3Pcs J03 LED Digital Time Delay Relay DC 6-30V on off Trigger Delay Timming Timer Switch Micro USB Power Supply 5V 12V
$32.79
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Features
1. Wide voltage power supply (6 ~ 30V), supports microUSB 5.0V power supply, easy to use;
2. The interface is clear and simple, powerful, easy to understand, meet almost all your needs;
3. The emergency stop function (“STOP’key);With reverse polarity protection, reverse polarity will not burn the product.
4. Increase the sleep mode, if this mode is enabled, without any operation within 5 minutes, then automatically turn off the monitor, any key wake-up;
5. You can set a different OP, CL, LOP parameters, which are independent of each other, and are automatically saved;
6. After the module is powered down, all parameter settings are not lost.
Product parameters
1:Operating voltage:6–30V, support microUSB 5.0V power supply
2:Trigger Source:Active-high (3.0V-24V), have optocoupler isolation, can improve the system’s anti-jamming capability (customers can also shorting common ground).
3:Output capability:You can control the DC 30VDC 5A or 220VAC 5A device.
4:Quiescent Current:20mA; Operating Current:50mA
5:Life:more than 10 million times; Working temperature:-40→-85 →; Size:6.2*3.8*1.7cm.
6:With optocoupler isolation, enhanced anti-jamming capability, industrial grade board.
Special Note:The relay outputs are passive contact, just a switch.
Operating mode
P1:trigger signal, the relay is on ‘OP’ time, and then disconnect; in the ‘OP’ time, as follows
P1.1:signal is triggered again, invalid
P1.2:signal is triggered again, the clock is reset
P1.3:Signal trigger again, relay off, stop the clock;
P-2:trigger signal, the relay off ‘CL’ of time, the relay on ‘OP’ time, and then disconnect relay;
P3.1:trigger signal, the relay is turned on after the ‘OP’ time, the relay off ‘CL’ time, then the operation cycle, if the trigger signal period, the relay off, stop the clock; the number of cycles ( ‘LOP ‘) can be set.
P3.2:without triggering signal, the relay is on ‘OP’ time, the relay off ‘CL’ time, and has been cycling; frequency ( ‘LOP’) cycle can be set;
P-4:signal holding function. If there is a trigger signal timing is cleared, the relay remains on; when the signal disappears, after the timing ‘OP’ time, the relay is; if another signal during timing, timing is cleared.
Timing range
0.1 seconds (min) to 999 minutes (max) continuously adjustable
How to choose the time range
After setting the mode selection screen parameter value by a short press ‘STOP’ button to select the time range;
XXX. decimal point in the unit place, time range:1 second to 999 seconds.
XX. X decimal point in decade place, Timing range:0.1 seconds to 99.9 seconds
X. X. X. decimal full brightness, Timing range:1 minute to 999 minutes.
For example, you want to set ‘OP’ is 3.2 seconds, then move the decimal point to decade place, the digital display 03.2
Parameter description:’OP’ – conduction time, ‘CL’ – off time, ‘LOP’ – the number of cycles (1-999 times, ‘—‘ represents infinite loop).
These parameters are independent of each other, but is shared by each mode. For example, in P1.1 mode, set the on-time ‘OP’ is 5 seconds, if you switch to P1.2 mode, it’s ‘OP’ will be 5 seconds too.
In the main interface (display 000), short press ‘SET’ button will display ‘OP’ ( ‘CL’, ‘LOP’) and the corresponding time XXX;
Some parameters only mode ‘OP’ (such as the mode P1.1, P1.2, P1.3), short press the ‘SET’ key to display only the “OP” and the corresponding time;
Some models have parameters ‘OP’,’CL’, ‘LOP’ (such as the mode P3.1, P3.2), short press ‘SET’ button will display ‘OP’ and the corresponding time, “CL” and the corresponding time, “LOP” and the corresponding number of times;
In the main interface by short press ‘SET’ key to see information about the parameters of the current mode, very convenient!
How to set parameters
1. First, read the instructions to determine the required operating mode.
2. The module is powered up, the display at the current work mode (P1.1 default mode), then enter the main interface; press ‘SET’ button for 2 seconds after release to enter mode selection interface; a short time by pressing ‘UP’, ‘DOWN’ key to select the mode (P1.1 ~ P-4).
3. Select the mode (such as P3.2), short press the ‘SET’ button, then the parameter to be set flashes ( ‘OP’on-time, ‘CL’ off time, ‘LOP’ cycles ( ‘—‘ represents infinite loop)), by ‘UP’, ‘DOWN’ keys to adjust the parameter value, support long press (rapid increase or decrease) and short press (increase or decrease one unit); then short press the ‘STOP’ key to select the decimal point position, select the time range (0.1 seconds to 999 minutes); short press the ‘SET’ button to set the next parameters of the current mode of procedure is as above.
4. After the parameters are set, long press ‘SET’ button for 2 seconds then release, the name of the current mode will flash once, and then return to the main screen, set the parameters of success!
The main interface:In the relay does not work status display ‘000’ (no decimal point), with a decimal point under relay state.
Mode selection screen:Long press the ‘SET’ key to enter, after setting is completed, long press the ‘SET’ key to exit back to the main screen.
‘STOP’ button extensions
Relays enable mode
1. ON:Relay allows conduction in the ‘OP’ on-time;
2. OFF:relay prohibit conduction is always closed;
In the main interface, short press the ‘STOP’ button to switch between ON and OFF, the current in which the state will flash, and then return to the main screen. (This feature is an emergency stop function, click off the relay)
Sleep mode
1. ‘C-P’ Sleep mode:five minutes without any operation, the digital display automatically turns off, the program running as usual;
2. ‘O-d’ normal mode:digital display always open;
Press the ‘STOP’ button for two seconds and then release to switch ‘C-P’ and ‘O-d’ state, in which the current state of flashes and then return to the main screen.
Package Included
3 x DC 1 Channel Time Delay Relay Module
3 x Shell Case
Weight | 0.222 kg |
---|
Customers Also Viewed
5Pcs MQ-7 MQ7 Carbon Monoxide CO Gas Sensor Detection Module
$13.49Sensor & Detector ModuleAdd to cart>>>Manual:Click here to openOverviewSensitive material MQ-7 gas sensors used in clean air, low conductivity tin oxide (SnO2). High-low temperature cycling detection mode (1.5V heating) carbon monoxide detector, conductivity sensor with the increasing concentration of carbon monoxide gas in the air increases,high-temperature (5.0V heating) cleaning cryoadsorption stray gases. Using a simple circuit to change the conductivity, …
5Pcs MQ-7 MQ7 Carbon Monoxide CO Gas Sensor Detection ModuleRead More
Mini DC12V 3M Micro Quiet Motor Submersible Brushless Water Pump
$24.29Electrical Pump & ValveAdd to cartDescriptionMini DC 12V 3M 240L/H Micro Quiet Brushless Motor Submersible Water PumpFeatureBrushless, permanent magnetic rotor, maintenance-free.Stator and circuit board sealed by epoxy resin.The axis is enclosed with static sealing, which can avoid leaking problemsAdopt high performance stainless steel shaft.Amphibious design, able to work either on land or in water.Super long working life (more than 30,000 …
Mini DC12V 3M Micro Quiet Motor Submersible Brushless Water PumpRead More
100-240V Power Adapter Power Supply Adaptor Plugs AU Standard
$16.19AC/DC AdaptersAdd to cartPower Supply Adaptor for Makita Radio BMR100 BMR100W BMR102 BMR105 DMR105SpecificationsInput:AC 100-240V, 50/60HzOutput:DC 12V 1AColor:BlackSize(Approximately):7.8*4.9*3.2cm(approx.)Wire length(Approximately):93cmPlug type:AU PlugFeatures-Voltage Protection-Short Circuit Protection-Current Protection-Sealed for protection against moisture and humidityApplicationFor Makita Radio BMR100 BMR100W BMR102 BMR105 DMR105Package included1 x Adaptor
3pcs BT201 Dual Mode 5.0 Bluetooth Lossless Audio Power Amplifier Board Module TF Card U Disk Ble Spp Serial Port Transparent
$16.31Amplifier BoardAdd to cart>>>Manual:Click here to openOverviewBT201 5.0 Bluetooth module is a 4-in-1 single chip that supports bluetooth, usb flash drive and TF card. The highlight of the chip is that it supports lossless music playback, simple and clear serial port control function, BLE pass-through function and SPP pass-through function.It greatly reduces the development difficulty of embedded bluetooth …
100pcs 30pF 5.08MM 50V Multilayer Monolithic Ceramic Capacitor
$5.09Electronic Accessories & SuppliesAdd to cartDescriptionFrequency characteristics:low frequencyAdjustment method:fixedLead Type:Radial Lead WireTolerance:÷ 10 (%)Pressure resistance:50 (V)Capacity:30pFFeaturesLarge capacity, small size, high reliability,Stable capacity, high temperature and humidity resistance.Applications:Widely used in electronic precision instruments.A variety of small electronic equipment for resonance, wave filtering Package included100 x 30pF capacitor
220V 750W Stainless Steel Deep Well Submersible Screw Pump Water Pump
$546.74Electrical Pump & ValveAdd to cartSpecificationsName:Submersible PumpColor:grayMaterials:stainless steelPower:750WVoltage:220VSize:540*100mmCord Length:18mPump Head/Lift:75m MaxFeatures-Energy-efficient, easy to install, low energy, low noise.-Stainless steel body, strong and durable, not easy to rust.-Stainless steel filter prevents impurities from entering the pump and has a long service life.Package Included1 x Submersible Pump3 x Accessories(distribute the adapter according to your country)
20Pcs Mini DC-DC1.3A Voltage Converter Step Down Module 12V 24V to 5V 3.3V 9V with integrated inductor for 360 RC
$31.43Power Supply ModuleAdd to cartFeaturesThe maximum output current is 1.3A, and it is running within 1A for a long time;Non-isolated DC synchronous rectification with up to 94% conversion efficiencyOne-piece inductor, lower heat than ordinary shielded inductorUniversal, optional output voltage, spot welding directly on the boardOutput with LED indicator for easy and visual indication of voltage outputWith enable (EN) port, …
65x37mm Universal Slotted Frame Rail Floor Jack Guard Adapter Lift Rubber Pad Rubber Mat
$22.67RubbersAdd to cartDescriptionThis rubber pad is suitable for car Jack with 55mm intake.SpecificationType:Rubber Pad Universal Diameter 65×37 With Wide V-GrooveMaterial:RubberColor:BlackDiameter:65mmTotal height:37 mmGroove Top:15mmGroove Bottom:10mmGroove Height:8mmFeatures1. Universally applicable.2. Industrial Quality.3. Very robust (min. 80 Shore).4. Easy install and durable use.5. Great quality and great Fitment.6. Direct Replacement, No Modifications Necessary.FitmentSuitable For Car Jack With 55mm IntakePackage Included1 x …
65x37mm Universal Slotted Frame Rail Floor Jack Guard Adapter Lift Rubber Pad Rubber MatRead More
Reviews
There are no reviews yet.