5pcs MQ-4 Methane Natural Gas Sensor Module Shield Liquefied Electronic Detector Module
$20.68
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Specification
– The gas sensing material used in the MQ-4 gas sensor is tin dioxide (SnO2) with low conductivity in clean air.
– When there is a flammable gas in the environment where the sensor is located, the conductivity of the sensor increases as the concentration of flammable gas in the air increases.
– A simple circuit can be used to convert the change in conductivity into an output signal corresponding to the gas concentration.
– The MQ-4 gas sensor has high sensitivity to butane, propane and methane, and has a good balance between methane and propane.
– This sensor detects a wide range of flammable gases, especially natural gas, and is a low cost sensor for a variety of applications.
– Suitable for monitoring equipment for liquefied gases, natural gas and gas in the home or industry. Excellent resistance to ethanol and smoke.
Features
1. It adopts high quality double panel design with power indication and TTL signal output indication;
2. It has DO switch signal (TTL) output and AO analog signal output;
3. The TTL output valid signal is low. (When the output is low, the signal light is on, it can be directly connected to the MCU or relay module)
4. The voltage of the analog output, the higher the concentration, the higher the voltage.
5. It has good sensitivity to gas and natural gas detection.
6. there are four screw holes for easy positioning;
7. product dimensions:32 (L) * 20 (W) * 22 (H)
8. has a long service life and reliable stability
9. fast response recovery characteristics
Electrical Performance
Dection of gas:Natural gas/Methane
Dection of Concentration:300-10000ppm
Input voltage:DC5V
Power consumption (current):150mA
DO output:TTL digital quantities 0 and 1 (0.1 and 5V)
AO output:0.1-0.3V (relatively non-polluting), the highest concentration voltage is about 4V
Using the chip:AT89S52
Crystal:11.0592MHZ
Baud rate:9600
Compilation environment:Keil
Special Reminder
After the sensor is energized, it needs to be preheated for about 20S, and the measured data is stable. The heating of the sensor is a normal phenomenon, because there is a heating wire inside, if it is hot, it is not normal.
Package Included
5 x MQ-4 Gas Sensor Module
Weight | 0.035 kg |
---|
Customers Also Viewed
LED Cool Light Egg Candler Tester Ultra Bright Pocket Poultry Egg Lamp incubator
$56.69Switch AccessoriesAdd to cartFeatures– Made of high quality ABS material, insulating, stable and durable.– LED lamp head, high power, strong light source, can clearly detect the hatching of eggs.– Using high-quality materials, safe and durable, with buttons that are easy to open and close.– Suitable for hatching eggs, but also for children and students to learn the process …
LED Cool Light Egg Candler Tester Ultra Bright Pocket Poultry Egg Lamp incubatorRead More
5pcs 2 Channel PWM Generator Module Pulse Frequency Duty Cycle Adjustable
$34.82Other Module BoardAdd to cartProduct Introduction1. Operating Voltage:5-30V,support micro USB 5.0V power supply2. Frequency Range:1Hz~150KHz3. Frequency Precision:2%4. Signal Load Capacity:output current is within 8–30mA5. Output Range:default 5V V-pp (can be changed by external power)6. Ambient Temperature:-30 Celsius ~70 Celsius Application Fields1. As square wave generator to generate square wave for experiment development2. Used to drive steeping motor driver’s square …
5pcs 2 Channel PWM Generator Module Pulse Frequency Duty Cycle AdjustableRead More
3.7V Lithium Battery 4 Paragraph Power indicator Module
$4.36Test & Measuring ModuleAdd to cartDescription1, onboard high precision voltage detection chip and power supply voltage chip2, onboard four power indicator LED lights, three kinds of color display, red, yellow, yellow, green,representing 20%, 50%, 80%, 100% of the battery3, set aside a battery testing interface and two positioning hole4, PCB size:22.2 (mm) x17.2 (mm)Package included1 x 3.7V Lithium Battery 4 …
3.7V Lithium Battery 4 Paragraph Power indicator ModuleRead More
YAHBOOM High-quality T-shape Expansion Board + 40Pin GPIO Flat Rainbow Ribbon Cable for Raspberry 4B/3B+/ZERO/W
$10.21Raspberry Pi & Orange PiAdd to cartDescriptionThis high-quality T-shape expansion board allows you to connect the Raspberry Pi GPIO port for breadboard experiments. We will provide a 40Pin soft cable for you to connect the Raspberry Pi board to the breadboard.FeaturesSpecifically designed for Raspberry Pi 4B/3B, Raspberry Pi 2B, Raspberry Pi 1B+, Raspberry pi 1A+, Raspberry Pi zero W, Raspberry Pi …
10pcs LM3915 10-segment Audio Level indicator Kit Electronic Soldering Training experiment DIY Parts
$33.89DIY Electronic KitsAdd to cartFeatrurePower supply:DC9-12VPCB size:62*27mm1 audio cable is needed. One end is subtracted and connected to the audio input port. The red cable is connected to AUDIO +, the green cable is connected to ADUIO-, and the blue cable is subtracted, do not need to solder.Package included10 x LM3915 10-segment Audio Level Indicator Kit
10pcs 40x40mm thermoelectric Power Generator Peltier Module TEG High Temperature 150 Degree
$55.12Electronic Accessories & SuppliesAdd to cartFeatureColding side posts with the wordsHeating side is emptyRed wire to positive, black wire to the negative, it generate electricity when the temperature difference happenedSpecificationModel:SP1848-27145 Color:whiteLead Length:about 30CMSize:40MM x 40MM x 3.4MM20 degree temperature difference:open-circuit voltage 0.97V, generated current:225MA40 degree temperature difference:open circuit voltage 1.8V, generated current:368MA60 degree temperature difference:open circuit voltage 2.4V, generated current:469MA80 …
10pcs 40x40mm thermoelectric Power Generator Peltier Module TEG High Temperature 150 DegreeRead More
Reviews
There are no reviews yet.