5pcs Electronic DIY LED Dimming Lights Series and Parallel Circuit Technology Small Production Kit
$16.60
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Description
The purpose of the experiment
1. Understand and recognize the light-emitting diodes and illuminate the light-emitting diodes (LEDs);
2. Understand the role of understanding resistance, series and parallel resistance;
3. Understand the self-locking switch;
4. Understand and recognize adjustable resistors and use adjustable resistors;
Experimental steps
Step 1:The long leg of the light-emitting diode (LED) is the positive pole, and the short leg is the negative pole. First, the long wire of the LED is connected to the black wire (negative electrode) of the battery case, and the short leg of the LED is connected to the red wire (positive electrode) of the battery case. At this time, the light emitting diode (LED) is not lit. Then send it over again, let the long leg of the LED connect to the red line of the battery box, and the short leg of the LED is connected to the black line of the battery box. At this time, the LED lights up, indicating that the LED is in one-way operation and the single-pass characteristic of the diode .
Step 2:In the circuit of the experimental step 1, a resistor of 220 ohms is inserted in series, and the brightness of the LED lamp is lowered, and the resistance hinders the current.
Step 3:Connect a 220 ohm resistor in parallel with the resistance in the circuit of the experimental board 2. The brightness of the LED is increased, indicating that the total resistance of the resistor in the circuit is reduced after the resistors are connected in parallel.
Step 4:Change the two resistors of the experimental step 3 from parallel to series. After the series connection, the brightness of the LED lamp is the lowest. After the series connection of the resistors, the total resistance of the resistor in the circuit increases.
Step 5:Replace the original resistor with a potentiometer. The potentiometer has 3 feet, and the resistance of pins 1 and 3 is fixed. The resistance of pins 1 and 2, 2 feet and 3 feet can be changed by adjusting the potentiometer knob. When experimenting, you can pick up 2 of them. The foot has to experiment many times, adjust the potentiometer knob to observe the change of LED brightness, so that you can fully understand the potentiometer.
Step 6:Know the self-locking. Press and wait for the light to be on, then press the light to turn off.
Package included
5 x DIY LED Dimming Lights Technology Small Production Kit
Weight | 0.135 kg |
---|
Customers Also Viewed
BESTEP 4 Channel 24V Relay Module High And Low Level Trigger for
$10.15Relay ModuleAdd to cartDescription Maximum load:AC 250V/10A, DC 30V/10A. The chip optocoupler isolation, strong driving ability, stable performance, trigger current 5mA. Working voltage is 24V. Every channel of the module can be set up by high jumper or low level trigger. Fault tolerant design, even if the control line is broken, the relay will not act. Power indicator …
BESTEP 4 Channel 24V Relay Module High And Low Level Trigger forRead More
5Pcs CJMCU-3386 MC33186DH1 Automotive Computer Board Idle Speed Throttle Drive Board A H Bridge
$50.91Other Module BoardAdd to cartDescriptionThe 33886 is a monolithic H-Bridge ideal for fractional horsepowerDC-motor and bi-directional thrust solenoid control. The IC incorporatesinternal control logic, charge pump, gate drive, and low RDS(ON) MOSFEToutput circuitry. The 33886 is able to control continuous inductive DC loadcurrents up to 5.0 A. Output loads can be pulse width modulated (PWM-ed)at frequencies up to 10 …
20pcs Light Dependent Resistor LDR 5MM Photoresistor Photoelectric Switch Element Photo Detector 5516
$4.36Module ComponentsAdd to cartSpecificationsModel:5549Voltage(VDC):150Power Consumption(mw):100Ambient Temperature(C):-30~+70Spectral Peak(nm):540Bright Resistance(10Lux)K┯:5-10Response Time(MS):Rise:20 Decline:30Package included20 x Resistor
PWM 20A 12V/24V Auto Solar Panel Solar Charge Controller Battery Charge Adapter LCD USB
$36.44Solar ControllersAdd to cartSpecificationsName:20A 12V/24V LCD Display PWM Solar Panel Charge ControllerModel:C11465Rated voltage:12/24V AUTOCharge current:20ADischarge current:10AMax.PV input power:260W(12V),520W(24V)Max solar input12V battery,the highest 23V24V battery when the highest 46VEqualization:14.2VFloat charge:13.7V (defaul,adjustable)Discharge stop:10.7V(defaul,adjustable)Discharge reconnect:12.6V(defaul,adjustable)Charge reconnect:13VVoltage of open light:Solar panel 8V(Light lights delay)Voltage of close light:Solar panel 8V(Light off delay)USB output:2 way USB output,5V/2A(Max.)Self-consumeOperationg temperature:-35-60℃Color:BlackSize:133.5mmx70mmx35mmFeatureBuild-in industrial micro controller.Big LCD display,all adjustable …
PWM 20A 12V/24V Auto Solar Panel Solar Charge Controller Battery Charge Adapter LCD USBRead More
Waveshare Sensor Expansion Board Supports XBEE Module Compatible for Arduino
$39.35Expansion Board & ShieldAdd to cartDocumentsSchematic:Click here to openSample tutorial:Click here to openWhat do I mainly doArduino is a huge ecosystem. If the Pi interface can be converted to the Arduino standard, it can be connected to a variety of compatible Arduino expansion boards and connected to the Arduino ecosystem to obtain more available resources.I just do this.Basic situationCompatible with …
Waveshare Sensor Expansion Board Supports XBEE Module Compatible for ArduinoRead More
Emakefun DC5V RGB Tricolor Lamp Module 5PIN Anti-reverse Connector Compatible with Lego Jack Fixing
$10.61Sensor & Detector ModuleAdd to cartFeature1. Supply voltage:5V2. Connection method:5PIN anti-reverse connection Dupont line3. Module size:40*22.5mm4. Installation method:M4 screw compatible with Lego jack fixing5. Connection port:PH2.0Package includes1 x RGB Tricolor Lamp Module (the other items are not includes)
Reviews
There are no reviews yet.