3pcs Electronic DIY LED Dimming Lights Series and Parallel Circuit Technology Small Production Kit
$10.56
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Description
The purpose of the experiment
1. Understand and recognize the light-emitting diodes and illuminate the light-emitting diodes (LEDs);
2. Understand the role of understanding resistance, series and parallel resistance;
3. Understand the self-locking switch;
4. Understand and recognize adjustable resistors and use adjustable resistors;
Experimental steps
Step 1:The long leg of the light-emitting diode (LED) is the positive pole, and the short leg is the negative pole. First, the long wire of the LED is connected to the black wire (negative electrode) of the battery case, and the short leg of the LED is connected to the red wire (positive electrode) of the battery case. At this time, the light emitting diode (LED) is not lit. Then send it over again, let the long leg of the LED connect to the red line of the battery box, and the short leg of the LED is connected to the black line of the battery box. At this time, the LED lights up, indicating that the LED is in one-way operation and the single-pass characteristic of the diode .
Step 2:In the circuit of the experimental step 1, a resistor of 220 ohms is inserted in series, and the brightness of the LED lamp is lowered, and the resistance hinders the current.
Step 3:Connect a 220 ohm resistor in parallel with the resistance in the circuit of the experimental board 2. The brightness of the LED is increased, indicating that the total resistance of the resistor in the circuit is reduced after the resistors are connected in parallel.
Step 4:Change the two resistors of the experimental step 3 from parallel to series. After the series connection, the brightness of the LED lamp is the lowest. After the series connection of the resistors, the total resistance of the resistor in the circuit increases.
Step 5:Replace the original resistor with a potentiometer. The potentiometer has 3 feet, and the resistance of pins 1 and 3 is fixed. The resistance of pins 1 and 2, 2 feet and 3 feet can be changed by adjusting the potentiometer knob. When experimenting, you can pick up 2 of them. The foot has to experiment many times, adjust the potentiometer knob to observe the change of LED brightness, so that you can fully understand the potentiometer.
Step 6:Know the self-locking. Press and wait for the light to be on, then press the light to turn off.
Package included
3 x DIY LED Dimming Lights Technology Small Production Kit
Weight | 0.081 kg |
---|
Customers Also Viewed
5Pcs A87 4 Channel Optocoupler Isolation Module High And Low Level Expansion Board
$17.08Other Module BoardAdd to cartDescription 1. Function:Use the low level to control the high level. Such as the use of single-chip 3V or 5V voltage control 9V or 12v voltage. 2. HVCC should not exceed 24V. Output OUT1 / OUT2 / OUT3 / OUT4 output current equal to HVCC / 5.1K, absorption current 500ma. 3. This module uses TLP281 …
5Pcs A87 4 Channel Optocoupler Isolation Module High And Low Level Expansion BoardRead More
3pcs DC 3.3V To 20V 5.8GHz Microwave Radar Sensor intelligent Trigger Sensor Switch Module
$16.24Sensor & Detector ModuleAdd to cartDescriptionIt uses Doppler radar technology, with auto-sensing capabilities to control other product,High sensitivity, sensor distance, reliability, wide angle sensor,Wide supply voltage range and other characteristics. Widely used in lighting situations,anti-theft alarm situations.Features1. microwave sensors using planar antenna and receiving echo.2. The switch is active sensors.3. The sensors emit a high-frequency electromagnetic waves and receives their …
3pcs DC 3.3V To 20V 5.8GHz Microwave Radar Sensor intelligent Trigger Sensor Switch ModuleRead More
24V Air Parking Heater Flame Sensor Igniters Flame Detecter 82306B for Webasto Air top 2000
$70.86Solar CollectorsAdd to cartSpecificationsBrand Name:AutoleaderMaterial:Silicon NitrideOEM:82306BItem weight:11gFeaturesThis product is mainly made of silicon nitride ceramic substrate, with tungsten filament as the heat source, tungsten wire embedded in silicon nitride matrix, via hot-press sintering process to form an organic whole, then through grinding, welding wire, thus made the ignition components.Fitmentfor Webasto Air Top 2000Package Included1x Parking Heater Senser
L293D WiFi Smart Robot Car Motor Driver Expansion Board Dual High Power H Bridge Based on ESP12E
$9.79Expansion Board & ShieldAdd to cartL293D WiFi Smart Robot Car Motor Driver Expansion Board Dual High Power H Bridge Based On ESP12E For Specifications 1. Motor power (VM):4.5 ~ 36V 2. Control power (VIN):4.5V ~ 9V(10V MAX) 3. Provide the shortcut connector (short by VM and VIM), thus can use 4. May use common power source (4.5V~9V) by shorting VM …
220V 1000W Hot Plate Electric Iron Burner Heating Stove Heater Household Laboratory Heating Equipments
$52.64Laboratory Heating EquipmentsAdd to cartSpecificationsType:Electric Stove BurnerPlug Type:EUColor:WhiteVoltage:220VPower:1000WRegulating temperature:5 LevelsMaterial:Stainless Steel + IronSize:14*14*5CM (5.5*5.5*2in)Features– Adopted iron shell, thicken panel, material sturdy and durable to use– Portable single burner with 500 watts of power– Powered by electric, do not need fuel, eco-friendly– Easy-to-use temperature-setting knob for low, medium, or high heat– Provides quick and sustained heat; power indicator light– Single …
Reviews
There are no reviews yet.