JK12-A 12V Time Adjustable Relay Module with LED Digital Tube Dynamic Display Countdown Single Chip Relay
$10.92
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Usage
This module starts work after triggering. If you need to set the power to start timing, then you can connect the two trigger lines directly.
inchTriggerinch is simply a touch of two lines. It can be a short touch or a long time. Timing starts when you touch each other.
K:Switching signal trigger, valid at the leading edge
RY:Relay
After power-on, RY has no action. After K is triggered, RY is immediately turned on. After the delay, the RY is disconnected after the countdown ends. When K is triggered again during the delay, it will immediately jump to the end of the delay (ie, RY is disconnected).
Features
– The button trigger type triggers the action to start immediately and delays. (If the button end is shorted before power-on, each power-on will be turned on and delayed by the setting)
– Display:The set time is displayed during adjustment; during the delay, the countdown is displayed dynamically.
– Switch on the load immediately after the trigger and disconnect the load after the specified time.
– During the delay, the button operation immediately stops the delay and returns to the initial state.
– During the delay, the digital tube reduces the brightness and counts down the delay to display the remaining time in real time.
– Set the time by adjustable resistor. The adjustable range is from 1 to 99. The unit can be selected by jumper. When the jumper is connected to the second, the adjustable range is 1-99 seconds. The jumper is connected to the time division. The adjustable range is 1-99 points.
– Board size:70mm x 40mm, height less than 18mm
Package Included
1 x JK12-A 12V Time Adjustable Relay Module with LED Digital Tube Dynamic Display
Weight | 0.029 kg |
---|
Customers Also Viewed
5pcs ESP-32S Matching Adapter Board WIFI bluetooth Module ESP-WROOM-32 Module for DIP
$9.84Smart ModuleAdd to cartFeaturesESP-32S supporting adapter board, 2.54mm pitch, lead RESET and IO 0 port, can be inserted into the breadboard, use DuPont wire leads, etc., to facilitate development and debugging.Package Included5 x ESP-32S Matching Adapter Board
5 Channel Flame Sensor Module Analog Dgital Dual Output Fire Extinguishing Robot Flame Alarm System Module
$13.11Sensor & Detector ModuleAdd to cartFeatures1.Using a five-way flame sensor design, the detection range is wide (the detection range of a common single flame sensor is about 30°, and the range is gradually reduced as the distance increases, the detection range of this product is greater than 120°)2.Can output digital signals (high and low level), easy to use3. can output …
600W Mini 2CH HiFi Digital Audio Stereo Amplifier Bass bluetooth FM Radio Amplifiering Equipment
$109.34Switch AccessoriesAdd to cartSpecificationsColor:BlueType:Support bluetoothInput voltage:220V-240V 50/60Hz 12V(in car)Plug:US plugRated power:80W+80WPeak power:300W+300WChannel:2 CHLoad impedance:4-16ΩSNR:>90 dbFM frequency:88-108MHzDistoration rate:0.05%Frequency:20Hz-20KHz(±3dB)Total harmonic distortion:less than 0.5% (normal operating conditions)Signal input sensitivity:200MV (±30MV)MIC input sensitivity:9mV (±2mV)Record level output:1VAuxiliary output level:1VSensitivity:0.25mV-220mVRC power supply:CR2052 battery(built-in)Features-Mini HIFI digital bluetooth audio power amplifier.-SD Card, U disk, MP3 format play, support bluetooth wireless connection.-Supports FM stereo radio.-Two microphone input …
Reviews
There are no reviews yet.