10Pcs inverter Boost High Voltage Generator 15KV High Frequency Transformer
$55.49
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Use
School science experiment, electronic equipment, negative ion generator, small scientific production and so on.
Feature
This circuit works to produce a stable high-frequency arc, the temperature is extremely high, can easily ignite the combustible, so it was called a plasma lighter.
Note
This transformer high voltage winding in the inner layer, is the segment skeleton wound, low voltage winding in the outer layer, please do not mistaken for this transformer is high voltage winding and low voltage winding the same way.
The transformer has two primary winding, one of the main group is coarse copper wire, a group of fine copper wire for the feedback winding. The secondary output is high voltage.
Transformers in a coarse and a thin winding together two copper wire is positive, respectively, the main winding tail and feedback winding head, connect the power supply positive.
Before soldering the transformer, the soldering part of the enameled wire head of the paint need to gently scraping with blade and then soldering, please note.
Precautions for product use
1. After the successful production, the transformer must be sealed with epoxy resin or insulating wax to be used for a long time. The air-borne work in the air will cause the coil to break through damage due to the lack of air insulation.
2. The input voltage of the kit is 3.7v. That is, a section 18650 battery voltage, if you need to increase the input voltage (maximum increase to 12V), you need to increase the feedback resistor resistance (we default send 120 ohm), otherwise the transistor is easy to burn. Feedback resistance increased to 150Ω ~ 1.5KΩ or so, the resistance should be adjusted from large to small, do not too small, otherwise will burn transistor or transformer, and should not be too large, too much will impact the output or make the transistor work in the non-switch state to make the fever is serious hot.
transformer design for the 15KV maximum output, which is 1.5 cm arc, the higher the output voltage is likely to damage the transformer. For reliable long-term continuous work, it is recommended to use insulating wax or epoxy resin to completely seal it, prohibit no-load working when no sealed.
Specification
Input voltage:3.7V-4.2V
Current
Output voltage
Output current
High pressure two-stage ignition distance
Size is about:27 x 16 x 21mm (Manual measurement, please understand the error)
Package includes
10 x High Voltage Generator Kit
Schematic diagram
In order to prevent the output 2-line distance too far, resulting in no-load, you can solder a pin in the output, and put the end of the needle into the arc, is conducive to the discharge arc, lik the following show
After the success of the production, if the output terminal connected to a high-voltage capacitor and three high voltage rectifier composed of voltage doubling circuit, can produce DC high voltage, can produce anion generator, the wiring diagram is as follows:
Weight | 0.18 kg |
---|
Customers Also Viewed
24S 72V Lithium Battery 3.2V Power Protection Board 30A-180A with Temperature Protection Equalization Function Overcurrent Protection BMS PCB
$60.74Battery Protection ModuleAdd to cartCurrent 30A / Current 40A / Current 50A / Current 60A / Current 70A / Current 100A / Current 130A / Current 150A / Current 180A /
ONLY LED Light Lighting Kit for Lego 42096 Technic Porsche 911 RSR Bricks Toys
$18.50DIY Electronic KitsAdd to cartDescriptionInterface:USBColor:As the picture shownFitmentONLY For Lego Technic Porsche 911 RSR (42096) Bricks ToysFeaturesEasy to install.LED powered by USB.Make your model more cool.ONLY For Lego 42096 Technic Porsche 911 RSR Bricks.Package Included1 x LED Light Kit(Model Not Included)1 x Battery Case
500mL Clear Borosilicate Glass Filtering Flask Vacuum Filtration Flask Bottle Lab Glassware
$40.49Glassware KitAdd to cartDescription– Flasks are glass or plastic containers for storing or collecting chemical samples or solutions in scientific laboratories.– It shaped like a cone with a wide, flat base that narrows to a neck opening, which can be closed with a stopper or cap.SpecificationMaterial:Borosilicate GlassCapacity:500mLFlask Style:Filtering (vacuum)Package Included1 x Glass Filtering Flask
2400mAh Portable Solar Panel Charger Reusable Solar Generator System USB Port with Lamp Lighting
$64.79Solar GeneratorAdd to cartFeature1.Reusable solar generator, solar charging, environmental protection and energy saving, you can use it in anywhere when there is adequate sunshine.2.Equipped with USB charging cable, you can charge your electronic products easily with the built-in large capacity battery, you can charge for mobile phones, MP3, MP4, digital cameras and other electronic products.3.White LED light and …
20pcs Sensor Shield V5.0 Sensor Expansion Board for DIY Electronic Building Blocks of Robot Parts
$62.36Sensor & Detector ModuleAdd to cartFeaturesLatest Sensor Shield V5.0 sensor expansion board is still before laminated design PCB Immersion Gold processing technology, the motherboard is not only Duemilanove 2009 controller of digital and analog interface extended to the steering gear line order form, also ad hoc IIC interface, 32 Servo controller interface , bluetooth module communication interface, SD card module …
Reviews
There are no reviews yet.