inverter Boost High Voltage Generator 15KV High Frequency Transformer Arc Ignition Igniter Coil
$8.73
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Use
School science experiment, electronic equipment, negative ion generator, small scientific production and so on.
Feature
This circuit works to produce a stable high-frequency arc, the temperature is extremely high, can easily ignite the combustible, so it was called a plasma lighter.
Note
This transformer high voltage winding in the inner layer, is the segment skeleton wound, low voltage winding in the outer layer, please do not mistaken for this transformer is high voltage winding and low voltage winding the same way.
The transformer has two primary winding, one of the main group is coarse copper wire, a group of fine copper wire for the feedback winding. The secondary output is high voltage.
Transformer in a coarse and a thin winding together two copper wire is positive, respectively, the main winding tail and feedback winding head, connect the power supply positive.
Before soldering the transformer, the soldering part of the enameled wire head of the paint need to gently scraping with blade and then soldering, please note.
Precautions for product use
1. After the successful production, the transformer must be sealed with epoxy resin or insulating wax to be used for a long time. The air-borne work in the air will cause the coil to break through damage due to the lack of air insulation.
2. The input voltage of the kit is 3.7v. That is, a section 18650 battery voltage, if you need to increase the input voltage (maximum increase to 12V), you need to increase the feedback resistor resistance (we default send 120 ohm), otherwise the transistor is easy to burn. Feedback resistance increased to 150┯ ~ 1.5K┯ or so, the resistance should be adjusted from large to small, do not too small, otherwise will burn transistor or transformer, and should not be too large, too much will impact the output or make the transistor work in the non-switch state to make the fever is serious hot.
transformer design for the 15KV maximum output, which is 1.5 cm arc, the higher the output voltage is likely to damage the transformer. For reliable long-term continuous work, it is recommended to use insulating wax or epoxy resin to completely seal it, prohibit no-load working when no sealed.
Specification
Input voltage:3.7V-4.2V
Current
Output voltage
Output current
High pressure two-stage ignition distance
Size is about:27 x 16 x 21mm (Manual measurement, please understand the error)
Package includes
1 x High Voltage Generator
Schematic diagram
In order to prevent the output 2-line distance too far, resulting in no-load, you can solder a pin in the output, and put the end of the needle into the arc, is conducive to the discharge arc, lik the following show
After the success of the production, if the output terminal connected to a high-voltage capacitor and three high voltage rectifier composed of voltage doubling circuit, can produce DC high voltage, can produce anion generator, the wiring diagram is as follows:
Weight | 0.018 kg |
---|
Customers Also Viewed
10pcs 433MHZ ASK Wireless Transmission Module TX11 High Power Module infinite Emission Circuit Board
$19.40Smart ModuleAdd to cartFeatures(1) The transmission power is large, and the transmission power is greater than 30 mW;(2) Wide operating voltage, 2.5V-9V;(3) Operating frequency:433.92 MHz(4) Using SAW frequency stabilization (+-75KHZ), the working frequency is stable;(5) With the RXB8 receiving module, the distance can reach 800 meters;(6) Static power consumption Low emission is current consumption:10mA, there is basically no …
SZWENGAO WG8-40S1210 8-40V to 12V 10A Automatic Buck Boost Power Converter Car Voltage Regulator Step Down Step Up Module
$39.35Boost & Buck ModuleAdd to cartFeatures*Designed according to CE/RoHS*100% full power, high stability output*100% full load aging test*Imported components*Imported high-quality thermal silica gel potting, waterproof, dustproof and shockproof* Die-cast aluminum alloy shell, small size, simple installation*Internal protection functions such as over current, low voltage, over temperature, short circuit, reverse connection, etc.*Wide voltage input, high conversion efficiency of 88-90%*Long service life …
10Pcs Wemos DS18B20 Module for D1 Mini DS18B20 Temperature Measurement Sensor Module
$36.17Sensor & Detector ModuleAdd to cartFeatures1. Supporting the D1 MINI2. The Ar-duino compatible, using A-rduino IDE for programming3. 11 the XI/O pins4. 1 XADC pin (0-3.3V)5. Support the OTA onlinePackage included10 x DS18B20 Module20 x Long female pin20 x Short female pin20 x Normal pin
ASK Wireless Receiving Module with Decoding EV1527 Encoding Transmitter
$10.92Smart ModuleAdd to cartFeaturesThe latest anti-lost code self-recovery function solves the trouble of losing code.The latest anti-interference software is involved to prevent accidental startWidely compatible, PT2262, PT2260, EV1527, PT2240, etc.Ultra-wide pulse width range:105 to 515 oscillating resistorsIn jog mode:support combination codeSelf-locking mode:support combination codeIn the interlock mode:4 independent open and close, the combination code is closedYou can learn …
ASK Wireless Receiving Module with Decoding EV1527 Encoding TransmitterRead More
50W 18V Monocrystaline Al-Alloy at back Solar Panel Dual 12V/5V DC USB Charger for Car RV Boat
$88.07Smart Robot & Solar PanelAdd to cartFeatures– EVA+PET at front panel and Al-Alloy at back, light-weight but durable.– USB and DC output interface for more purpose.– Equipped with 12V DC5.5×2.1 & 5V USB output interface.– Dedicated for 12V battery and 5V device charging. – High output 3000mAh USB, can full-charge an iX in 1.5h in max power.– Mono-crystalline solar Cell with …
Reviews
There are no reviews yet.