5pcs Electronic DIY LED Dimming Lights Series and Parallel Circuit Technology Small Production Kit
$16.60
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Description
The purpose of the experiment
1. Understand and recognize the light-emitting diodes and illuminate the light-emitting diodes (LEDs);
2. Understand the role of understanding resistance, series and parallel resistance;
3. Understand the self-locking switch;
4. Understand and recognize adjustable resistors and use adjustable resistors;
Experimental steps
Step 1:The long leg of the light-emitting diode (LED) is the positive pole, and the short leg is the negative pole. First, the long wire of the LED is connected to the black wire (negative electrode) of the battery case, and the short leg of the LED is connected to the red wire (positive electrode) of the battery case. At this time, the light emitting diode (LED) is not lit. Then send it over again, let the long leg of the LED connect to the red line of the battery box, and the short leg of the LED is connected to the black line of the battery box. At this time, the LED lights up, indicating that the LED is in one-way operation and the single-pass characteristic of the diode .
Step 2:In the circuit of the experimental step 1, a resistor of 220 ohms is inserted in series, and the brightness of the LED lamp is lowered, and the resistance hinders the current.
Step 3:Connect a 220 ohm resistor in parallel with the resistance in the circuit of the experimental board 2. The brightness of the LED is increased, indicating that the total resistance of the resistor in the circuit is reduced after the resistors are connected in parallel.
Step 4:Change the two resistors of the experimental step 3 from parallel to series. After the series connection, the brightness of the LED lamp is the lowest. After the series connection of the resistors, the total resistance of the resistor in the circuit increases.
Step 5:Replace the original resistor with a potentiometer. The potentiometer has 3 feet, and the resistance of pins 1 and 3 is fixed. The resistance of pins 1 and 2, 2 feet and 3 feet can be changed by adjusting the potentiometer knob. When experimenting, you can pick up 2 of them. The foot has to experiment many times, adjust the potentiometer knob to observe the change of LED brightness, so that you can fully understand the potentiometer.
Step 6:Know the self-locking. Press and wait for the light to be on, then press the light to turn off.
Package included
5 x DIY LED Dimming Lights Technology Small Production Kit
Weight | 0.135 kg |
---|
Customers Also Viewed
3pcs 6mA 3-100CM Adjustable infrared Digital Obstacle Avoidance Sensor Module
$20.45Sensor & Detector ModuleAdd to cartSpecificationsWorking voltage:DC 3.8V-5.5VWorking current (5V):typical current 6mAInput and output signals (3 lines):GND, VCC is power, and VCC is 3.8V-5.5VObstacle detection time (range from obstacle-free to obstacle-free or obstacle-free to obstacle-free)Working Principle:Sensors actively emit infrared light, according to reflected light detection, if detected obstacles, OUT foot output 0, otherwise 1.Detection distance (test environment, indoor, maximum power, …
3pcs 6mA 3-100CM Adjustable infrared Digital Obstacle Avoidance Sensor ModuleRead More
60x90cm Woven Wire 304 Stainless Steel Filtration Grill Sheet Filter 4 Mesh
$74.87Mesh & Wire ClothAdd to cartDescriptionStainless Steel Woven Wire is widely used in stainless steel mesh screen filter and protectivedecorative, scope throughout the mining, petroleum, chemical, food, medicine, machinerymanufacturing, construction, decoration, electronics, aerospace and other industries.SpecificationMaterial:Stainless steelSize:60x90cmMesh:4Features– Acid and alkali resistance, good corrosion performance; high strength, tensile, toughness and wear resistance, durable;– High temperature oxidation– Normal processing, plastic processing that …
60x90cm Woven Wire 304 Stainless Steel Filtration Grill Sheet Filter 4 MeshRead More
5Pcs 2381BS 0.28 inch LED Digital Tube 3-digit Common Anode Bright Red Light
$5.18Electronic Accessories & SuppliesAdd to cartSpecificationType:0.28inch Three-digit digital tubeDimensions:22.53mm*10mm*7mm (length * width * thickness)Color:Red lightQuantity:5PcsPackage included5Pcs LED Digital Tube
3Pcs 15W TDA7297 Dual-Channel Amplifier Board
$22.42Amplifier BoardAdd to cart3Pcs 15W TDA7297 Dual-Channel Amplifier Board For Features AC / DC, 2.0 / dual channel / stereo,12V/2A when using, the output power of 15W +15 W, peak up 25W +25 W Can be accessed by two 4-8Ω 10-50W speakers A large volume of small size High signal to noise ratio Upgraded version of the radiator, …
5pcs 4S 16.8V BMS PCB 18650 Lithium Battery Charger Protection Board Balanced Current 100mA
$19.95Battery Protection ModuleAdd to cartFeatureName:Lithium battery balancing boardScope of application:3.7V Nominal voltage, 4.2V full voltage lithium battery (including 18650, 26650, polymer lithium battery)Size:20 x 30 x 2.4mmAdaptable voltage:16.8VBalanced current:100mA, suitable for 2000-4000 mah batteryNote:this product cannot be used instead of lithium battery protection board (not overcharge protection and discharge protection function)Package included5 x Lithium battery balancing board
UWB Ultra Wideband Antenna 2.4Ghz – 10.5Ghz Pulse PCB Antenna Module
$17.48Motherboard & Development BoardAdd to cartFeaturesThis is an improved UWB antenna, mainly used for ultra-wideband positioning, communication and so on.The antenna coverage frequency is 2.4GHz-10.5GHz, and the standing wave is usually less than 2.5.The antenna is characterized by small size and high efficiency.Ultra-wideband UWB antenna, high transmission rate.UWB pulse forming technology, a worthwhile antenna for you.SpecificationMaterial:PCBColor:as picture shownWorking frequency:2.4GHz-10.5GHzPolarization mode:vertical …
UWB Ultra Wideband Antenna 2.4Ghz – 10.5Ghz Pulse PCB Antenna ModuleRead More
Reviews
There are no reviews yet.