DIY Airband Radio Receiver Aviation Band Receiver Kit
$43.73
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Description
Like many scanner enthusiasts and ham operators, you are interested in listening in on all the excitement manifest in aeronautic communication, but lack the equipment to pursue your interest, then maybe the Aviation-Band Receiver described in this article is for you.
The Aviation Receiver, designed to tune the 118-135MHz band, features exceptional sensitivity, image rejection, signal-to-noise ratio, and stability.
The receiver is ideally suited to listening in on ground and air communication associated with commercial airlines and general aviation.
Powered from a 9-volt alkaline battery, it can be taken along with your to local airports so that you won’t miss a moment of the action.
And even if you’re nowhere near an airport, this little receiver will pick-up all the ground-to-air and vice-versa communications of any plane or ground facility within about 130 miles (190Km).
Color:Green
Material:CCL
Construction
Once you have obtained all of the components and the board for the Aviation Receiver, construction can begin. A parts-placement diagram is shown in Fig. When assembling the project, take special care that polarity-sensitive components (electrolytic capacitors [keep leads as short as possible], diodes, and transistors) are installed properly. Just one part installed backwards can cause grievous harm!
Inductors (Aircoils) L1,L3,L5 can be made easily on a 5mm drill bit. Before you wind them, scrape the enamel of each end, about 5mm. Then wind the 1.5 turn (2-turns is okay too). I know it can be tricky especially if you have big fingers like me. Begin by installing the passive components (6 jumper wires, sockets, resistors, capacitors, inductors). Followed by installing the active components; diodes, transistors, and IC’s. Once the active components have been installed, check your work for the usual construction errors; cold solder joints, misplaced or reversed-lead components, solder bridges, etc. Once you have determined that he circuit has been correctly assembled, it’s time to consider the enclosure that will house the receiver.
The receiver’s circuit board can be housed in any enclosure that you choose.
Note
Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1-3cm.
Package included
1 x DIY KITs Airband Radio Receiver Aviation Band Receiver
1 x English manual
Weight | 0.081 kg |
---|
Customers Also Viewed
5pcs ESP-32S Matching Adapter Board WIFI bluetooth Module ESP-WROOM-32 Module for DIP
$9.84Smart ModuleAdd to cartFeaturesESP-32S supporting adapter board, 2.54mm pitch, lead RESET and IO 0 port, can be inserted into the breadboard, use DuPont wire leads, etc., to facilitate development and debugging.Package Included5 x ESP-32S Matching Adapter Board
5 Channel Flame Sensor Module Analog Dgital Dual Output Fire Extinguishing Robot Flame Alarm System Module
$13.11Sensor & Detector ModuleAdd to cartFeatures1.Using a five-way flame sensor design, the detection range is wide (the detection range of a common single flame sensor is about 30°, and the range is gradually reduced as the distance increases, the detection range of this product is greater than 120°)2.Can output digital signals (high and low level), easy to use3. can output …
600W Mini 2CH HiFi Digital Audio Stereo Amplifier Bass bluetooth FM Radio Amplifiering Equipment
$109.34Switch AccessoriesAdd to cartSpecificationsColor:BlueType:Support bluetoothInput voltage:220V-240V 50/60Hz 12V(in car)Plug:US plugRated power:80W+80WPeak power:300W+300WChannel:2 CHLoad impedance:4-16ΩSNR:>90 dbFM frequency:88-108MHzDistoration rate:0.05%Frequency:20Hz-20KHz(±3dB)Total harmonic distortion:less than 0.5% (normal operating conditions)Signal input sensitivity:200MV (±30MV)MIC input sensitivity:9mV (±2mV)Record level output:1VAuxiliary output level:1VSensitivity:0.25mV-220mVRC power supply:CR2052 battery(built-in)Features-Mini HIFI digital bluetooth audio power amplifier.-SD Card, U disk, MP3 format play, support bluetooth wireless connection.-Supports FM stereo radio.-Two microphone input …
Reviews
There are no reviews yet.