DSTIKE BAD Watch Programmable Watch Atmega32u4 USB Laser VL53L0 Distance Sensor Temperture RTC with 800mAh Battery
$151.66
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
What is it
It is a atmega32u4 development watch with distance sensor, laser, buzzer, RGB LED and RTC inside.
It is pre-flashed with a demo program that can display time, inside temperature (RTC3231’s temperature), and distance.
Push the switch upwards and the watch will detect distance between you and your target. If distance is less than 1m, buzzer will sound ‘B~’ and RGB will turn RED at the same time. The distance sensor can only detect 0-1.2m range.
Push the switch downwards and the laser will be enabled. Push down again and it will turn off the laser.
You can look at the introduction video I made.
Why did you make it
I just wanted to make a cool watch for Arduin beginners. Atmega32u4 could be recognized as a key board for computers. That is why a lot of people use it as a Bad USB. That is also the same reason I use it on this watch. I added a command that can show your computer wifi passwords, so when you connect this watch with a computer a window will jump up and shows all the passwords.
You can change the BadUSB code to do what you want with computer. Just for fun. Do not do bad things.
What makes it special
Bootloader is Arduin Leonardo
Buzzer(Digital Pin 12)
RGB LED(Digital Pin 6)
Laser(Digital Pin 13)
1.3 OLED SH1106(IIC)
SDA(Digital Pin 3)
SCL(Digital Pin 2)
Button Up(Digital Pin 10)
Button Down(Digital Pin 8)
Button Select(Digital Pin 9)
Breakou GPIOs(5V,3V,BAT,GND,GPIO5,SDA,SCL,TXD,RXD,AD0)
VL53L0 Distance Sensor(IIC)
Extremely Accurate DS3231(IIC)
40-70mA power cost(work time depends on your code)
800mAh Li-battery
Indicate charging LED (25%,50%,75%,100%)
Power Switch (Click to turn on, double click to turn off, long click to open highlight LED)
How to program it
Open IDE and select ‘Arduin Leonardo’ in the board option.
Tips
I put all the design files and code on my github. When you try the example code you had better to download libraries into your Arduin IDE first
1.Bad USB
Bad USB code part can only be put at the setup() field. If you put it in the loop() you may have a problem where the computer cannot recognize the watch. You have to re-flash bootloader to fix this problem.
2.PowerKeep
I use IP5306 to power this watch. When IP5306 detect current less than 45mA it will turn off power automatically. So I use a PowerKeep code to simulate every 10 seconds click power button. That will keep ip5306 output power all the time. If you do not add this code, this board may run about 30 seconds and then turn off power automatically.
3.RTC
When you find time does not show correctly, you can flash demo code again. Time will synchronize the same time with your computer.
4.DemoCode
After you figured out how to control each part of this watch you can develop your customized watch! I am sorry I am not very good at software part, if any problem you can inform me at anytime.
Package Inlcuded
1 x DSTIKE BAD Watch Programmable Watch with 800mAh Battery
Weight | 0.24 kg |
---|
Customers Also Viewed
50Pcs 12V Female DC Power Socket Jack Plug Wire Connector Cable CCTV DC 5.5 x 2.1mm
$32.76Module ComponentsAdd to cartFeaturesDC 5.5 x 2.1mm.Wire Specification:0.15mm²Length:Approx. 27cmMax Current Rating:2AMax Power Rating:60WTransmission voltage:1V~38VUsage temperature:-50→~65→Material:Copper WireUse for:Led Driver/ Strip connector/ CCTV Camera.Package Included50 x 12V DC Connector Cables
EMC EMI Low Noise Pre-RF Amplifier 20dB 5MHz-5GHz RFamp002
$87.30RF amplifierAdd to cartParameter1. Power supply voltage:11V-15V DC2. Gain:greater than 20DB in the 30MHz-1GHz frequency band3. Input and output impedance:50┯4. Maximum output power:10dBm5. Input signal:-10DBm6. Bandwidth:30MHz to 3GHz (gain is different under different frequencies)Measured gain (prototype)F=5.0MHZ GAIN=13.15DBF=10.0MHZ GAIN=23.89DBF=30.0MHZ GAIN=27.06DBF=50.0MHZ GAIN=27.92DBF=500.0MHZ GAIN=24.84DBF=1.0GHZ GAIN=22.01DBF=1.5GHZ GAIN=20.72DBF=2.5GHZ GAIN=17.65DBF=3.5GHZ GAIN=10.06DBF=4.0GHZ GAIN=9.09DBF=5.0GHZ GAIN=8.90DB7. Noise figure NF (theoretical value)500MHz@ 0.6dB1GHz@ 0.7dB2GHz@ 0.7dB3GHz@ 1.1dB4GHz@ 1.6dB5GHz@ 2.1dBComparison …
EMC EMI Low Noise Pre-RF Amplifier 20dB 5MHz-5GHz RFamp002Read More
RX24 100W 30R 30RJ Metal Aluminum Case High Power Resistor Golden Metal Shell Case Heatsink Resistance Resistor
$6.55Electronic Accessories & SuppliesAdd to cartFeaturesIt has the characteristics of small size, high power and high precision.It is sealed by professional technology.It has the advantages of stronger heat resistance, higher temperature resistance, moisture resistance, high anti-vibration and explosion protection.Scope of application:Testing power supply, frequency converter, automobile LED lamp, automation equipment, audio, frequency divider, servo industry and other harsh industrial control …
5pcs SRX882 433/315MHz Superheterodyne Receiver Module Board for ASK Transmitter Module
$16.71Smart ModuleAdd to cartItem OverviewThe SRX882 is a super-heterodyne receiver module with a micropower and strong driving force in conjunction with the ASK transmitter module. It has high stability, anti-interference and high cost performance, and also has a strong driving force, which can pass ROHS, FCC, CE and other certifications. The data port can be directly connected to …
5pcs SRX882 433/315MHz Superheterodyne Receiver Module Board for ASK Transmitter ModuleRead More
13.5mm Adjustable Laser Pointer Module Holder Mount Clamp 3 Axis
$42.51Engraving Parts & AccessoriesAdd to cartDescriptionMaterial:stainless steelColor:blackMount Inner Diameter:13.5mmSize:40X60mm/1.57X2.36inch(L*H)Feature1. Stainless steel laser moudle holder2. Professional angle and height adjustable design3. Installed on the laser module,it can become a professional laser pointer or laser locator4. Can also used a as a heatsink for the laser module,extend the laser module life time5. Fit for 12mm diameter laser modulePackage included1X Laser Module Holder
Mask Scary Glow Mask LED Mask for Halloween Mask Party Masks Neon Maske Skeleto Halloween Party Decor
$17.17EL ProductsAdd to cartColor. Red / Color. Orange / Color. Yellow / Color. Blue / Color. Blue / Color. Purple / Color. White / Color. Pink / Color. Fluorescent Green / Color. Green / Color. Transparent Blue /
Reviews
There are no reviews yet.