3Pcs J03 LED Digital Time Delay Relay DC 6-30V on off Trigger Delay Timming Timer Switch Micro USB Power Supply 5V 12V
$32.79
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Features
1. Wide voltage power supply (6 ~ 30V), supports microUSB 5.0V power supply, easy to use;
2. The interface is clear and simple, powerful, easy to understand, meet almost all your needs;
3. The emergency stop function (“STOP’key);With reverse polarity protection, reverse polarity will not burn the product.
4. Increase the sleep mode, if this mode is enabled, without any operation within 5 minutes, then automatically turn off the monitor, any key wake-up;
5. You can set a different OP, CL, LOP parameters, which are independent of each other, and are automatically saved;
6. After the module is powered down, all parameter settings are not lost.
Product parameters
1:Operating voltage:6–30V, support microUSB 5.0V power supply
2:Trigger Source:Active-high (3.0V-24V), have optocoupler isolation, can improve the system’s anti-jamming capability (customers can also shorting common ground).
3:Output capability:You can control the DC 30VDC 5A or 220VAC 5A device.
4:Quiescent Current:20mA; Operating Current:50mA
5:Life:more than 10 million times; Working temperature:-40→-85 →; Size:6.2*3.8*1.7cm.
6:With optocoupler isolation, enhanced anti-jamming capability, industrial grade board.
Special Note:The relay outputs are passive contact, just a switch.
Operating mode
P1:trigger signal, the relay is on ‘OP’ time, and then disconnect; in the ‘OP’ time, as follows
P1.1:signal is triggered again, invalid
P1.2:signal is triggered again, the clock is reset
P1.3:Signal trigger again, relay off, stop the clock;
P-2:trigger signal, the relay off ‘CL’ of time, the relay on ‘OP’ time, and then disconnect relay;
P3.1:trigger signal, the relay is turned on after the ‘OP’ time, the relay off ‘CL’ time, then the operation cycle, if the trigger signal period, the relay off, stop the clock; the number of cycles ( ‘LOP ‘) can be set.
P3.2:without triggering signal, the relay is on ‘OP’ time, the relay off ‘CL’ time, and has been cycling; frequency ( ‘LOP’) cycle can be set;
P-4:signal holding function. If there is a trigger signal timing is cleared, the relay remains on; when the signal disappears, after the timing ‘OP’ time, the relay is; if another signal during timing, timing is cleared.
Timing range
0.1 seconds (min) to 999 minutes (max) continuously adjustable
How to choose the time range
After setting the mode selection screen parameter value by a short press ‘STOP’ button to select the time range;
XXX. decimal point in the unit place, time range:1 second to 999 seconds.
XX. X decimal point in decade place, Timing range:0.1 seconds to 99.9 seconds
X. X. X. decimal full brightness, Timing range:1 minute to 999 minutes.
For example, you want to set ‘OP’ is 3.2 seconds, then move the decimal point to decade place, the digital display 03.2
Parameter description:’OP’ – conduction time, ‘CL’ – off time, ‘LOP’ – the number of cycles (1-999 times, ‘—‘ represents infinite loop).
These parameters are independent of each other, but is shared by each mode. For example, in P1.1 mode, set the on-time ‘OP’ is 5 seconds, if you switch to P1.2 mode, it’s ‘OP’ will be 5 seconds too.
In the main interface (display 000), short press ‘SET’ button will display ‘OP’ ( ‘CL’, ‘LOP’) and the corresponding time XXX;
Some parameters only mode ‘OP’ (such as the mode P1.1, P1.2, P1.3), short press the ‘SET’ key to display only the “OP” and the corresponding time;
Some models have parameters ‘OP’,’CL’, ‘LOP’ (such as the mode P3.1, P3.2), short press ‘SET’ button will display ‘OP’ and the corresponding time, “CL” and the corresponding time, “LOP” and the corresponding number of times;
In the main interface by short press ‘SET’ key to see information about the parameters of the current mode, very convenient!
How to set parameters
1. First, read the instructions to determine the required operating mode.
2. The module is powered up, the display at the current work mode (P1.1 default mode), then enter the main interface; press ‘SET’ button for 2 seconds after release to enter mode selection interface; a short time by pressing ‘UP’, ‘DOWN’ key to select the mode (P1.1 ~ P-4).
3. Select the mode (such as P3.2), short press the ‘SET’ button, then the parameter to be set flashes ( ‘OP’on-time, ‘CL’ off time, ‘LOP’ cycles ( ‘—‘ represents infinite loop)), by ‘UP’, ‘DOWN’ keys to adjust the parameter value, support long press (rapid increase or decrease) and short press (increase or decrease one unit); then short press the ‘STOP’ key to select the decimal point position, select the time range (0.1 seconds to 999 minutes); short press the ‘SET’ button to set the next parameters of the current mode of procedure is as above.
4. After the parameters are set, long press ‘SET’ button for 2 seconds then release, the name of the current mode will flash once, and then return to the main screen, set the parameters of success!
The main interface:In the relay does not work status display ‘000’ (no decimal point), with a decimal point under relay state.
Mode selection screen:Long press the ‘SET’ key to enter, after setting is completed, long press the ‘SET’ key to exit back to the main screen.
‘STOP’ button extensions
Relays enable mode
1. ON:Relay allows conduction in the ‘OP’ on-time;
2. OFF:relay prohibit conduction is always closed;
In the main interface, short press the ‘STOP’ button to switch between ON and OFF, the current in which the state will flash, and then return to the main screen. (This feature is an emergency stop function, click off the relay)
Sleep mode
1. ‘C-P’ Sleep mode:five minutes without any operation, the digital display automatically turns off, the program running as usual;
2. ‘O-d’ normal mode:digital display always open;
Press the ‘STOP’ button for two seconds and then release to switch ‘C-P’ and ‘O-d’ state, in which the current state of flashes and then return to the main screen.
Package Included
3 x DC 1 Channel Time Delay Relay Module
3 x Shell Case
Weight | 0.222 kg |
---|
Customers Also Viewed
3pcs L298N Motor Driver Module 4 Chaneel Motor Drive Smart Car Module
$41.54Driver ModuleAdd to cartDescriptionThe four channel L298N motor drive module integrates two L298N chips and can drive four DC motors to realize the control of forward and backward rotation and motor speed. The module is equipped with LM2596S step-down chip. If the motor with 7V voltage or more is driven, 5V power can be output to the control …
3pcs L298N Motor Driver Module 4 Chaneel Motor Drive Smart Car ModuleRead More
Geekcreit D1 Mini ESP32 ESP-32 WiFi+bluetooth internet of Things Development Board Based ESP8266 Module
$21.86Motherboard & Development BoardAdd to cartMore informations:https://github.com/LilyGO/ESP32-MINI-32-V2.0DescriptionThis is D1 Mini ESP32 ESP-32 WiFi+bluetooth Internet Of Things Development Board.Use exampleit can also match the next productPackage included4 x Long female pins4 x short female pins4 x Normal pins1 x mini D1 ESP32
AF1020 Dust-proof Probe Super-stable Pipe-type Current-type Temperature and Humidity Transmitter Temperature Senor Humidity Sensor
$176.16Solar CollectorsAdd to cartSpecificationModel:AF1020 Type Temperature and Humidity TransmitterTemperature measurement range:- 40 ~+80 (℃)Measurement accuracy:+-0.5 (℃)Working Voltage 15-36 (V)Humidity accuracy:+-3% RHHumidity measurement range:0-99.9% RHCurrent output:4-20 m AInstructions1. Power cord positive DC18~36V (red wire)2. Power ground wire GND (black wire)3. Humidity current output 4~20MA (yellow line)4. Temperature current output 4~20MA (white line)Installation sequence1. Connect the red, black, yellow and …
3Pcs 5M Meter thermometer Electronic Digital Display FY10 Embedded thermometer indoor and Outdoor Temperature Measurement
$20.72Test & Measuring ModuleAdd to cartFunction introductionOverall size:48*28*15mmInserted hole size:46*27mmLCD temperature display-50→ to 110→ temperature measurement, 0.1 degree resolution.C and F display versions are availableStandard 0.8m waterproof probeCable length:5 meterPackage includes3 x Thermometer
Peacefair PZEM-028 AC Digital Multifunction Meter Voltmeter Ammeter 0~100A/400V Power Factor Meter
$27.97Electronic Accessories & SuppliesAdd to cartError adjustmentThe product is 100% calibrated before leaving the factory, and the user can also manually adjust the error by himself. The method is as followsStep 1:Long press the button (about 3 seconds) until the digital digit on the screen flashes, then release the button;Step 2:Digital flashing means entering the error adjustment state, the digits …
3pcs 433MHz RF Wireless Receiver Module Transmitter kit + 2PCS RF Spring Antenna OPEN-SMART for Arduino – products that work with official for Arduino boards
$12.11Smart ModuleAdd to cartSize ConversionInchesCentimetersPlease according to your own measurements to choose your suitable size. The tags inside the items will show in our Asian (Type) size.DescriptionThe kit includes one pair of transmitter and receiver modules and one pair of spring antennas for increasing the communication distance. And the frequency is 433MHz. It is very popular for remote …
10pcs DC 3.7-6V To 400KV Boost Step Up Power Module High Voltage Generator
$55.81Power Supply ModuleAdd to cartFeatureThe high-voltage module uses the principle Tesla coil is made of high-voltage pulse output voltage current, small size, high efficiency, simple external circuit(just plug in the switch, the battery can be) discharge intensity violent.SpecificationModel:MC-105Volume:Length 65mm Diameter 24mm, Diameter of cut surface 22mmVoltage:Input DC3.7-6V, output DC200-400KVCurrent:Input 4A, output 0.5ALength:Input 10 cm or so, the output is …
10pcs DC 3.7-6V To 400KV Boost Step Up Power Module High Voltage GeneratorRead More
Reviews
There are no reviews yet.