HW-M543 DC12V~24V/AC220V intelligent Digital Display Temperature and Humidity Controller
$46.56
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Specification
Name:Digital Display Temperature and Humidity Controller
Brand:HW
Model:HW-M543
Control type:temperature and humidity
Working Voltage:DC 12V~24V/AC 220V
Output capacity:maximum 10A
Measurement object:air, water
Temperature range:-20~60 →
Temperature measurement error:÷0.1 →
Humidity range:0-100 %RH
Humidity measurement error:0.2 %
Installation type:Embedded
Dimensions:105*70*38 mm
Hole size:81*57 mm
Weight:About 154g
Package included
1 x Temperature and Humidity Controller
Setting instructions
1. Correctly connect the power supply and the temperature and humidity control equipment according to the wiring diagram, pay attention not to connect the temperature and humidity control equipment wrongly. When connecting the DC12~24V power supply, you must distinguish the positive and negative poles. AC220V does not divide the zero live wire.
2. Stop temperature setting
Press the set button (SET), when the red screen number starts to flash, press the up and down buttons to adjust and set the stop temperature you want; after setting, wait for 10 seconds without operation, the system automatically saves the data.
3. Heating or cooling mode setting
Long press the up button, when the red screen displays C-0, press the set button to enter the C-0 mode setting, press the up and down buttons to switch between the blue screen L and H, L stands for heating, H stands for cooling. (Note:The temperature control load you connect to at L must be a heating device, and at H, the load you connect must be a refrigerating device.) After setting, wait 10 seconds, the system automatically saves the data.
4. Temperature difference setting
Long press the up key, when the red screen shows C-0, press the up and down keys to switch to the C-1 temperature difference setting, press the setting key again to enter the temperature difference setting, and then press the up and down keys to adjust the setting you want Temperature difference value; wait 10 seconds after setting, the system automatically saves the data. (If the stop temperature is set to 35C, the mode is set to L heating mode, and the temperature difference is set to 5, then the start temperature is 35-5=30C and the temperature control range is between 30~35C. On the contrary, if the mode is set to H cooling mode , Then the starting temperature is 35 + 5=40C, and the temperature control range is between 35~40→)
5. Temperature calibration
Long press the up button, when the red screen displays C-0, press the up and down buttons to switch to the C-2 temperature correction mode, press the setting button once to enter the correction mode, and then press the up and down buttons to adjust and set the difference you want If the actual temperature is 28C and the probe detection temperature is 28.2C, then the correction difference can be set to -0.2; if the detection temperature is low, the correction difference can be adjusted higher. After setting, wait 10 seconds, the system will automatically save the data.
6. Stop humidity setting
Press the set button (SET), the red screen numbers start to flash, press the set button again to switch to the blue screen numbers flashing, and then press the up and down keys to adjust and set the stop humidity value you want; after setting, wait for 10 without operation Seconds, the system automatically saves the data.
7. Humidification or dehumidification mode setting
Long press the adjustment key, when the red screen displays H-0, press the set key to enter the H-0 mode setting, press the up and down keys to switch between the blue screen L and H, L stands for humidification, H stands for dehumidification. (Note:The humidity control load you connect to at L must be a humidifying device, and at H, the load you connect to must be a dehumidifying device.) After setting, wait 10 seconds, and the system automatically saves the data.
8. Humidity difference setting
Long press the adjustment key, when the red screen displays H-0, press the up and down keys to switch to the H-1 humidity difference setting, press the setting key to enter the humidity difference setting, press the up and down keys to adjust the setting you want After setting the difference, wait 10 seconds, the system automatically saves the data. (If the stop humidity is set to 50%RH, the mode is set to L humidification mode, the humidity difference is set to 5%RH, then the start humidity is 50-5=45%RH, and the humidity control range is between 45-50%RH, on the contrary If the mode is set to H dehumidification mode, then the starting humidity is 50 + 5 = 55%RH, and the humidity control range is between 50~55%RH)
9. Humidity calibration
Long press the adjustment key, when the red screen displays H-0, press the up and down keys to switch to the H-2 humidity correction mode, press the set key once to enter the correction mode, press the up and down keys to adjust the set difference; such as actual humidity It is 56%RH, the humidity detected by the probe is 56.2%RH, then the correction difference can be set to -0.2; if the detection temperature is low, the correction difference can be adjusted higher. After setting, wait 10 seconds, the system automatically saves the data.
CodeNamePredetermined areaDefault parameters
H-0Mode settingL:Humidify H:DehumidificationL:Heating mode
H-1 Humidity difference0.1-50%RH10%RH
H-2Humidity calibration-10 and 10%RH0.0%RH
10. Restore factory settings
Press the up and down keys at the same time for 5 seconds, when the screen displays 888, the factory restoration is complete.
Weight | 0.132 kg |
---|
Customers Also Viewed
5pcs ST-LINK V2 Programmer Emulator Mini STLINK Downloader for STM8 / STM32 MCU Development Board
$45.35Test & Measuring ModuleAdd to cartSize ConversionInchesCentimetersPlease according to your own measurements to choose your suitable size. The tags inside the items will show in our Asian (Type) size.Description– Only U disk size and compatible with official ST-LINK V2.– Support official firmware upgrade, support all series of STM8 (SWIM interface), STM32(SWD interface).– Two-channel power output 5V / 3.3V and easier …
5pcs Breadboard Power Supply Module Circuit Test 3.3V 5V Switchable
$24.83Power Supply ModuleAdd to cartDescriptionThe size is exactly the same as most bread plates.Small size, suitable for all kinds of experimental equipment.It has the function of current limiting protection.The interface is popular, and the switching voltage can be switched.Input voltage:5VOutput voltage:5V/3.3V switchableOutput current:less than 500mASize:53 x 11mmPackage Included5 x Power Supply Module
3pcs Audio Speaker Protection Board Amplifier Components DC Protect Kit DIY
$24.37DIY Electronic KitsAdd to cartSpecificationInput voltage:AC12-15 VSize(L*W*H):6x 4 x 2.5 cm (Finished)FeatureWith power on delay (about 3 seconds) and DC protection (control voltage around 1 V)With LED status display, when the protection light, the normal work time offUsing 15 A large current relayWorking voltage aAC 12 to 15 V, need independent power supply.Package includes3 x Double-sided circuit boards 3 …
3pcs Audio Speaker Protection Board Amplifier Components DC Protect Kit DIYRead More
5Pcs AMS1117 3.3V Power Supply Module with DC Socket And Switch
$9.02Power Supply ModuleAdd to cartDescription1. onboard AMS1117-3.3 chip2. onboard DC input voltage range of 4.75 V to 12 V3. the onboard 7 * 7 self-locking switch, convenient to control power supply turned on and off during the test4. the onboard power light, indicating whether the power supply5. 4-way output voltage interface, convenient connection during the test6. The board size:48.5 …
5Pcs AMS1117 3.3V Power Supply Module with DC Socket And SwitchRead More
32Pcs Science Chemical Experiment Demonstration Tools Reagent Alcohol Lamp Full Set Storage Box
$89.79Lab Clamp & StandAdd to cartSpecificationType:Chemical Experiment BoxMaterial:Plastic, GlassFeatures1. High quality materials. Environmentally friendly and durable.2. Deepen understanding:thinking at your own hands can give your child a deeper understanding of knowledge.3. The variety of experimental tools is rich, which can meet different experimental needsPackage IncludedItem:QuantityBlue and Red Cup:2 SetFour Treasure Box:1 PcsAlcohol Lamp:2 PcsDropping Bottle:2 PcsSpray Bottle:1 PcsBule Dropping Bottle:3 …
3Pcs T2310 AC110V 220V Programmable Digital Time Delay Switch Relay T2310 Normally Open Timer Control Module 0-999S/Min/Hour
$32.79Test & Measuring ModuleAdd to cartFeatureIndependent crystal oscillator, more accurate timing1. Convenient direct output wiring2. Add buzzer and audible alarm3. Add pause button to stop urgently5. Start and stop setting mode, provincial conversion, which is more convenient6. Automatically save when power off, run automatically when power on7. Timing units can be set separately, with 36 working combinations8. Timing range:0-999 seconds, …
5pcs 30CM 1M Portable Photosensitive Dry Film for Circuit Photoresist Sheet for Plating Hole Covering Etching for Producing PCB Board
$21.78Electronic Accessories & SuppliesAdd to cartFeaturesUniversal used in producing PCB board, attach on the PCB surface to make it photosensitive.Suitable for electroplating, hole covering and etching.Great hole covering ability.High resolution.Great adaptive capacity to different material.Durable in pH 8.0-8.5 situation.1.5mil dry film fully covers a 0.25inch height hole.Suitable for usual plating bath, no wrinkle or color error.SpecificationWidth:approx. 30 cm/11.81inchLength:approx. 100 cm/39.37inchOperating …
Reviews
There are no reviews yet.