3Pcs inverter Boost High Voltage Generator 15KV High Frequency Transformer
$18.14
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Use
School science experiment, electronic equipment, negative ion generator, small scientific production and so on.
Feature
This circuit works to produce a stable high-frequency arc, the temperature is extremely high, can easily ignite the combustible, so it was called a plasma lighter.
Note
This transformer high voltage winding in the inner layer, is the segment skeleton wound, low voltage winding in the outer layer, please do not mistaken for this transformer is high voltage winding and low voltage winding the same way.
The transformer has two primary winding, one of the main group is coarse copper wire, a group of fine copper wire for the feedback winding. The secondary output is high voltage.
Transformers in a coarse and a thin winding together two copper wire is positive, respectively, the main winding tail and feedback winding head, connect the power supply positive.
Before soldering the transformer, the soldering part of the enameled wire head of the paint need to gently scraping with blade and then soldering, please note.
Precautions for product use
1. After the successful production, the transformer must be sealed with epoxy resin or insulating wax to be used for a long time. The air-borne work in the air will cause the coil to break through damage due to the lack of air insulation.
2. The input voltage of the kit is 3.7v. That is, a section 18650 battery voltage, if you need to increase the input voltage (maximum increase to 12V), you need to increase the feedback resistor resistance (we default send 120 ohm), otherwise the transistor is easy to burn. Feedback resistance increased to 150Ω ~ 1.5KΩ or so, the resistance should be adjusted from large to small, do not too small, otherwise will burn transistor or transformer, and should not be too large, too much will impact the output or make the transistor work in the non-switch state to make the fever is serious hot.
transformer design for the 15KV maximum output, which is 1.5 cm arc, the higher the output voltage is likely to damage the transformer. For reliable long-term continuous work, it is recommended to use insulating wax or epoxy resin to completely seal it, prohibit no-load working when no sealed.
Specification
Input voltage:3.7V-4.2V
Current
Output voltage
Output current
High pressure two-stage ignition distance
Size is about:27 x 16 x 21mm (Manual measurement, please understand the error)
Package includes
3 x High Voltage Generator Kit
Schematic diagram
In order to prevent the output 2-line distance too far, resulting in no-load, you can solder a pin in the output, and put the end of the needle into the arc, is conducive to the discharge arc, lik the following show
After the success of the production, if the output terminal connected to a high-voltage capacitor and three high voltage rectifier composed of voltage doubling circuit, can produce DC high voltage, can produce anion generator, the wiring diagram is as follows:
Weight | 0.054 kg |
---|
Customers Also Viewed
30pcs EQKIT Electronic Funny Kits Voice Control LED Melody Light DIY Kits Production Suite Small Electronic Learning Electronic Kits
$56.32DIY Electronic KitsAdd to cartDescriptionVoltage:3-4 .5 VPCB material:FR-4 fiberglass boardDimensions:34 * 34MMPackage included30 x Voice Control LED Melody Light DIY Kits
10pcs Transparent Protective ABS Case Support Cooling Fan for Raspberry Pi 4 Model B
$58.27Raspberry Pi & Orange PiAdd to cartOverviewThis is a new design ABS case to protect your Raspberry Pi 4 Model B computer, and it is only comepatible with your Raspberry Pi 4 Model B, not support other versions. Also support install a dc 5v cooling fan. The GPIO pin interface is available to us if you do not install the cooling …
10pcs Transparent Protective ABS Case Support Cooling Fan for Raspberry Pi 4 Model BRead More
10pcs Roller Lever Arm Micro Switch AC 250V HV-156-1C25
$13.11Electronic Accessories & SuppliesAdd to cart10pcs Roller Lever Arm Micro Switch AC 250V HV-156-1C25DescriptionSize:27.8 x 10.3 x 15.9mmRoller Diameter:4.75mmLever Length:28mmRating:15A AC250VWithstand Voltage:AC1, 0000V 1 MinuteInsulation Resistance:100mΩ DC500VContact ResistanceSoldering Temperature:250°C Max 3 sec.Ambient Temperature used:-25°C to +80°CAmbient Humidity UsedOperating Force:160Part number is HV-156-1C25Package included10 x Micro Switch
Solar TPMS LED Wireless Tire Pressure Monitoring System with 4 internal Sensor
$168.06SwitchesAdd to cartFeatures-This wireless tire pressure monitoring system comes with four built-in sensors and a digital monitor to monitor the tire pressure/temperature-By employing the advanced wireless sensors which highly integrated pressure and temperature sensor, we provide the amazing and reliable TPMS for you-Oil will be decreased when tires work under lower pressure, this item can reduce fuel …
Solar TPMS LED Wireless Tire Pressure Monitoring System with 4 internal SensorRead More
Deek-Robot W-1213 intelligent Digital Display Fish Tank Climbing Pet Greenhouse Planting Hatching and Breeding Temperature Controller
$26.23Test & Measuring ModuleAdd to cartProduct parameterProduct name:Intelligent temperature controllerProduct model:W-1213Power supply voltage:AC110-220VWorking frequency:50HZTemperature range:-40C~+120CTemperature measurement accuracy:÷0.5CSensor cable length:100CMSize:79.5*43*35mmShell material:surface shell ABS, bottom shell flame retardant ABSBattery:CR1220 3V button battery(not included)Display panel descriptionHeat (corresponding icon display):heating mode, in heating mode, heating the relay works.Cool (corresponding icon display):Cooling mode, in cooling mode, cooling the relay works.Timer:Timer switch, in timer mode, the …
Waveshare IMX219-160 Camera 160 Degree Field of View 8 Million Pixels for Jetson Nano
$54.66Smart ModuleAdd to cartFeaturesSupports NVIDIA Jetson Nano Developer Kit, Compute Module 3/3+8 MegapixelsSensor:IMX219Resolution:3280 ≠ 2464Lens specificationsCMOS size:1/4inchAperture (F):2.35Focal Length:3.15mmAngle of View (diagonal):160 degreeDistortion4 screw holesUsed for attachmentProvides 3.3V power outputDimension:25mm ≠ 24mmApplicationsCombined with the Jetson Nano AI computer, this camera suits for AI projects such asFace recognitionRoad mark detectionLicense plate recognitionPackage includes:(the Jetson Nano does not includes)1 x …
Waveshare IMX219-160 Camera 160 Degree Field of View 8 Million Pixels for Jetson NanoRead More
10Pairs MC4 Connector Male And Female MC4 Solar Panel Connector 30A 1000V for PV Cable 2.5/4/6mm Solar Panel Connect
$26.23Electronic Accessories & SuppliesAdd to cartSpecificationArticle number:MC4Rated voltage 1000 VRated impulse voltage:1000 VTest voltage:6 kV (50Hz)Suitable for cables:10, 12, 14 AWG (2.5mm2 / 4mm2 / 6mm 2;)Rated current:24 A-14 AWG (2.5mm 2;), 30A-12 and 10 AWG (4mm 2; and 6mm 2;)Protection class:IP67Contact material:copper, silver platedInsulation material:PC / PAOperating temperature:-40 ° C + 90 ° CThe security class:IIFlame Class:UL94-V0Contact resistance:≤5mΩInsertion / …
Reviews
There are no reviews yet.