3Pcs J03 LED Digital Time Delay Relay DC 6-30V on off Trigger Delay Timming Timer Switch Micro USB Power Supply 5V 12V
$32.79
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Features
1. Wide voltage power supply (6 ~ 30V), supports microUSB 5.0V power supply, easy to use;
2. The interface is clear and simple, powerful, easy to understand, meet almost all your needs;
3. The emergency stop function (“STOP’key);With reverse polarity protection, reverse polarity will not burn the product.
4. Increase the sleep mode, if this mode is enabled, without any operation within 5 minutes, then automatically turn off the monitor, any key wake-up;
5. You can set a different OP, CL, LOP parameters, which are independent of each other, and are automatically saved;
6. After the module is powered down, all parameter settings are not lost.
Product parameters
1:Operating voltage:6–30V, support microUSB 5.0V power supply
2:Trigger Source:Active-high (3.0V-24V), have optocoupler isolation, can improve the system’s anti-jamming capability (customers can also shorting common ground).
3:Output capability:You can control the DC 30VDC 5A or 220VAC 5A device.
4:Quiescent Current:20mA; Operating Current:50mA
5:Life:more than 10 million times; Working temperature:-40→-85 →; Size:6.2*3.8*1.7cm.
6:With optocoupler isolation, enhanced anti-jamming capability, industrial grade board.
Special Note:The relay outputs are passive contact, just a switch.
Operating mode
P1:trigger signal, the relay is on ‘OP’ time, and then disconnect; in the ‘OP’ time, as follows
P1.1:signal is triggered again, invalid
P1.2:signal is triggered again, the clock is reset
P1.3:Signal trigger again, relay off, stop the clock;
P-2:trigger signal, the relay off ‘CL’ of time, the relay on ‘OP’ time, and then disconnect relay;
P3.1:trigger signal, the relay is turned on after the ‘OP’ time, the relay off ‘CL’ time, then the operation cycle, if the trigger signal period, the relay off, stop the clock; the number of cycles ( ‘LOP ‘) can be set.
P3.2:without triggering signal, the relay is on ‘OP’ time, the relay off ‘CL’ time, and has been cycling; frequency ( ‘LOP’) cycle can be set;
P-4:signal holding function. If there is a trigger signal timing is cleared, the relay remains on; when the signal disappears, after the timing ‘OP’ time, the relay is; if another signal during timing, timing is cleared.
Timing range
0.1 seconds (min) to 999 minutes (max) continuously adjustable
How to choose the time range
After setting the mode selection screen parameter value by a short press ‘STOP’ button to select the time range;
XXX. decimal point in the unit place, time range:1 second to 999 seconds.
XX. X decimal point in decade place, Timing range:0.1 seconds to 99.9 seconds
X. X. X. decimal full brightness, Timing range:1 minute to 999 minutes.
For example, you want to set ‘OP’ is 3.2 seconds, then move the decimal point to decade place, the digital display 03.2
Parameter description:’OP’ – conduction time, ‘CL’ – off time, ‘LOP’ – the number of cycles (1-999 times, ‘—‘ represents infinite loop).
These parameters are independent of each other, but is shared by each mode. For example, in P1.1 mode, set the on-time ‘OP’ is 5 seconds, if you switch to P1.2 mode, it’s ‘OP’ will be 5 seconds too.
In the main interface (display 000), short press ‘SET’ button will display ‘OP’ ( ‘CL’, ‘LOP’) and the corresponding time XXX;
Some parameters only mode ‘OP’ (such as the mode P1.1, P1.2, P1.3), short press the ‘SET’ key to display only the “OP” and the corresponding time;
Some models have parameters ‘OP’,’CL’, ‘LOP’ (such as the mode P3.1, P3.2), short press ‘SET’ button will display ‘OP’ and the corresponding time, “CL” and the corresponding time, “LOP” and the corresponding number of times;
In the main interface by short press ‘SET’ key to see information about the parameters of the current mode, very convenient!
How to set parameters
1. First, read the instructions to determine the required operating mode.
2. The module is powered up, the display at the current work mode (P1.1 default mode), then enter the main interface; press ‘SET’ button for 2 seconds after release to enter mode selection interface; a short time by pressing ‘UP’, ‘DOWN’ key to select the mode (P1.1 ~ P-4).
3. Select the mode (such as P3.2), short press the ‘SET’ button, then the parameter to be set flashes ( ‘OP’on-time, ‘CL’ off time, ‘LOP’ cycles ( ‘—‘ represents infinite loop)), by ‘UP’, ‘DOWN’ keys to adjust the parameter value, support long press (rapid increase or decrease) and short press (increase or decrease one unit); then short press the ‘STOP’ key to select the decimal point position, select the time range (0.1 seconds to 999 minutes); short press the ‘SET’ button to set the next parameters of the current mode of procedure is as above.
4. After the parameters are set, long press ‘SET’ button for 2 seconds then release, the name of the current mode will flash once, and then return to the main screen, set the parameters of success!
The main interface:In the relay does not work status display ‘000’ (no decimal point), with a decimal point under relay state.
Mode selection screen:Long press the ‘SET’ key to enter, after setting is completed, long press the ‘SET’ key to exit back to the main screen.
‘STOP’ button extensions
Relays enable mode
1. ON:Relay allows conduction in the ‘OP’ on-time;
2. OFF:relay prohibit conduction is always closed;
In the main interface, short press the ‘STOP’ button to switch between ON and OFF, the current in which the state will flash, and then return to the main screen. (This feature is an emergency stop function, click off the relay)
Sleep mode
1. ‘C-P’ Sleep mode:five minutes without any operation, the digital display automatically turns off, the program running as usual;
2. ‘O-d’ normal mode:digital display always open;
Press the ‘STOP’ button for two seconds and then release to switch ‘C-P’ and ‘O-d’ state, in which the current state of flashes and then return to the main screen.
Package Included
3 x DC 1 Channel Time Delay Relay Module
3 x Shell Case
Weight | 0.222 kg |
---|
Customers Also Viewed
EraClean Smart Control Ultrasonic Cleaner 45000Hz High Frequency Vibration Jewelry Eyeglasses Cleaner 360 Cleaning Machine From You Pin
$80.99Laboratory Heating EquipmentsAdd to cartDear Customer,Thank you for supporting, the orders will be shipped before 10st Nov.Hope your kindly understanding and support. Thank you:)Description[New Release] EraClean Mini Ultrasonic Cleaner from XIAOMI ECO Brand System, Quality Guaranteed, With Mute Quiet Design, Cleaning Anything You Want in 3 Minutes.Smart Control Ultrasonic Cleaner 45000Hz High Frequency Vibration Jewelry Eyeglasses Cleaner 360° Thoroughly …
DIY 12V 420W 6-Chip Semiconductor Refrigeration Cooling Device thermoelectric Cooler Air Conditioning High Cooling Efficiency
$129.99Electronic Accessories & SuppliesAdd to cartDescriptionName:420W 6-Chip Semiconductor Air-Conditioning DIY Radiator KitMaterial:metalSize:160*60*60mmVoltage:12VPower:420W( 6-Chip) In the case of 15.4VElectric current:36ASteady current:27ARed line:inch+inch , Black line:inch-inchRefrigeration effect depends on the size of the cooling space, ambient temperature, heat insulation, sealability ,etc…UseSmall space cooling, learning the principle of semiconductor refrigeration, the company developed cooling equipment research, pet air-conditioning, etc., use to cool down …
Lampow LP-9027 DC 12V 24V Waterproof Mirror Touch Sensor Control Switch for LED Strip Light
$15.30Electronic Accessories & SuppliesAdd to cartDescriptionType:LP-9027Output Mode:Sensor output, input is outputSwitch mode:touch sensor on/off switchInstallation:recessed installationWaterproofLightweight and compact sizeEasy to install, stable, long lifeApplication:LED light, LED strip, cabinet kitchen light, kinds of electric applicationsSpecificationsMaterial:Plastic+MetalColor:WhiteVoltage:12-24VOutput Current:3AQuiescent CurrentService time:> 80000hWorking Temperature:-20-50°Hole Diameter:17mmCable Length:0.5m(Output) 1.5m(Input)Size:19*11mmPackage included1 x Touch Sensor Control Switch
M5StickC ESP32 PICO Color LCD Mini IoT Development Board Finger Computer + Expansion Board Prototyping for M5StickC ESP32 Mini IoT Development Board Finger Computer
$42.47Motherboard & Development BoardAdd to cartSize ConversionInchesCentimetersPlease according to your own measurements to choose your suitable size. The tags inside the items will show in our Asian (Type) size.This is without watch accessories,If you like with watch accessories>>>with watch accessories:Click here to BUY>>>More M5Stack Item:Click here to openDescriptionM5Stick is a mini M5Stack, powered by ESP32. It is a portable, easy-to-use, …
PAJ7620U2 Gesture Recognition Sensor Module DIY IIC 9 Gesture Recognition Controller Board
$16.71Sensor & Detector ModuleAdd to cart>>>Manual:Click here to open Overview 1. This is a gesture recognition sensor based on PAJ7620U2. It can recognize 9 different gestures including up, down, left, right, front, back, clockwise, counterclockwise, and swing. 2. The gesture recognition module uses the I2C interface and it use the corresponding library function to program and control. The signal returned …
PAJ7620U2 Gesture Recognition Sensor Module DIY IIC 9 Gesture Recognition Controller BoardRead More
5Pcs Magnetic Field Antenna Large EMC EMI Near Field Probe Conduction
$39.35RF amplifierAdd to cartFeature1. Magnetic field extra large probeInterface:SMA outer screw inner holeProduct size:110*45.5MMProduct weight 8 grams2. Magnetic field large probeInterface:SMA outer screw inner holeProduct size:110*30MMProduct weight 8 grams3. Magnetic field medium probeInterface:SMA outer screw inner holeProduct size:110*20MMProduct weight 6 grams4. Small magnetic field probeInterface:SMA outer screw inner holeProduct size:110*12.5MMProduct weight 6 grams5. Electric field probeInterface:SMA outer screw …
5Pcs Magnetic Field Antenna Large EMC EMI Near Field Probe ConductionRead More
Reviews
There are no reviews yet.