10Pcs inverter Boost High Voltage Generator 15KV High Frequency Transformer
$55.49
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Use
School science experiment, electronic equipment, negative ion generator, small scientific production and so on.
Feature
This circuit works to produce a stable high-frequency arc, the temperature is extremely high, can easily ignite the combustible, so it was called a plasma lighter.
Note
This transformer high voltage winding in the inner layer, is the segment skeleton wound, low voltage winding in the outer layer, please do not mistaken for this transformer is high voltage winding and low voltage winding the same way.
The transformer has two primary winding, one of the main group is coarse copper wire, a group of fine copper wire for the feedback winding. The secondary output is high voltage.
Transformers in a coarse and a thin winding together two copper wire is positive, respectively, the main winding tail and feedback winding head, connect the power supply positive.
Before soldering the transformer, the soldering part of the enameled wire head of the paint need to gently scraping with blade and then soldering, please note.
Precautions for product use
1. After the successful production, the transformer must be sealed with epoxy resin or insulating wax to be used for a long time. The air-borne work in the air will cause the coil to break through damage due to the lack of air insulation.
2. The input voltage of the kit is 3.7v. That is, a section 18650 battery voltage, if you need to increase the input voltage (maximum increase to 12V), you need to increase the feedback resistor resistance (we default send 120 ohm), otherwise the transistor is easy to burn. Feedback resistance increased to 150Ω ~ 1.5KΩ or so, the resistance should be adjusted from large to small, do not too small, otherwise will burn transistor or transformer, and should not be too large, too much will impact the output or make the transistor work in the non-switch state to make the fever is serious hot.
transformer design for the 15KV maximum output, which is 1.5 cm arc, the higher the output voltage is likely to damage the transformer. For reliable long-term continuous work, it is recommended to use insulating wax or epoxy resin to completely seal it, prohibit no-load working when no sealed.
Specification
Input voltage:3.7V-4.2V
Current
Output voltage
Output current
High pressure two-stage ignition distance
Size is about:27 x 16 x 21mm (Manual measurement, please understand the error)
Package includes
10 x High Voltage Generator Kit
Schematic diagram
In order to prevent the output 2-line distance too far, resulting in no-load, you can solder a pin in the output, and put the end of the needle into the arc, is conducive to the discharge arc, lik the following show
After the success of the production, if the output terminal connected to a high-voltage capacitor and three high voltage rectifier composed of voltage doubling circuit, can produce DC high voltage, can produce anion generator, the wiring diagram is as follows:
Weight | 0.18 kg |
---|
Customers Also Viewed
ULN2003 Stepper Motor Driver Board Test Module for AVR SMD
$4.36Driver ModuleAdd to cartDescriptionULN2003 is a high voltage and high current Darlington transistor array products with high current gain, high operating voltage, wide temperature range, with strong load capacity and other characteristics, adapted to the requirements of various types of the high-speed high-power drive system.Features1. Using ULN2003 high-power Darlington chip-driven stepper motor2. Increased output expansion interface.3. A, B, …
ULN2003 Stepper Motor Driver Board Test Module for AVR SMDRead More
3pcs DD40CRTA 2 in 1 Charger Module DC DC Step Down Module Converter DC 6.5-40V to 4.2V 5V Charging Board 9V 12V 24V to 4.2V Regulator
$18.54Power Supply ModuleAdd to cartSize ConversionInchesCentimetersPlease according to your own measurements to choose your suitable size. The tags inside the items will show in our Asian (Type) size.SpecificationsInput voltage 6.5-40VOutput 1:DC 4.2V/0-1A, as battery ChargerOutput 2:DC 5V/0-1A, as 40-6.5V to 5V Step down module Maximum charging current:1000mA Full charge voltage:4.2V÷2%.Led indicator‘OK’ LED is fully charged OR battery failure indicator; …
3 Pcs Sliver Aluminum Alloy Case with Cooling Fan Protective Shell Metal Enclosure fit for Raspberry Pi 4 Model B
$58.52Raspberry Pi & Orange PiAdd to cartThe Raspberry Pi is not included, you could get it here:Raspberry Pi 4 Model BDescriptionThis is a Protective case designed specifically for Raspberry Pi 4 Model BThe product is made of aluminum and it is very strong,high hardness, pressure resistance, strong metallic luster, not easy to rust,it can perfectly protect your motherboard Aluminum alloy material …
Heavy Duty Iron Boxing Punch Bag Wall Bracket Mount Hanging Stand Holder Hanger
$121.49Lab Clamp & StandAdd to cartFeature1. Heavy duty gym-quality Punch Bag wall bracket made from iron added strength and treated with nti-static spray is perfect for in and outdoor training activity!2. Reinforced iron arm protrudes 60CM from wall and can withstand heavy bags up to 800KG with ease.3. Three bolt points, attaches perfectly into brick or block walls.4. Mount this …
Heavy Duty Iron Boxing Punch Bag Wall Bracket Mount Hanging Stand Holder HangerRead More
20pcs DC 5V Step Up Boost Converter Voltage Regulate Power Supply Module Board with Enable ON/OFF
$72.05Boost & Buck ModuleAdd to cartSize ConversionInchesCentimetersPlease according to your own measurements to choose your suitable size. The tags inside the items will show in our Asian (Type) size.SpecificationsWorking frequency:1MHzUp to 94% Efficiency (usually is 75%-91%) Quiescent current:Turn on output 210uA,Turn off output 5uA. Operating temperature:-40~+85 →Storage temperature:-65~+150 →Size:20 x 15 x 6mmWeight:1.5g ProtectionOver current protection(OCP)Over voltage protection(OVP)Short circuit protection(SCP)Over …
Reviews
There are no reviews yet.