ZB2L3 18650 Battery Capacity Tester External Load Discharge Type 1.2-12V Tester with 2 7.5 Resistors
$15.30
Type With 2*5W+1*50W Resistor / Type With 1*50W Resistor / Type With 2*5W Resistor /
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Specification
Power supply voltage:DC4.5-6V (micro USB interface)
Working current:no more than 70mA
Discharge voltage:1.00V-15.00V resolution 0.01V
Termination voltage range:0.5-11.0V
Support current through:maximum 3.000A resolution 0.001A
Maximum voltage measurement error:1% + 0.02V
Maximum current measurement error:1.2%+-0.002A
The highest battery capacity range:9999Ah (1Ah=1000mAh). The larger value is switched by the decimal point shift. When it is lower than 10Ah, it is displayed as X.XXX, and when it is above 10Ah, it is displayed as XX.XX, and so on.
Board size:50mmX37mm
Finished product size:50mmX37mmX17mm (length X width X height maximum position size, including copper foot height)
Board and accessories weight:single board 28g (including copper column), two 5W ceramic resistor 9g, 50W resistance about 27g (including line)
Note
In order to improve the voltage measurement accuracy, this circuit specially designed the DC offset. When the terminal is not connected, it will display a small voltage, which does not affect the actual measurement. If you short-circuit the input terminal (absolute 0V), it will display 0. . If you want to understand the principle, you can check the superposition theorem in electrical engineering.
During the use of resistance discharge, the resistance load will be severely heated, please pay attention to safety! 50W aluminum shell resistor (has been welded a high temperature wire), please install it on the metal plate!
Instructions
1. The battery under test should be fully charged first.
2. Connect the positive pole of the battery under test to the positive input, the negative pole to the input negative pole, and the reverse polarity (the reverse connection with the load may damage the circuit)! Connect the load to the output positive and output negative, and give the tester micro USB working power (not available for desktop or notebook USB), and the battery voltage is displayed.
3. To start the test directly, just press the “OK Inch button, the tester can automatically set the appropriate termination voltage according to the battery full charge voltage, and will flash the display 3 times to start the test. Need to manually set the termination voltage only need to press the inch+inch or inch-inch button to modify the battery voltage display state, the termination voltage display is P beginning, the latter represents the voltage value, the resolution is 0.1V, after setting, press inchOKinch inchstart testing.
4. After the test starts, the tester will turn on the electronic switch that controls the load. The test process data display will be displayed between the discharge capacity (Ah), the current discharge current (A) and the battery voltage (V). When the battery voltage reaches the set termination voltage, the tester cuts off the load control switch, and the display data stays on the capacity (Ah) and flashes rapidly with the corresponding indicator light. The capacity displayed at this time is the actual discharge capacity of the battery. “OK Inch can terminate the flashing to make the data display stably. Press the “OK Inch button again to return to the power-on state and replace the battery test.
Error code and meaning
Err1:Battery voltage is higher than 15V
Err2:Battery voltage is lower than the set termination voltage
Err3:The battery cannot withstand the load discharge current or the line internal resistance is too large
Err4:The current is too large (current exceeds 3.1A)
Err5:Improper use or wiring error has caused the device to burn out and cannot be used (current sampling or control switch MOS burned)
Secondary calibration operation (after self-running calibration, it means to give up the warranty)
Press and hold the three buttons at the same time to power on the tester, enter the calibration mode, first display the number of calibration records and then enter the official calibration sampling program display 0u0A, then short-circuit the input positive and negative, then press the inchOKinch button to complete the display J10u, Apply 10.00V standard DC voltage between the input positive and negative poles, then press the “OK Inch button, then display J2.0A, apply 2.0A constant DC current to the output negative pole (inflow direction) and input negative pole (outflow direction) and press Move the “OK Inch button to complete the calibration. The tester pre-audits the calibration data. If the calibration data is reliable, it will display 4 calibration numbers and then exit. If the pre-audit considers the data to be unreliable, the data will be discarded.
Package includes
1 x Tester
1/2/3 x Resistor (optional)
Weight | 0.08 kg |
---|
Customers Also Viewed
150W 18V Mono Solar Panel Dual USB 12V/5V DC Monocrystalline Solar Charger for Car RV Boat Battery Charger Waterproof
$164.01Solar PanelAdd to cart150W 18V Mono Solar Panel Dual USB 12V/5V DC Monocrystalline Flexible Solar Charger For Car RV Boat Battery ChargerFeatures1.Equipped with 12V DC5.5×2.1 & 5V USB output interface.2.Dedicated for 12V battery and 5V device charging.3.EVA+PET at front panel, flexible, light-weight but durable.4.Mono-crystalline solar Cell with efficient up to 21%.5.4x eyelet and free 2x carabiners for mounting …
DIY 5×7 Prototype Paper PCB Universal Experiment Matrix Circuit Board
$4.36Module ComponentsAdd to cartDescriptionMaterial:Single Side Copper PCB.Hole Dia:about 1mm.Hole pitch:standard 2.54mm.For point to point DIY soldering.Size:5cm x 7cm – 1.97inch x 2.76inch.Quantity:1PCPackage Included1 x PCB Board
FR4 300x200mm Double Side Copper Clad Laminate PCB Board Fiberboard CCL
$17.48Other Module BoardAdd to cartFR4 300x200mm Double Side Copper Clad Laminate PCB Board Fiberboard CCLSpecificationPanel Size:Approx. 300mm x 200mm or 11.8inch x 7.88inch (inch)Thickness:0.06inch ±0.005 (1.5mm ± 0.15)Weight:Approx. 194g eachLayers:Double SidePanel:FR4Operating temperature:Up to 140 °C or 285°FDescriptionThis Double PCB Copper Clad Laminate Board is made of copper foil by the hot-pressing technology.Super-fine steel-wool, Restore4, Tarn-X, roscherite, Zap or similar …
FR4 300x200mm Double Side Copper Clad Laminate PCB Board Fiberboard CCLRead More
10pcs DC Jack Power 7~12V to DC5V/3.3V Step Down Converter Voltage Regulator Power Supply Module for Breadboad OPEN-SMART for Arduino – products that work with official for Arduino boards
$34.43Power Supply ModuleAdd to cartSize ConversionInchesCentimetersPlease according to your own measurements to choose your suitable size. The tags inside the items will show in our Asian (Type) size.DescriptionThis is a mini LDO step-down power module based on AMS1117-5.0 and AMS1117-3.3, and it output fixed 5V / 3.3V.It is a small size, lightweight, especially for model airplanes, smart cars, DIY …
60A DC Brush Motor Speed Controller forward Reverse PWM Control Pulse Width Speed Digital Display 10-55V/3KW
$69.50Motor PWM Speed ControllerAdd to cartThe main purpose1. All kinds of general-purpose DC brush motor speed control2. Various types of automotive motor speed control (automobile cooling fan speed control, car fan speed control, car wiper motor speed control, car air conditioning fan speed control)3. Production line conveyor speed control, pipeline exhaust fan speed regulation, treadmill speed regulation, multiple computer fan …
24Value 500Pcs 0.1uF-1000uF Electrolytic Capacitors + 10Value 600 Pcs 0.1uF-10uF Ceramic Capacitor Assortment Box Kit
$32.79Module ComponentsAdd to cartProduct FeaturesThe nice sturdy box helps you keep all caps in order.Assortment Box for easy access.All of the capacitor is marked the value,easy to find what you need.High quality and long life. Package Included1 x 10Value 600pcs Ceramic Capacitor1 x 24Value 500pcs Electrolytic Capacitor
5Pcs KY-015 DHT11 Temperature Humidity Sensor Module
$17.16Sensor & Detector ModuleAdd to cart5Pcs KY-015 DHT11 Temperature Humidity Sensor Module ForDescriptionThe sensor module is including resistive humidity sensing component and NTC temperature testingThe compatible digital temperature humidity sensor module is component and connected with 8-byte MCUGreat anti-interference ability and durableWith fixed bolt hole for easy installation3 DO small plate switch digital output interface connected microcontroller IO portTwo module …
5Pcs KY-015 DHT11 Temperature Humidity Sensor ModuleRead More
100pcs 270uF 16V 8x8mm Low ESR 16V270uF for Motherboard VGA Solid Capacitor
$29.08Electronic Accessories & SuppliesAdd to cartDescriptionLow ESR, high ripple current capabilityESR 5mΩ max (2 to 4VDC)Longer life(20000 hours at 106 Celsius)Rated voltage:2 to 16VDCCategory temperature:-55 to +105 CelsiusTolerance:+/-20%(M)Package included100 x Solid Capacitors
Reviews
There are no reviews yet.