inverter Boost High Voltage Generator 15KV High Frequency Transformer Arc Ignition Igniter Coil
$8.73
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Use
School science experiment, electronic equipment, negative ion generator, small scientific production and so on.
Feature
This circuit works to produce a stable high-frequency arc, the temperature is extremely high, can easily ignite the combustible, so it was called a plasma lighter.
Note
This transformer high voltage winding in the inner layer, is the segment skeleton wound, low voltage winding in the outer layer, please do not mistaken for this transformer is high voltage winding and low voltage winding the same way.
The transformer has two primary winding, one of the main group is coarse copper wire, a group of fine copper wire for the feedback winding. The secondary output is high voltage.
Transformer in a coarse and a thin winding together two copper wire is positive, respectively, the main winding tail and feedback winding head, connect the power supply positive.
Before soldering the transformer, the soldering part of the enameled wire head of the paint need to gently scraping with blade and then soldering, please note.
Precautions for product use
1. After the successful production, the transformer must be sealed with epoxy resin or insulating wax to be used for a long time. The air-borne work in the air will cause the coil to break through damage due to the lack of air insulation.
2. The input voltage of the kit is 3.7v. That is, a section 18650 battery voltage, if you need to increase the input voltage (maximum increase to 12V), you need to increase the feedback resistor resistance (we default send 120 ohm), otherwise the transistor is easy to burn. Feedback resistance increased to 150┯ ~ 1.5K┯ or so, the resistance should be adjusted from large to small, do not too small, otherwise will burn transistor or transformer, and should not be too large, too much will impact the output or make the transistor work in the non-switch state to make the fever is serious hot.
transformer design for the 15KV maximum output, which is 1.5 cm arc, the higher the output voltage is likely to damage the transformer. For reliable long-term continuous work, it is recommended to use insulating wax or epoxy resin to completely seal it, prohibit no-load working when no sealed.
Specification
Input voltage:3.7V-4.2V
Current
Output voltage
Output current
High pressure two-stage ignition distance
Size is about:27 x 16 x 21mm (Manual measurement, please understand the error)
Package includes
1 x High Voltage Generator
Schematic diagram
In order to prevent the output 2-line distance too far, resulting in no-load, you can solder a pin in the output, and put the end of the needle into the arc, is conducive to the discharge arc, lik the following show
After the success of the production, if the output terminal connected to a high-voltage capacitor and three high voltage rectifier composed of voltage doubling circuit, can produce DC high voltage, can produce anion generator, the wiring diagram is as follows:
Weight | 0.018 kg |
---|
Customers Also Viewed
100 Pcs Copper Cable Lugs Kit SC6-6 ~SC35-10 Electrical Terminal Block Wire Connectors
$70.86ConnectorsAdd to cartSpecificationModel:SC6-6~SC35-10Material:Tin Plated CopperColor:SilverSize:6mm²/10mm²/16mm²/25mm²/35mm²Mount Hole:6 mm/8 mm/10 mmBox Size(L*W*H):280 x 126 x 14 mmQuantity:100 PcsFeaturesElectro-plated tin exterior.Premium quality copper material, environmentally friendly, safe for using.These tube lugs have a bell shaped end allowing for easy insertion of the cable.Acceptable working temperature is -55℃ to 100℃ and are suitable for applications in the Australian Climate.Copper lugs are …
100 Pcs Copper Cable Lugs Kit SC6-6 ~SC35-10 Electrical Terminal Block Wire ConnectorsRead More
TDA7377 Subwoofer Amplifier Audio Board 38Wx3 Mini Home Amp 2.1 Channel HiFi Stereo Power Amplifier DIY
$21.86Amplifier BoardAdd to cartDescriptionThe power amplifier board uses 7377 amplifier chip, dual circuit design, optional DC12V / AC12V power supply, and uses 2.1 three-channel output. Available for Bluetooth / Wireless Microphone / Fan. Separate design, easy installation, provides volume and subwoofer adjustment. ParametersWorking voltage:DC12V / AC12V Chip:TDA7377 Op amp:LT084 / 324 Working voltage:DC12V / AC12V Output power:38Wx3 Channel …
XH-W1411 220V 10A Smart Electronics LED Digital thermometer Temperature Controller Switch Module
$17.48Test & Measuring ModuleAdd to cartSpecificationsTemperature range:-55- + 120→Temperature measurement accuracy:± 0.3→Resolution:0.1→Temperature range:-19 ~ 99→Control accuracy:1→Temperature probe:NTC10K / B3950 comes standard with 1 meter waterproof probeSupply voltage:220VTemperature:-25 ~ 55→ Humidity 20% -85% (non-condensing)Output Type:10A relay outputsSize:90*60mm/3.54 Inch*2.36 InchHole size:70*50mm/2.76 Inch*1.96 InchFeatures– The board and plastic panels fixed column compartment and lock nut– Connect the power supply according to the drawings …
3Pcs HIFI Amplifier Passive Tone Board Bass Treble Volume Control Preamp Board DIY Kit
$24.99DIY Electronic KitsAdd to cartDescriptionIt is DIY Kit, must be assemble to work. User need technical operation ability.Package included3 x HIFI Amplifier Passive Tone Board Bass Treble Volume Control Preamp Board DIY Kit
100x100cm High Strength Carbon Fiber Cloth for interlayer 3900 mpa
$60.74Carbon FiberAdd to cartSpecificationSize;100 x 100cmWidth; 0.25mmMaterial:Carbon fiberCompressive strength:3900 mpaFeaturesa.Uniform texture, without color. Weaving skills, good gloss.b.Mainly used in aircraft main, tail and body; automotive engine synchronizer, hood, bumpers, decorative pieces; bike frame, wheels, leading; racket, cone; kayaking, snowboarding; various models, helmets , watches, pens, bags.Main purpose1. Aerospace:fuselage, rudder, rocket engine shells, missiles casual flow, such as solar …
100x100cm High Strength Carbon Fiber Cloth for interlayer 3900 mpaRead More
3pcs EQKIT 60 Seconds Electronic Timer Kit DIY Parts Soldering Practice Board
$28.54DIY Electronic KitsAdd to cartInstruction:http://img.staticbg.com/file/products/20180726215941ETI-60-timer-kit.pdfFeatureOperating voltage:DC5VStandby current:≤8mAWorking current:≤10mACountdown:60 secondsCountdown ends prompt:three alarmsSoludering difficulty:GeneralBoard size:84 x 84mmNote:Electronic production kit, require buyer soldering assembly.Package included3 x Electronic Timer K
Reviews
There are no reviews yet.