DIY Airband Radio Receiver Aviation Band Receiver Kit
$43.73
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Description
Like many scanner enthusiasts and ham operators, you are interested in listening in on all the excitement manifest in aeronautic communication, but lack the equipment to pursue your interest, then maybe the Aviation-Band Receiver described in this article is for you.
The Aviation Receiver, designed to tune the 118-135MHz band, features exceptional sensitivity, image rejection, signal-to-noise ratio, and stability.
The receiver is ideally suited to listening in on ground and air communication associated with commercial airlines and general aviation.
Powered from a 9-volt alkaline battery, it can be taken along with your to local airports so that you won’t miss a moment of the action.
And even if you’re nowhere near an airport, this little receiver will pick-up all the ground-to-air and vice-versa communications of any plane or ground facility within about 130 miles (190Km).
Color:Green
Material:CCL
Construction
Once you have obtained all of the components and the board for the Aviation Receiver, construction can begin. A parts-placement diagram is shown in Fig. When assembling the project, take special care that polarity-sensitive components (electrolytic capacitors [keep leads as short as possible], diodes, and transistors) are installed properly. Just one part installed backwards can cause grievous harm!
Inductors (Aircoils) L1,L3,L5 can be made easily on a 5mm drill bit. Before you wind them, scrape the enamel of each end, about 5mm. Then wind the 1.5 turn (2-turns is okay too). I know it can be tricky especially if you have big fingers like me. Begin by installing the passive components (6 jumper wires, sockets, resistors, capacitors, inductors). Followed by installing the active components; diodes, transistors, and IC’s. Once the active components have been installed, check your work for the usual construction errors; cold solder joints, misplaced or reversed-lead components, solder bridges, etc. Once you have determined that he circuit has been correctly assembled, it’s time to consider the enclosure that will house the receiver.
The receiver’s circuit board can be housed in any enclosure that you choose.
Note
Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1-3cm.
Package included
1 x DIY KITs Airband Radio Receiver Aviation Band Receiver
1 x English manual
Weight | 0.081 kg |
---|
Customers Also Viewed
100 Pcs Copper Cable Lugs Kit SC6-6 ~SC35-10 Electrical Terminal Block Wire Connectors
$70.86ConnectorsAdd to cartSpecificationModel:SC6-6~SC35-10Material:Tin Plated CopperColor:SilverSize:6mm²/10mm²/16mm²/25mm²/35mm²Mount Hole:6 mm/8 mm/10 mmBox Size(L*W*H):280 x 126 x 14 mmQuantity:100 PcsFeaturesElectro-plated tin exterior.Premium quality copper material, environmentally friendly, safe for using.These tube lugs have a bell shaped end allowing for easy insertion of the cable.Acceptable working temperature is -55℃ to 100℃ and are suitable for applications in the Australian Climate.Copper lugs are …
100 Pcs Copper Cable Lugs Kit SC6-6 ~SC35-10 Electrical Terminal Block Wire ConnectorsRead More
TDA7377 Subwoofer Amplifier Audio Board 38Wx3 Mini Home Amp 2.1 Channel HiFi Stereo Power Amplifier DIY
$21.86Amplifier BoardAdd to cartDescriptionThe power amplifier board uses 7377 amplifier chip, dual circuit design, optional DC12V / AC12V power supply, and uses 2.1 three-channel output. Available for Bluetooth / Wireless Microphone / Fan. Separate design, easy installation, provides volume and subwoofer adjustment. ParametersWorking voltage:DC12V / AC12V Chip:TDA7377 Op amp:LT084 / 324 Working voltage:DC12V / AC12V Output power:38Wx3 Channel …
XH-W1411 220V 10A Smart Electronics LED Digital thermometer Temperature Controller Switch Module
$17.48Test & Measuring ModuleAdd to cartSpecificationsTemperature range:-55- + 120→Temperature measurement accuracy:± 0.3→Resolution:0.1→Temperature range:-19 ~ 99→Control accuracy:1→Temperature probe:NTC10K / B3950 comes standard with 1 meter waterproof probeSupply voltage:220VTemperature:-25 ~ 55→ Humidity 20% -85% (non-condensing)Output Type:10A relay outputsSize:90*60mm/3.54 Inch*2.36 InchHole size:70*50mm/2.76 Inch*1.96 InchFeatures– The board and plastic panels fixed column compartment and lock nut– Connect the power supply according to the drawings …
3Pcs HIFI Amplifier Passive Tone Board Bass Treble Volume Control Preamp Board DIY Kit
$24.99DIY Electronic KitsAdd to cartDescriptionIt is DIY Kit, must be assemble to work. User need technical operation ability.Package included3 x HIFI Amplifier Passive Tone Board Bass Treble Volume Control Preamp Board DIY Kit
100x100cm High Strength Carbon Fiber Cloth for interlayer 3900 mpa
$60.74Carbon FiberAdd to cartSpecificationSize;100 x 100cmWidth; 0.25mmMaterial:Carbon fiberCompressive strength:3900 mpaFeaturesa.Uniform texture, without color. Weaving skills, good gloss.b.Mainly used in aircraft main, tail and body; automotive engine synchronizer, hood, bumpers, decorative pieces; bike frame, wheels, leading; racket, cone; kayaking, snowboarding; various models, helmets , watches, pens, bags.Main purpose1. Aerospace:fuselage, rudder, rocket engine shells, missiles casual flow, such as solar …
100x100cm High Strength Carbon Fiber Cloth for interlayer 3900 mpaRead More
3pcs EQKIT 60 Seconds Electronic Timer Kit DIY Parts Soldering Practice Board
$28.54DIY Electronic KitsAdd to cartInstruction:http://img.staticbg.com/file/products/20180726215941ETI-60-timer-kit.pdfFeatureOperating voltage:DC5VStandby current:≤8mAWorking current:≤10mACountdown:60 secondsCountdown ends prompt:three alarmsSoludering difficulty:GeneralBoard size:84 x 84mmNote:Electronic production kit, require buyer soldering assembly.Package included3 x Electronic Timer K
Reviews
There are no reviews yet.