DSTIKE BAD Watch Programmable Watch Atmega32u4 USB Laser VL53L0 Distance Sensor Temperture RTC with 800mAh Battery
$151.66
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
What is it
It is a atmega32u4 development watch with distance sensor, laser, buzzer, RGB LED and RTC inside.
It is pre-flashed with a demo program that can display time, inside temperature (RTC3231’s temperature), and distance.
Push the switch upwards and the watch will detect distance between you and your target. If distance is less than 1m, buzzer will sound ‘B~’ and RGB will turn RED at the same time. The distance sensor can only detect 0-1.2m range.
Push the switch downwards and the laser will be enabled. Push down again and it will turn off the laser.
You can look at the introduction video I made.
Why did you make it
I just wanted to make a cool watch for Arduin beginners. Atmega32u4 could be recognized as a key board for computers. That is why a lot of people use it as a Bad USB. That is also the same reason I use it on this watch. I added a command that can show your computer wifi passwords, so when you connect this watch with a computer a window will jump up and shows all the passwords.
You can change the BadUSB code to do what you want with computer. Just for fun. Do not do bad things.
What makes it special
Bootloader is Arduin Leonardo
Buzzer(Digital Pin 12)
RGB LED(Digital Pin 6)
Laser(Digital Pin 13)
1.3 OLED SH1106(IIC)
SDA(Digital Pin 3)
SCL(Digital Pin 2)
Button Up(Digital Pin 10)
Button Down(Digital Pin 8)
Button Select(Digital Pin 9)
Breakou GPIOs(5V,3V,BAT,GND,GPIO5,SDA,SCL,TXD,RXD,AD0)
VL53L0 Distance Sensor(IIC)
Extremely Accurate DS3231(IIC)
40-70mA power cost(work time depends on your code)
800mAh Li-battery
Indicate charging LED (25%,50%,75%,100%)
Power Switch (Click to turn on, double click to turn off, long click to open highlight LED)
How to program it
Open IDE and select ‘Arduin Leonardo’ in the board option.
Tips
I put all the design files and code on my github. When you try the example code you had better to download libraries into your Arduin IDE first
1.Bad USB
Bad USB code part can only be put at the setup() field. If you put it in the loop() you may have a problem where the computer cannot recognize the watch. You have to re-flash bootloader to fix this problem.
2.PowerKeep
I use IP5306 to power this watch. When IP5306 detect current less than 45mA it will turn off power automatically. So I use a PowerKeep code to simulate every 10 seconds click power button. That will keep ip5306 output power all the time. If you do not add this code, this board may run about 30 seconds and then turn off power automatically.
3.RTC
When you find time does not show correctly, you can flash demo code again. Time will synchronize the same time with your computer.
4.DemoCode
After you figured out how to control each part of this watch you can develop your customized watch! I am sorry I am not very good at software part, if any problem you can inform me at anytime.
Package Inlcuded
1 x DSTIKE BAD Watch Programmable Watch with 800mAh Battery
Weight | 0.24 kg |
---|
Customers Also Viewed
3pcs 1838T infrared Sensor Receiver Module Board Remote Controller IR Sensor with Cable
$11.26Sensor & Detector ModuleAdd to cartFeatures– Can receive standard 38KHz remote control signals by means of programming can decode the remote control signals– Strong ability to resist electromagnetic interference and light– Widely used in stereo, TV, set-top boxes, digital photo frame, car stereo, remote control toys, satellite receivers, hard disk players, air conditioner, heater, electric fan, lighting and other home …
3pcs 1838T infrared Sensor Receiver Module Board Remote Controller IR Sensor with CableRead More
600V 45A 3 Position Terminal Block Barrier Strip Dual Row Screw Block Covered W/ Removable Clear Plastic insulating Cover
$16.19Terminal BlocksAdd to cartSpecificationModel:TB4503Type:Terminal block Working frequency:High frequencyInterface type:AC/DCRated current:45ARated voltage:600VConductor cross section:0.5-4mm2Number of pin:6Number of bits:3Contact material:IronSize:70mm x 38mm x 24mmFeature:–Moistureproof–High quality guides,durable–High quality thickened conductive parts–High quality iron screw with high strength–Dust proof transparent plastic protective coverPackage Included1 x Terminal block
5Pcs 2 Lamp Backlight Universal LCD CCFL 10V-28V inverter
$26.31Smart ModuleAdd to cart5Pcs 2 Lamp Backlight Universal LCD CCFL 10V-28V Inverter For 10 Inch To 22 Inch ScreenFeatureVoltage:10V ~ 28VCable:300mm(L) / 6 pinSize:122 x 27mm ( L x W )Interface:double light small interfaceInterface definition:1. VCC 2. GND 3. NULL 4. NULL 5. ON/OFFPackage included5 x 2 lamp backlight universal laptop LCD CCFL inverter 10V-28V5 x Cable
18A 3900W EMI High Frequency Power Filter Finished Board for amp Amplifier Board
$20.90Amplifier BoardAdd to cartFeatures1. Power filter function is through the power line access power filter,get a specific frequency of the power signal, or eliminate a specific frequency power signal. By using this feature of the power filter, a square wave complex or complex noise passing through the power filter can be converted into a sine wave of a …
18A 3900W EMI High Frequency Power Filter Finished Board for amp Amplifier BoardRead More
5pcs EQKIT TDL-555 Touch Delay LED Light DIY Kit Touch Delay Lamp Electronic Parts Production Kit DC 5V 3s to 130s Adjustable
$10.12DIY Electronic KitsAdd to cartFunction1. Connect Power,Red LED ON2. Touch and then start to delay and Red LED OFF and 5pcs White LED ON at the same time3. Red LED ON and White LED OFF after delay4. Delay can be adjust by potentiometer for 3-130 secondPackage included5 x EQKIT® TDL-555 Touch Delay LED Light DIY Kit
Waveshare Universal e-Paper Panel Driver HAT SPI Surface for Raspberry Pi 4
$22.95Raspberry Pi & Orange PiAdd to cartOverviewThis is a universal driver board for e-Paper panels, can be used to drive various SPI interface e-Paper from Waveshare.FeaturesStandard Raspberry Pi 40PIN GPIO extension header, supports Raspberry Pi series boards, Jetson NanoSPI interface, for connecting with other controller boards like Raspberry/Arduino/Nucleo, etc.Onboard voltage translator, compatible with 3.3V/5V MCUsComes with development resources and manual (examples …
Waveshare Universal e-Paper Panel Driver HAT SPI Surface for Raspberry Pi 4Read More
Reviews
There are no reviews yet.