JK11S-100S-5V 10A 0-100S Adjustable ON-OFFf Delay Module Timer Cycle Switch infinite Loop Relay Module
$8.73
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Specifications
Voltage:5V DC
Quiescent current:8mA
Operating current:95mA
Trigger:passive switch trigger, response time is 0.03 seconds (the trigger terminal can not access the active signal)
Minimum on-off time:0.2 seconds
Load capacity:10A
Output form:normally open + normally closed
Size:70*20*19mm
Features
– Using industrial-grade single-chip microcomputer to control time, high precision and stable performance;
– Two adjustable resistors are used to adjust the time, and the connection duration and the disconnection time can be independently adjusted;
– The external contact is activated, and the timing is started by shorting the self-reset button. It is also possible to start the countdown by shorting the triggers together to achieve power-on;
– The time range is divided into 0-100 seconds.
Basic working principle
Taking the factory standard setting as an example, the red LED will light when the power is turned on, and the relay is in the off state. When shorted at the trigger end, the module green light is on and immediately enters the working state. Triggering again in the working state will stop working.
In the working state, the relay will pass T1 seconds, break T2 seconds, pass T1 seconds, break T2 seconds… infinite loop. T1 T2 is the length of time the user adjusts with an adjustable resistor.
Instructions
– Power access
The module is connected to the power supply according to the correct power supply voltage and polarity. The red line of the power supply terminal is positive and the black line is negative.
– Trigger line access
The two white lines of the trigger end are connected to a switch, and the module can be started by tapping the switch, and then the switch is stopped by tapping the switch. The trigger switch can be a tact switch, a micro switch, an optocoupler C-E terminal, a relay contact, and the like.
– Normal speed and quick mode settings
The OP1 jumper is used to select normal speed and fast mode, and the shipment defaults to normal speed.
– Loop mode and single mode settings
The OP2 jumper is used to select the loop mode and the single mode, and the shipment defaults to the loop mode.
Cycle mode:After starting, the relay is on-off-on-off-disconnect…, and it is cycled according to the set duration;
Single trigger:After starting, the relay is turned on, and the relay is turned off after T1 duration. (After disconnection, the action ends and waits for trigger again)
Precautions
1. The module power supply is not protected against reverse protection, because it is important to remember that the power supply cannot be connected.
2. The trigger terminal can only be connected to the passive switch, not to the voltage signal. Doing so can damage the module.
3. When the resistance load is connected, no special treatment is needed; when the capacitive load is connected, the relay module is easily damaged by electricity. It is recommended to use the AC contactor derated or the contact current of the motor should be considered within 10A.
Package Included
1 x JK11S-5V 100S Delay Adjustable Multi-function Relay Module
Weight | 0.019 kg |
---|
Customers Also Viewed
5pcs RS232 to TTL Serial Converter Module DB9 Connector MAX3232 Serial Module with Cable
$21.38Converter BoardAdd to cartFeatureIt is widely used in radio modification, phone flash, GPS, vehicle detection, DVD flash, hard disk repair set-top box upgradeIt can be used to program STC MCU, NXP MCU, Renesas MCU, STM32 MCU, N+-2EC MCU CommunicationPort:TX RX VCC GNDChip:domestic MAX3232Package includes5 x Serial Module5 x Cable
Original JYETech 13805K DSO138mini DIY Digital Oscilloscope Kit SMD Pre-soldered with Case
$37.91DIY Electronic KitsAdd to cartDSO138mini brings in the following improvementsBetter structure and smaller size. The bulky pin-headers connecting the LCD and main board in old DSO138 has been eliminated. The soldering of these pin-headers has being found problematic for beginners.USB or battery powered. This makes the scope much more convenient to be used as a portable device. New version …
Original JYETech 13805K DSO138mini DIY Digital Oscilloscope Kit SMD Pre-soldered with CaseRead More
CJMCU-2112 CP2112 Evaluation Sensor for CCS811 Debugging Board USB to I2C Communication Converter Module
$16.67Sensor & Detector ModuleAdd to cartFeatureDirect connection to PC via USBDirect connection to host system via I2CSimple software GUI for easy setup and data loggingDetermine the effects of Temperature & HumidityIntelligent algorithms to output TVOC / eCO2 levelsPackage includes1 x Sensor Module
3 Pcs Red Acrylic Wall Mounted Protective Case Support Cooling Fan for Raspberry Pi 4 Model B
$35.10Raspberry Pi & Orange PiAdd to cartDescription– Wall Mounting Available– Red Blue Black Optional– Support Adding Cooling Fan– Compatible With Raspberry Pi 4B– Make of Transparent Acrylic, could check the board status easilyThere is a Protective Film on the board surface, please take it off before using.Package Included3* RED Acrylic Case Kit
5pcs CTS DTR USB Adapter Pro Mini Download cable USB to RS232 TTL Serial Ports CH340 Replace FT232 CP2102 PL2303 UART TB196
$23.80Converter BoardAdd to cartFeatures– This product use CH340 chips, stable performance, fully compatible with USB1.1,USB2.0,USB3.0 , baud rate up to 256 kbps; – Uses:Replace FT232 for Arduiuo Pro Mini Download – With receiver indicator,transmitter indicator, and power indicator.– Chip:CH340C– Compatible with PRO MINI download port– Board size:18mm x 30mm(Does not include USB ports and pins)– Supports the following …
10Pcs XH Pitch 2.54mm Single Head 4Pin 4Way Wire To Board Connector 15cm 24AWG with Socket
$6.55Electronic Accessories & SuppliesAdd to cartFeatureType:XH2.54 Single Head WirePin Number:4 PinWire Gauge:24AWG Pitch:2.54mmLength:15cmQuantity:10 Sets(10Pcs Single Head Wire + 10Pcs Socket )Note:the cable color may have different.Package included10 x XH2.54 Single-Head 4Pin 4Way Wire To Board Connector10 x Socket
2.4G Wireless Remote Control Module Transmitter and Receiver Module Kit Transmission Reception Communication 6 Channel Output
$8.26Smart ModuleAdd to cartTY24D-TX is the transmitting module, TY24D-RX is the receiving module. The transmitting module only needs to provide 3.3V power supply and transmitting button and one LED as the transmitting status indication. The output port corresponding to the receiving module can output the level signal, and the module has the output status. Select to select the …
2M*45cm Window Film Privacy Static Cling Stained Glass Sticker Home office Decor
$30.50PlasticsAdd to cartSpecificationsMaterial:PVCSize:45cm X 200cmFeatures– Energy-saving and environmental protection. No gum paste, paste can be repeated.– Deadening UV intrusion, protecting indoor objects fading and aging.– Filter light and reduce glare, protect the skin and vision.– Easy to mount and clean.How to use1. First clean the surface of the pasting position, pasting surfaces should be smooth, not be …
2M*45cm Window Film Privacy Static Cling Stained Glass Sticker Home office DecorRead More
Reviews
There are no reviews yet.