3pcs Electronic DIY LED Dimming Lights Series and Parallel Circuit Technology Small Production Kit
$10.56
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Description
The purpose of the experiment
1. Understand and recognize the light-emitting diodes and illuminate the light-emitting diodes (LEDs);
2. Understand the role of understanding resistance, series and parallel resistance;
3. Understand the self-locking switch;
4. Understand and recognize adjustable resistors and use adjustable resistors;
Experimental steps
Step 1:The long leg of the light-emitting diode (LED) is the positive pole, and the short leg is the negative pole. First, the long wire of the LED is connected to the black wire (negative electrode) of the battery case, and the short leg of the LED is connected to the red wire (positive electrode) of the battery case. At this time, the light emitting diode (LED) is not lit. Then send it over again, let the long leg of the LED connect to the red line of the battery box, and the short leg of the LED is connected to the black line of the battery box. At this time, the LED lights up, indicating that the LED is in one-way operation and the single-pass characteristic of the diode .
Step 2:In the circuit of the experimental step 1, a resistor of 220 ohms is inserted in series, and the brightness of the LED lamp is lowered, and the resistance hinders the current.
Step 3:Connect a 220 ohm resistor in parallel with the resistance in the circuit of the experimental board 2. The brightness of the LED is increased, indicating that the total resistance of the resistor in the circuit is reduced after the resistors are connected in parallel.
Step 4:Change the two resistors of the experimental step 3 from parallel to series. After the series connection, the brightness of the LED lamp is the lowest. After the series connection of the resistors, the total resistance of the resistor in the circuit increases.
Step 5:Replace the original resistor with a potentiometer. The potentiometer has 3 feet, and the resistance of pins 1 and 3 is fixed. The resistance of pins 1 and 2, 2 feet and 3 feet can be changed by adjusting the potentiometer knob. When experimenting, you can pick up 2 of them. The foot has to experiment many times, adjust the potentiometer knob to observe the change of LED brightness, so that you can fully understand the potentiometer.
Step 6:Know the self-locking. Press and wait for the light to be on, then press the light to turn off.
Package included
3 x DIY LED Dimming Lights Technology Small Production Kit
Weight | 0.081 kg |
---|
Customers Also Viewed
5pcs ST-LINK V2 Programmer Emulator Mini STLINK Downloader for STM8 / STM32 MCU Development Board
$45.35Test & Measuring ModuleAdd to cartSize ConversionInchesCentimetersPlease according to your own measurements to choose your suitable size. The tags inside the items will show in our Asian (Type) size.Description– Only U disk size and compatible with official ST-LINK V2.– Support official firmware upgrade, support all series of STM8 (SWIM interface), STM32(SWD interface).– Two-channel power output 5V / 3.3V and easier …
5pcs Breadboard Power Supply Module Circuit Test 3.3V 5V Switchable
$24.83Power Supply ModuleAdd to cartDescriptionThe size is exactly the same as most bread plates.Small size, suitable for all kinds of experimental equipment.It has the function of current limiting protection.The interface is popular, and the switching voltage can be switched.Input voltage:5VOutput voltage:5V/3.3V switchableOutput current:less than 500mASize:53 x 11mmPackage Included5 x Power Supply Module
3pcs Audio Speaker Protection Board Amplifier Components DC Protect Kit DIY
$24.37DIY Electronic KitsAdd to cartSpecificationInput voltage:AC12-15 VSize(L*W*H):6x 4 x 2.5 cm (Finished)FeatureWith power on delay (about 3 seconds) and DC protection (control voltage around 1 V)With LED status display, when the protection light, the normal work time offUsing 15 A large current relayWorking voltage aAC 12 to 15 V, need independent power supply.Package includes3 x Double-sided circuit boards 3 …
3pcs Audio Speaker Protection Board Amplifier Components DC Protect Kit DIYRead More
5Pcs AMS1117 3.3V Power Supply Module with DC Socket And Switch
$9.02Power Supply ModuleAdd to cartDescription1. onboard AMS1117-3.3 chip2. onboard DC input voltage range of 4.75 V to 12 V3. the onboard 7 * 7 self-locking switch, convenient to control power supply turned on and off during the test4. the onboard power light, indicating whether the power supply5. 4-way output voltage interface, convenient connection during the test6. The board size:48.5 …
5Pcs AMS1117 3.3V Power Supply Module with DC Socket And SwitchRead More
32Pcs Science Chemical Experiment Demonstration Tools Reagent Alcohol Lamp Full Set Storage Box
$89.79Lab Clamp & StandAdd to cartSpecificationType:Chemical Experiment BoxMaterial:Plastic, GlassFeatures1. High quality materials. Environmentally friendly and durable.2. Deepen understanding:thinking at your own hands can give your child a deeper understanding of knowledge.3. The variety of experimental tools is rich, which can meet different experimental needsPackage IncludedItem:QuantityBlue and Red Cup:2 SetFour Treasure Box:1 PcsAlcohol Lamp:2 PcsDropping Bottle:2 PcsSpray Bottle:1 PcsBule Dropping Bottle:3 …
3Pcs T2310 AC110V 220V Programmable Digital Time Delay Switch Relay T2310 Normally Open Timer Control Module 0-999S/Min/Hour
$32.79Test & Measuring ModuleAdd to cartFeatureIndependent crystal oscillator, more accurate timing1. Convenient direct output wiring2. Add buzzer and audible alarm3. Add pause button to stop urgently5. Start and stop setting mode, provincial conversion, which is more convenient6. Automatically save when power off, run automatically when power on7. Timing units can be set separately, with 36 working combinations8. Timing range:0-999 seconds, …
5pcs 30CM 1M Portable Photosensitive Dry Film for Circuit Photoresist Sheet for Plating Hole Covering Etching for Producing PCB Board
$21.78Electronic Accessories & SuppliesAdd to cartFeaturesUniversal used in producing PCB board, attach on the PCB surface to make it photosensitive.Suitable for electroplating, hole covering and etching.Great hole covering ability.High resolution.Great adaptive capacity to different material.Durable in pH 8.0-8.5 situation.1.5mil dry film fully covers a 0.25inch height hole.Suitable for usual plating bath, no wrinkle or color error.SpecificationWidth:approx. 30 cm/11.81inchLength:approx. 100 cm/39.37inchOperating …
Reviews
There are no reviews yet.