3Pcs DIY Touch Vibration Alarm Kit Electronic Training Teaching
$11.65
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Working principle
The touching vibration alarm consists of touch trigger circuit, vibration trigger circuit and alarm circuit. The 555 time base circuit U1 forms the typical monostable operating mode. The transient time is determined by the values of RP1, R2 and C2.
Usually the circuit is in steady state, 555 time base circuit 3 pin output low, the alarm chip does not alarm because there is no power supply. When the human touch the electrode sheet M, the human body induced by the clutter of the signal injected into the 555 trigger pin 2 through C1, or vibration sensor S1 connect instantly because of the vibration, will both cause the U1’s pin 2 to appear instantly low level , So that the 555 circuit flip into the transient, pin 3 mutate to high level, alarm chip works.
Transient time is over, the time base circuit back to steady state, stop the alarm. The length of the alarm time can be adjusted by changing RP1. LED is a two-color light-emitting diodes, green LED bright after power, use as the power indicator light, the red and green light are bright and shows the overall orange when alarming, the resistance of resistor R5 determines the alarm sound play speed, generally take 180K-240K, pay attention to install the resistor before installing the chip, the entire circuit can work under DC 3-6V.
Note
Battery is not included.
Package included
3 x DIY Touch Vibration Alarm Kit
Weight | 0.039 kg |
---|
Customers Also Viewed
USR-ES1 W5500 Chip SPI to LAN Ethernet Converter TCP/IP Module WIZ820io
$15.30Converter BoardAdd to cart>>>Manual:Click here to openOverviewUSR-ES1 embeds Wiznet’s W5500 chip, which uses hardware logic gates to implement the transport layer and network layer of the TCP/IP protocol stack (such as TCP, UDP, ICMP, IPv4, ARP, IGMP, PPPoE, etc.), and integrates The data link layer, physical layer, and 32K bytes of on-chip RAM serve as data transceiving buffers. …
USR-ES1 W5500 Chip SPI to LAN Ethernet Converter TCP/IP Module WIZ820ioRead More
3pcs TEC1-12715 12V Heat Sink thermoelectric Cooler Peltier Plate Module
$32.04Electronic Accessories & SuppliesAdd to cart40 x 40mm TEC1-12715 12V Heatsink Thermoelectric Cooler Peltier Plate ModuleDescriptionSolid state, vibration free, noise-freeSimple to install and operateThe hot surface need to be good heat sinkSpecificationProduct name:thermoelectric cooler plate moduleModel:TEC1-12715Color:whiteCouples:127Voltage:12VUmax:15.4VImax:15AMax power consumption:231WTmax:70°CQcmax T=0(W):137WSize:40 x 40 x 3.3mmWeight:50gPackage included3 x TEC1-12715 cooler plate module
EQKIT KM-1 DC 6-12V PWM Motor Speed Controller Kit DIY Motor Speed Regulator Set Stepless Speed Control
$8.73Module KitsAdd to cartSpecificationsModel:KM-1Operating voltage:DC 6-12VPCB board size:40 x 40mmCircuit descriptionKM-1 uses PWM (pulse width modulation) to control the speed of the motor, adjust the pulse width duty ratio, so that the speed from zero to the maximum speed stepless speed regulation. The wider the crest width of the control waveform, the faster the motor speed; on the …
20pcs 63V 10000UF 105 High Frequency Temp Electrolytic Capacitor 30mm x 50mm Long Life
$108.62Electronic Accessories & SuppliesAdd to cartSpecificationModel:485622Voltage:63VCapacitance:10000UFTemperature:105→Diameter:30mm / 1.1 inchHeight:50 mm / 2 inchFeaturesLong life, high temperatureHigh-frequency capacitorsPackage included20 x Electrolytic Capacitor
Reviews
There are no reviews yet.