Flame Flare Detection Module Flame Sensor 12V Relay Board infrared Receiver Module
$7.11
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Usage
Various flames, fire source detection, relay output, can be connected to 220V high current equipment
Features
1. It can detect flame or light source with wavelength in the range of 760 nm to 1100 nm. The flame distance of the lighter is 80 cm. The larger the flame, the farther the test distance is.
2. The detection angle is about 60 degrees, especially sensitive to the flame spectrum
3. The sensitivity is adjustable (blue digital potentiometer adjustment in the figure)
4. The comparator output directly triggers the relay
5. The external dimensions:50x26x19mm, with fixed bolt holes for easy installation
6. The output has a blue terminal block, convenient wiring
Electrical parameters
Supply voltage:12VDC
Current:greater than 150mA
Load:250V 10A AC or 30V 10A DC
Instructions for use
1. The flame sensor is most sensitive to the flame and also responds to the sunlight. It is generally used for flame alarms and other purposes.
2. By adjusting the potentiometer, the intensity of the sensor’s induced flame can be set. When the flame exceeds the set threshold, the relay is closed, the common end is connected to the normally open end, and when the flame is lower than the set threshold, the relay is disconnected. The common end is connected to the normally closed end;
3. The common end, normally open, normally closed three ports are equivalent to a dual control switch, when the relay coil is powered, the common end is open to the normally open end, when there is no electricity, the common end and the normally closed end are turned on;
4. The sensor and the flame should be kept at a certain distance to avoid damage to the sensor at high temperature. The flame distance of the lighter is 80cm. The larger the flame, the farther the test distance is.
Package includes
1 x Flame sensor module
Weight | 0.017 kg |
---|
Customers Also Viewed
5pcs RS232 to TTL Serial Converter Module DB9 Connector MAX3232 Serial Module with Cable
$21.38Converter BoardAdd to cartFeatureIt is widely used in radio modification, phone flash, GPS, vehicle detection, DVD flash, hard disk repair set-top box upgradeIt can be used to program STC MCU, NXP MCU, Renesas MCU, STM32 MCU, N+-2EC MCU CommunicationPort:TX RX VCC GNDChip:domestic MAX3232Package includes5 x Serial Module5 x Cable
Original JYETech 13805K DSO138mini DIY Digital Oscilloscope Kit SMD Pre-soldered with Case
$37.91DIY Electronic KitsAdd to cartDSO138mini brings in the following improvementsBetter structure and smaller size. The bulky pin-headers connecting the LCD and main board in old DSO138 has been eliminated. The soldering of these pin-headers has being found problematic for beginners.USB or battery powered. This makes the scope much more convenient to be used as a portable device. New version …
Original JYETech 13805K DSO138mini DIY Digital Oscilloscope Kit SMD Pre-soldered with CaseRead More
CJMCU-2112 CP2112 Evaluation Sensor for CCS811 Debugging Board USB to I2C Communication Converter Module
$16.67Sensor & Detector ModuleAdd to cartFeatureDirect connection to PC via USBDirect connection to host system via I2CSimple software GUI for easy setup and data loggingDetermine the effects of Temperature & HumidityIntelligent algorithms to output TVOC / eCO2 levelsPackage includes1 x Sensor Module
3 Pcs Red Acrylic Wall Mounted Protective Case Support Cooling Fan for Raspberry Pi 4 Model B
$35.10Raspberry Pi & Orange PiAdd to cartDescription– Wall Mounting Available– Red Blue Black Optional– Support Adding Cooling Fan– Compatible With Raspberry Pi 4B– Make of Transparent Acrylic, could check the board status easilyThere is a Protective Film on the board surface, please take it off before using.Package Included3* RED Acrylic Case Kit
5pcs CTS DTR USB Adapter Pro Mini Download cable USB to RS232 TTL Serial Ports CH340 Replace FT232 CP2102 PL2303 UART TB196
$23.80Converter BoardAdd to cartFeatures– This product use CH340 chips, stable performance, fully compatible with USB1.1,USB2.0,USB3.0 , baud rate up to 256 kbps; – Uses:Replace FT232 for Arduiuo Pro Mini Download – With receiver indicator,transmitter indicator, and power indicator.– Chip:CH340C– Compatible with PRO MINI download port– Board size:18mm x 30mm(Does not include USB ports and pins)– Supports the following …
10Pcs XH Pitch 2.54mm Single Head 4Pin 4Way Wire To Board Connector 15cm 24AWG with Socket
$6.55Electronic Accessories & SuppliesAdd to cartFeatureType:XH2.54 Single Head WirePin Number:4 PinWire Gauge:24AWG Pitch:2.54mmLength:15cmQuantity:10 Sets(10Pcs Single Head Wire + 10Pcs Socket )Note:the cable color may have different.Package included10 x XH2.54 Single-Head 4Pin 4Way Wire To Board Connector10 x Socket
2.4G Wireless Remote Control Module Transmitter and Receiver Module Kit Transmission Reception Communication 6 Channel Output
$8.26Smart ModuleAdd to cartTY24D-TX is the transmitting module, TY24D-RX is the receiving module. The transmitting module only needs to provide 3.3V power supply and transmitting button and one LED as the transmitting status indication. The output port corresponding to the receiving module can output the level signal, and the module has the output status. Select to select the …
2M*45cm Window Film Privacy Static Cling Stained Glass Sticker Home office Decor
$30.50PlasticsAdd to cartSpecificationsMaterial:PVCSize:45cm X 200cmFeatures– Energy-saving and environmental protection. No gum paste, paste can be repeated.– Deadening UV intrusion, protecting indoor objects fading and aging.– Filter light and reduce glare, protect the skin and vision.– Easy to mount and clean.How to use1. First clean the surface of the pasting position, pasting surfaces should be smooth, not be …
2M*45cm Window Film Privacy Static Cling Stained Glass Sticker Home office DecorRead More
Reviews
There are no reviews yet.