RIDEN LD25 Electronic Load Resistor USB interface Discharge Battery Test LED Display Fan
$24.04
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Technical Parameters
Rated operational voltage:DC4-25.0V:Max discharging power:25W
Rated operational current:0.25-4.00A (when fan don’t work, the min. constant current is 0.05A ):Fan Speed:Large size intelligent temperature control fan, speed 5800±10%RPM
Constant current resolution:±(1%+3 digits):Heat dispatch method:intelligent temperature
control fan + All aluminum fan
Working temperature:-10→-40→:Adjustable potentiometer:Preci sion multiloop adjustable potentiometer
Display mode:4 bit LED tube:Expansion port:Micro USB port, Type-C port
Product weight:56.51g:Product size:83.8×41.1×27.9mm
Product Structure
A. Micro USB port:MAX current 2A
B.USB male port (widened power wire, MAX current 4A)
C. Type-C port:MAX current 4A
D. All aluminum fan
E. Intelligent temperature control fan
F. 4 Bit LED tube
G. Preci sion multiloop adjustable potentiometer
H. “SET Inch button:press “SET Inch to switch display status, Press and hold the button to set the load output recovery mode after protection removed.
I. “ON/OFF Inch button:press the button to open or close output. Press and hold the button to set the boot default status of open or close
Function Introduction
a. Protection function
OVP (over-voltage protection):there is OVP at 25-30V; it will be damaged permanently over 30V.at OVP, LED show OVP, as picture 1 show)
OTP(over-temperature protection):load temperature is over 80→, the LED show OTP, as picture 2 show.
OPP(over-power protection):the power is over 80→, the LED show OPP, as picture 3 show.
b. Set output recovery mode after load entering protection status, manual or automatic
c. View the voltage value, current value and power value of the load.
d. Intelligent temperature control fan. When the current is over 2A or the temperature is over 40→, the fan will start.
e. Preci sion multiloop adjustable potentiometer:you can adjust the current precisely, upto 0.01A. so you don’t need to adjust a big current mistakenly to damage the power supply. So the power supply will not be damaged due to mistakenly adjustment
f. you can set default boot status freely, open or close.
Operation Instruction
The load is powered at the range of 4-25.0V (the input polarity cannot be reversed, otherwise the product is permanently damaged and cannot be repaired), the LED will be flashing to remind current setting value, waiting for output. Press ON/OFF button, open output to start work.
1. Adjust output current value.
Turning the rotary control clockwise increases the value and anticlockwise decreases the value. According to the needs of the situation, the potentiometer can realize coarse adjustment or fine adjustment. The fine adjustment can be accurate to 0.01A.
2, Adjust LED display status
Press “SET Inch to adjust the LED display status, default display output current value. Press “SET Inch button to display *.**A, **.*P, **.*V followed by recycling.
3. Open or close load output
Press “ON/OFF Inch button, you can open or close load output
4, Set load default boot status (open or close status, Factory default close status)
Press and hold “ON/OFF Inch button to set load default boot status freely. Press and hold “ON/OFF Inch button, if the LED will display “–ON Inch, as picture 4, the load will open output when power on next time; If the LED display Inch-OFF Inch, as picture 5 show, the LED will display current value flashing at last shutdown when power on next time, then press “ON/OFF Inch button to open output.
5, Set the load output recovery mode after protection removed.
Press and hold “SET Inch button, to set output recovery mode after protection removed. Press and hold “SET Inch button, if the LED will display “–ON Inch, as picture 4, and the protection was removed, the load will recover to work; If the LED display Inch-OFF Inch, as picture 5 show, and the protection was removed, the LED still show protection status, then press “ON/OFF ‘button, the display will display present setting current flashing, then press “ON/OFF‘ button again, the load recover to work.
NOTE:Please check the output current of power bank carefully. The current of the power bank is small, so adjust smaller current when the load was used.
Application
Assist to measure Micro USB cable good or not
Assist to measure Type-C cable good or not
Assist to measure output current capacity of charger good or not
The usage of large batch ageing test at the charger factory
Information
LD25 user manual download page:http://www.mediafire.com/folder/q2o63jc8df6qc/LD25
NOTE
This product has no reverse connection protection, the input polarity cannot be reversed, otherwise the product is permanently damaged and cannot be repaired.
Package included
1 x LD25 Electronic Load
Weight | 0.056 kg |
---|
Customers Also Viewed
5pcs RS232 to TTL Serial Converter Module DB9 Connector MAX3232 Serial Module with Cable
$21.38Converter BoardAdd to cartFeatureIt is widely used in radio modification, phone flash, GPS, vehicle detection, DVD flash, hard disk repair set-top box upgradeIt can be used to program STC MCU, NXP MCU, Renesas MCU, STM32 MCU, N+-2EC MCU CommunicationPort:TX RX VCC GNDChip:domestic MAX3232Package includes5 x Serial Module5 x Cable
Original JYETech 13805K DSO138mini DIY Digital Oscilloscope Kit SMD Pre-soldered with Case
$37.91DIY Electronic KitsAdd to cartDSO138mini brings in the following improvementsBetter structure and smaller size. The bulky pin-headers connecting the LCD and main board in old DSO138 has been eliminated. The soldering of these pin-headers has being found problematic for beginners.USB or battery powered. This makes the scope much more convenient to be used as a portable device. New version …
Original JYETech 13805K DSO138mini DIY Digital Oscilloscope Kit SMD Pre-soldered with CaseRead More
CJMCU-2112 CP2112 Evaluation Sensor for CCS811 Debugging Board USB to I2C Communication Converter Module
$16.67Sensor & Detector ModuleAdd to cartFeatureDirect connection to PC via USBDirect connection to host system via I2CSimple software GUI for easy setup and data loggingDetermine the effects of Temperature & HumidityIntelligent algorithms to output TVOC / eCO2 levelsPackage includes1 x Sensor Module
3 Pcs Red Acrylic Wall Mounted Protective Case Support Cooling Fan for Raspberry Pi 4 Model B
$35.10Raspberry Pi & Orange PiAdd to cartDescription– Wall Mounting Available– Red Blue Black Optional– Support Adding Cooling Fan– Compatible With Raspberry Pi 4B– Make of Transparent Acrylic, could check the board status easilyThere is a Protective Film on the board surface, please take it off before using.Package Included3* RED Acrylic Case Kit
5pcs CTS DTR USB Adapter Pro Mini Download cable USB to RS232 TTL Serial Ports CH340 Replace FT232 CP2102 PL2303 UART TB196
$23.80Converter BoardAdd to cartFeatures– This product use CH340 chips, stable performance, fully compatible with USB1.1,USB2.0,USB3.0 , baud rate up to 256 kbps; – Uses:Replace FT232 for Arduiuo Pro Mini Download – With receiver indicator,transmitter indicator, and power indicator.– Chip:CH340C– Compatible with PRO MINI download port– Board size:18mm x 30mm(Does not include USB ports and pins)– Supports the following …
10Pcs XH Pitch 2.54mm Single Head 4Pin 4Way Wire To Board Connector 15cm 24AWG with Socket
$6.55Electronic Accessories & SuppliesAdd to cartFeatureType:XH2.54 Single Head WirePin Number:4 PinWire Gauge:24AWG Pitch:2.54mmLength:15cmQuantity:10 Sets(10Pcs Single Head Wire + 10Pcs Socket )Note:the cable color may have different.Package included10 x XH2.54 Single-Head 4Pin 4Way Wire To Board Connector10 x Socket
2.4G Wireless Remote Control Module Transmitter and Receiver Module Kit Transmission Reception Communication 6 Channel Output
$8.26Smart ModuleAdd to cartTY24D-TX is the transmitting module, TY24D-RX is the receiving module. The transmitting module only needs to provide 3.3V power supply and transmitting button and one LED as the transmitting status indication. The output port corresponding to the receiving module can output the level signal, and the module has the output status. Select to select the …
2M*45cm Window Film Privacy Static Cling Stained Glass Sticker Home office Decor
$30.50PlasticsAdd to cartSpecificationsMaterial:PVCSize:45cm X 200cmFeatures– Energy-saving and environmental protection. No gum paste, paste can be repeated.– Deadening UV intrusion, protecting indoor objects fading and aging.– Filter light and reduce glare, protect the skin and vision.– Easy to mount and clean.How to use1. First clean the surface of the pasting position, pasting surfaces should be smooth, not be …
2M*45cm Window Film Privacy Static Cling Stained Glass Sticker Home office DecorRead More
Reviews
There are no reviews yet.