US-100 Ultrasonic Ranging Module with Temperature Compensated Sensor Dual Mode Serial Port
$10.92
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Characteristic
The US-100 ultrasonic ranging module can provide 2cm-450cm non-contact distance sensing function, wide working voltage, self-contained temperature sensor to correct the ranging result, and also has GPIO, serial port and other communication methods. The dog is stable and reliable.
The module includes a transmitter, receiver and control circuit, which is a piezoelectric sensor that is fabricated using electrostrictive phenomena.
An alternating voltage is applied to the piezoelectric material slice (such as quartz crystal, piezoelectric ceramic, lead bismuth titanate, etc.) to cause it to generate electrostrictive vibration to generate ultrasonic waves. The resonance is generated when the frequency of the applied alternating voltage is equal to the natural frequency of the wafer, and the ultrasonic wave generated at this time is the strongest.
Piezoelectric ultrasonic receivers generally operate using the inverse effect of an ultrasonic generator. The structure is basically the same as that of an ultrasonic generator, and sometimes the same transducer is used as both a generator and a receiver.
When the ultrasonic wave acts on the piezoelectric wafer, the wafer is stretched and contracted, and alternating charges are generated at the two interfaces of the wafer, and then converted into a voltage and amplified to be sent to the measuring circuit, and finally recorded or displayed.
Electrical parameters:US-100 ultrasonic ranging module
Operating Voltage:DC 2.4V~5.5V
Quiescent Current:2mA
Operating temperature:-20~+70 degrees
output method:Level or UART (jumper cap selection)
Induction angle:Less than 15 degrees
Detection distance:2cm-450cm
Detection accuracy:0.3cm+1%
Serial port configuration in UART mode:The baud rate is 9600, the start bit is 1 bit, the stop bit is 1 bit, the data bit is 8 bits, there is no parity, no flow control.
Pin 1:Connect to VCC power supply (DC 2.4V-5.5V).
Pin 2:When it is in UART mode, it is connected to the TX terminal of the external circuit UART; when it is in the level trigger mode, it is connected to the Trig terminal of the external circuit.
Pin 3:When in UART mode, connect to RX terminal of external circuit UART; when it is level trigger mode, connect to Echo terminal of external circuit.
Pin 4/5:Connect the ground of the external circuit, and the two pins are turned on.
Level-triggered ranging works
Before powering up the module, first remove the jumper cap on the mode selection jumper to put the module in level trigger mode.
It can be seen from the figure that only a high level of 10US or more is required to be input to the Trig/TX pin, and the system can send eight 40KHZ ultrasonic pulses and then detect the echo signal. When the echo signal is detected, the module also measures the temperature value, then corrects the ranging result according to the current temperature, and outputs the corrected result through the Echo/RX pin. In this mode, the module converts the distance value to twice the time value at 340m/s, outputs a high level through the Echo terminal, and simultaneously starts the timer, and can read the timer when the port goes low. The value of the high level is the time from the transmission to the return of the ultrasonic wave. The distance value can be calculated based on the duration of this high level. That is, the distance value is:(high time *340m/s)/2.
Note:Since the distance value has been temperature corrected, it is no longer necessary to correct the ultrasonic sound speed according to the ambient temperature, that is, the sound speed is 340m/s regardless of the temperature.
Serial port triggering ranging works
Before the module is powered on, first plug in the jumper cap on the mode selection jumper to make the module in serial port trigger mode.
In this mode, only need to input 0X55 (baud rate 9600) on the Trig/TX pin, the system can send 8 40KHZ ultrasonic pulses and then detect the echo signal. When the echo signal is detected, the module also measures the temperature value, then corrects the ranging result according to the current temperature, and outputs the corrected result through the Echo/RX pin. The output distance value is a total of two bytes, the first byte is the upper 8 bits of the distance (HDate), and the second byte is the lower 8 bits of the distance (LData), in millimeters. That is, the distance value is (HData*256 + LData) mm.
Serial port trigger temperature measurement working principle
Before the module is powered on, first plug in the jumper cap on the mode selection jumper to make the module in serial port trigger mode.
In this mode, only need to input 0X50 (baud rate 9600) on the Trig/TX pin, the system will start the temperature sensor to measure the current temperature, and then output the temperature value through the Echo/RX pin. After measuring the completion temperature, the module will return a byte temperature value (TData), the actual temperature value is TData-45. For example, after sending 0X50 through TX and receiving 0X45 on RX, the temperature value at this time is [69 (0X45 decimal value) -45] = 24 degrees.
Precautions
1. This module should not be connected with power. If you want to have a live connection, first connect the GND terminal of the module first, otherwise it will affect the normal operation of the module.
2. When measuring distance, the area of the measured object is not less than 0.5 square meters and the plane should be flat as much as possible, otherwise the measurement result will be affected.
3. If the test surface is not very regular or when testing a distant object, multiple measurements can be used to correct it.
Package includes
1 x US-100 Ultrasonic Ranging Module
Weight | 0.009 kg |
---|
Customers Also Viewed
3Pcs MB102 Test Developer DIY 830 Hole Solderless PCB Breadboard
$17.32Electronic Accessories & SuppliesAdd to cart3Pcs MB102 Test Developer DIY 830 Hole Solderless PCB BreadboardDescription1 terminal Strip, tie-point 6302 Distribution Strips, tie-point 200Solderless breadboard (MB-102)Wire size:Suitabe for 29-20 AWG wiresSize:About 16.5*5.6*1 cmNote:May has different types random delivery.Package included3 x MB102 Breadboard 830 Hole Solderless PCB
Laser Ceramic Body 28mm Fiber Laser Cutting Machine Head Nozzle Holder Ceramic Ring Parts
$27.89Engraving Parts & AccessoriesAdd to cartSpecificationMaterial:CeramicDiameter:28mmHeight:12mmThe installation type:Internal thread connectionApplication:Fiber laser cutting machinePackage Included1 x Laser Ceramic
MTOLASER PCA-K Pillar Limiter Lens Frame Elevating Set Optical Adjustment Laser Module Holder
$15.27Engraving Parts & AccessoriesAdd to cartDescriptionThe PCA-K pillar limiter elevating set is designed to locate the position of the adjusting rod, which can easily realize the fine-tuning of the optical path calibration without any other optical elements.SpecificationBrand:MTOLASER Model:PCA-KMaterial:Aviation AluminumMain Color:Black + SilverInstallation Diameter:12mm ColumnSize:22mm x 12mmFeatures1. The pillar limited elevating set is designed to locate the position of the adjusting …
Metal Film Resistor Assortment kit LED Diodes Electrolytic Capacitor Ceramic Set Transistor Plastic Bag Package DIY Electronic Components Kits
$32.79Electronic Accessories & SuppliesAdd to cartLED diodes:100pcs LED Assorted KitWhite 5mm 20pcs 3V-3.2V 20mARed 5mm 20pcs 1.8V-2V 20mAGreem 5mm 20pcs 1.8V-2V 20mAYellow 5mm 20pcs 2V-2.3V 20mABlue 5mm 20pcs 3 V-3.2V 20mAWhite 3mm 20pcs 3V-3.2V 20mARed 3mm 20pcs 1.8V-2V 20mAGreem 3mm 20pcs 1.8V-2V 20mAYellow 3mm 20pcs 2V-2.3V 20mABlue 3mm 20pcs 3 V-3.2V 20mAResistance package600pcs 30 values Metal Film Resistor Kit 10R-1M …
1CH Channel Ethernet Relay Network Switch TCPUDP Module Controller with 1 Digital input
$57.38Network ModuleAdd to cartFunction descriptionControl the pull-in and release of 1 relay through the Ethernet network, with a shell. The module supports both TCP and UDP two operation modes, the instructions are simple and easy to understand, and the jog and 1-65535 seconds delay can be specified in the instruction. The module is equipped with VB, host computer …
1CH Channel Ethernet Relay Network Switch TCPUDP Module Controller with 1 Digital inputRead More
STC89C52 DIY Learning Board Kit Suit the Parts 51/AVR Microcontroller Development Board Learning Board
$13.11DIY Electronic KitsAdd to cartThis board to 51 interface designed for platform double reset circuit, the monolithic support are1, On STC series such as STC89, STC11, STC12, STC90 DIP encapsulation (40 feet). Need to download a program via a serial port (COM).2, The AT89S series such as AT89S51 and AT89S52 devices such as DIP encapsulation (40 feet). Need to …
1/2 inch Micro Water Filter Purifier Stainless Steel Front Facing Wire Mesh
$17.00Mesh & Wire ClothAdd to cartDescriptionMicro Water Filter Purifier Stainless Steel Front-facing Wire MeshSpecificationMaterial:PlasticSize:as the picture shows(Pls allow 1-3mm measurement error)FeaturesStrict processConvenient in usePackage include1 x Water Filter Parts
Reviews
There are no reviews yet.