can clearly detect the hatching of eggs.– Using high-quality materials, safe and durable, with buttons that are easy to open and close.– Suitable for hatching eggs, but also for children and students to learn the process …
LED Cool Light Egg Candler Tester Ultra Bright Pocket Poultry Egg Lamp incubatorRead More
5pcs 2 Channel PWM Generator Module Pulse Frequency Duty Cycle Adjustable
$34.82Other Module BoardAdd to cartProduct Introduction1. Operating Voltage:5-30V,support micro USB 5.0V power supply2. Frequency Range:1Hz~150KHz3. Frequency Precision:2%4. Signal Load Capacity:output current is within 8–30mA5. Output Range:default 5V V-pp (can be changed by external power)6. Ambient Temperature:-30 Celsius ~70 Celsius Application Fields1. As square wave generator to generate square wave for experiment development2. Used to drive steeping motor driver’s square …
5pcs 2 Channel PWM Generator Module Pulse Frequency Duty Cycle AdjustableRead More
3.7V Lithium Battery 4 Paragraph Power indicator Module
$4.36Test & Measuring ModuleAdd to cartDescription1, onboard high precision voltage detection chip and power supply voltage chip2, onboard four power indicator LED lights, three kinds of color display, red, yellow, yellow, green,representing 20%, 50%, 80%, 100% of the battery3, set aside a battery testing interface and two positioning hole4, PCB size:22.2 (mm) x17.2 (mm)Package included1 x 3.7V Lithium Battery 4 …
3.7V Lithium Battery 4 Paragraph Power indicator ModuleRead More
YAHBOOM High-quality T-shape Expansion Board + 40Pin GPIO Flat Rainbow Ribbon Cable for Raspberry 4B/3B+/ZERO/W
$10.21Raspberry Pi & Orange PiAdd to cartDescriptionThis high-quality T-shape expansion board allows you to connect the Raspberry Pi GPIO port for breadboard experiments. We will provide a 40Pin soft cable for you to connect the Raspberry Pi board to the breadboard.FeaturesSpecifically designed for Raspberry Pi 4B/3B, Raspberry Pi 2B, Raspberry Pi 1B+, Raspberry pi 1A+, Raspberry Pi zero W, Raspberry Pi …
10pcs LM3915 10-segment Audio Level indicator Kit Electronic Soldering Training experiment DIY Parts
$33.89DIY Electronic KitsAdd to cartFeatrurePower supply:DC9-12VPCB size:62*27mm1 audio cable is needed. One end is subtracted and connected to the audio input port. The red cable is connected to AUDIO +, the green cable is connected to ADUIO-, and the blue cable is subtracted, do not need to solder.Package included10 x LM3915 10-segment Audio Level Indicator Kit
10pcs 40x40mm thermoelectric Power Generator Peltier Module TEG High Temperature 150 Degree
$55.12Electronic Accessories & SuppliesAdd to cartFeatureColding side posts with the wordsHeating side is emptyRed wire to positive, black wire to the negative, it generate electricity when the temperature difference happenedSpecificationModel:SP1848-27145 Color:whiteLead Length:about 30CMSize:40MM x 40MM x 3.4MM20 degree temperature difference:open-circuit voltage 0.97V, generated current:225MA40 degree temperature difference:open circuit voltage 1.8V, generated current:368MA60 degree temperature difference:open circuit voltage 2.4V, generated current:469MA80 …
10pcs 40x40mm thermoelectric Power Generator Peltier Module TEG High Temperature 150 DegreeRead More
Reviews
There are no reviews yet.