3Pcs J03 LED Digital Time Delay Relay DC 6-30V on off Trigger Delay Timming Timer Switch Micro USB Power Supply 5V 12V
$32.79
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Features
1. Wide voltage power supply (6 ~ 30V), supports microUSB 5.0V power supply, easy to use;
2. The interface is clear and simple, powerful, easy to understand, meet almost all your needs;
3. The emergency stop function (“STOP’key);With reverse polarity protection, reverse polarity will not burn the product.
4. Increase the sleep mode, if this mode is enabled, without any operation within 5 minutes, then automatically turn off the monitor, any key wake-up;
5. You can set a different OP, CL, LOP parameters, which are independent of each other, and are automatically saved;
6. After the module is powered down, all parameter settings are not lost.
Product parameters
1:Operating voltage:6–30V, support microUSB 5.0V power supply
2:Trigger Source:Active-high (3.0V-24V), have optocoupler isolation, can improve the system’s anti-jamming capability (customers can also shorting common ground).
3:Output capability:You can control the DC 30VDC 5A or 220VAC 5A device.
4:Quiescent Current:20mA; Operating Current:50mA
5:Life:more than 10 million times; Working temperature:-40→-85 →; Size:6.2*3.8*1.7cm.
6:With optocoupler isolation, enhanced anti-jamming capability, industrial grade board.
Special Note:The relay outputs are passive contact, just a switch.
Operating mode
P1:trigger signal, the relay is on ‘OP’ time, and then disconnect; in the ‘OP’ time, as follows
P1.1:signal is triggered again, invalid
P1.2:signal is triggered again, the clock is reset
P1.3:Signal trigger again, relay off, stop the clock;
P-2:trigger signal, the relay off ‘CL’ of time, the relay on ‘OP’ time, and then disconnect relay;
P3.1:trigger signal, the relay is turned on after the ‘OP’ time, the relay off ‘CL’ time, then the operation cycle, if the trigger signal period, the relay off, stop the clock; the number of cycles ( ‘LOP ‘) can be set.
P3.2:without triggering signal, the relay is on ‘OP’ time, the relay off ‘CL’ time, and has been cycling; frequency ( ‘LOP’) cycle can be set;
P-4:signal holding function. If there is a trigger signal timing is cleared, the relay remains on; when the signal disappears, after the timing ‘OP’ time, the relay is; if another signal during timing, timing is cleared.
Timing range
0.1 seconds (min) to 999 minutes (max) continuously adjustable
How to choose the time range
After setting the mode selection screen parameter value by a short press ‘STOP’ button to select the time range;
XXX. decimal point in the unit place, time range:1 second to 999 seconds.
XX. X decimal point in decade place, Timing range:0.1 seconds to 99.9 seconds
X. X. X. decimal full brightness, Timing range:1 minute to 999 minutes.
For example, you want to set ‘OP’ is 3.2 seconds, then move the decimal point to decade place, the digital display 03.2
Parameter description:’OP’ – conduction time, ‘CL’ – off time, ‘LOP’ – the number of cycles (1-999 times, ‘—‘ represents infinite loop).
These parameters are independent of each other, but is shared by each mode. For example, in P1.1 mode, set the on-time ‘OP’ is 5 seconds, if you switch to P1.2 mode, it’s ‘OP’ will be 5 seconds too.
In the main interface (display 000), short press ‘SET’ button will display ‘OP’ ( ‘CL’, ‘LOP’) and the corresponding time XXX;
Some parameters only mode ‘OP’ (such as the mode P1.1, P1.2, P1.3), short press the ‘SET’ key to display only the “OP” and the corresponding time;
Some models have parameters ‘OP’,’CL’, ‘LOP’ (such as the mode P3.1, P3.2), short press ‘SET’ button will display ‘OP’ and the corresponding time, “CL” and the corresponding time, “LOP” and the corresponding number of times;
In the main interface by short press ‘SET’ key to see information about the parameters of the current mode, very convenient!
How to set parameters
1. First, read the instructions to determine the required operating mode.
2. The module is powered up, the display at the current work mode (P1.1 default mode), then enter the main interface; press ‘SET’ button for 2 seconds after release to enter mode selection interface; a short time by pressing ‘UP’, ‘DOWN’ key to select the mode (P1.1 ~ P-4).
3. Select the mode (such as P3.2), short press the ‘SET’ button, then the parameter to be set flashes ( ‘OP’on-time, ‘CL’ off time, ‘LOP’ cycles ( ‘—‘ represents infinite loop)), by ‘UP’, ‘DOWN’ keys to adjust the parameter value, support long press (rapid increase or decrease) and short press (increase or decrease one unit); then short press the ‘STOP’ key to select the decimal point position, select the time range (0.1 seconds to 999 minutes); short press the ‘SET’ button to set the next parameters of the current mode of procedure is as above.
4. After the parameters are set, long press ‘SET’ button for 2 seconds then release, the name of the current mode will flash once, and then return to the main screen, set the parameters of success!
The main interface:In the relay does not work status display ‘000’ (no decimal point), with a decimal point under relay state.
Mode selection screen:Long press the ‘SET’ key to enter, after setting is completed, long press the ‘SET’ key to exit back to the main screen.
‘STOP’ button extensions
Relays enable mode
1. ON:Relay allows conduction in the ‘OP’ on-time;
2. OFF:relay prohibit conduction is always closed;
In the main interface, short press the ‘STOP’ button to switch between ON and OFF, the current in which the state will flash, and then return to the main screen. (This feature is an emergency stop function, click off the relay)
Sleep mode
1. ‘C-P’ Sleep mode:five minutes without any operation, the digital display automatically turns off, the program running as usual;
2. ‘O-d’ normal mode:digital display always open;
Press the ‘STOP’ button for two seconds and then release to switch ‘C-P’ and ‘O-d’ state, in which the current state of flashes and then return to the main screen.
Package Included
3 x DC 1 Channel Time Delay Relay Module
3 x Shell Case
Weight | 0.222 kg |
---|
Customers Also Viewed
K202 Low Power Consumption Fingerprint Control Board Switch Fingerprint Access Control Board DC12V
$17.48Other Module BoardAdd to cart>>>Manual:Click here to openSpecifications·P1:Power supply:DC12V·Output:Relay(Max. current:10A)·Standby current:15uA·Fingerprint capacity:120 pieces·Size:64.4*25.4mm·P2:MX 1.0mm space 6 Pin Fingerprint Module(can connect R502,R502-A,R502-AW,R503)·P3:MX 1.25mm space 6 Pin Fingerprint Module(can connect R300,R301T,R303,R303T,R305,R306,R307,R501)K202 is designed for low power consumption, the power supply is DC12V, the relay time can be adjusted by rotating the button, relay time:0.5-13 seconds.It is very easy to register fingerprint, …
intelligent Voice Recognition Module AC108 Audio Decoding Module 4 Microphones Decoder for Smart Speaker DIY
$28.42Expansion Board & ShieldAdd to cartSize ConversionInchesCentimetersPlease according to your own measurements to choose your suitable size. The tags inside the items will show in our Asian (Type) size.Feature1. Based on RASPBERRY PI 40PIN interface, suitable for RASPBERRY PI series motherboards;2. Support RASPBERRY PI ZERO / ZERO W / 2B / 3B / 3B + / 4 and other development …
GP2Y1010AU0F Dust Sensor Module Dust Particle Concentration PM2.5 Haze Detection
$32.79Sensor & Detector ModuleAdd to cartFeaturesEasy to use:only one AD acquisition pin and one control pin are neededAnalog output:The output voltage is linearly related to the dust concentration in the effective range, with a built-in attenuation circuit, the output voltage does not exceed 1.5VSensitivity:0.5V/(100┢g/m3)Effective range:500┢g/m3Wide power supply range:built-in booster circuit, working voltage range 2.5V to 5.5VLow power consumption:within a sampling …
GP2Y1010AU0F Dust Sensor Module Dust Particle Concentration PM2.5 Haze DetectionRead More
3pcs TM1637 4 Bits Digital LED Display Module 7 Segment 0.36 inch RED Anode Tube 4 Serial Driver Board for
$11.00Display ScreenAdd to cartIntroductionThe module is a 12-pin display module with a 4-point common digital tube (0.36 inch) with a clock point. The driver chip is TM1637. It only needs 2 signal lines to enable the MCU to control the 4-bit 8- Segment digital tube.FeaturesDigital Tube:4-digit common anode with a 0.36-inch digital tube with a score point, highlighted …
1080P HDMI Male to 3RCA Audio Video AV Output Transmit Cable Adapter 1.5M/5Feet
$7.86Expansion Board & ShieldAdd to cartFeatures– Gold plated connectors for better signal transfer.– New generic HDMI Male to 3 RCA Audio Video AV Component.– HDMI to RCA cable is designed to connect and transfer signals from HDMI port to RCA port.– High quality HDMI- RCA cable suitable for use in HDTV, Home Theater systems, and all other HDMI to RCA …
1080P HDMI Male to 3RCA Audio Video AV Output Transmit Cable Adapter 1.5M/5FeetRead More
LED Strip Switching Power Supply AC110V-240V to DC12V 60W 5A 160*40*32mm S-60-12
$35.59Power Supply ModuleAdd to cartFeature1. International AC input range2. High efficiency, low working temperature3. Short circuit,overload,over-current protection4. 100% fully load burn-in test5. Built-in EMI filter, low ripple noise6. Low cost, high reliability7. CE and FCC approvalSpecification1. LED switching power supply using pulse width modulation (PWM) switching technology designed to ensure power supply stability and high efficiency. 2. Product interference, …
LED Strip Switching Power Supply AC110V-240V to DC12V 60W 5A 160*40*32mm S-60-12Read More
5pcs TB371 4 Key MCU Keyboard Button Board Compatible UNO MEGA2560 Pro Mini Nano Due for Raspberry Pi Teensy++ Geekcreit for Arduino – products that work with official for Arduino boards
$14.12Other Module BoardAdd to cartSize ConversionInchesCentimetersPlease according to your own measurements to choose your suitable size. The tags inside the items will show in our Asian (Type) size.Description1. 4-button Common Cathode key module(When pressed output low level). 2. GND K1 K2 K3 K4′ 4 PIN OUT 2.54mm3. Working voltage:DC 0-48V 4. Size:12.7 x 33mm5. It can be inserted directly …
TCRT5000 infrared Reflective Switch IR Barrier Line Track Sensor Module
$4.36Sensor & Detector ModuleAdd to cartTCRT5000 Infrared Reflective Switch IR Barrier Line Track Sensor ModuleFeaturesTCRT5000 sensor of infrared emission diode constantly launch infrared, the infrared ray is emitted when the intensity of reflected back has not been reflected or but is not big enough, the light activated triode has been in the off state, the output end of the module …
TCRT5000 infrared Reflective Switch IR Barrier Line Track Sensor ModuleRead More
Reviews
There are no reviews yet.