3pcs Electronic DIY LED Dimming Lights Series and Parallel Circuit Technology Small Production Kit
$10.56
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Description
The purpose of the experiment
1. Understand and recognize the light-emitting diodes and illuminate the light-emitting diodes (LEDs);
2. Understand the role of understanding resistance, series and parallel resistance;
3. Understand the self-locking switch;
4. Understand and recognize adjustable resistors and use adjustable resistors;
Experimental steps
Step 1:The long leg of the light-emitting diode (LED) is the positive pole, and the short leg is the negative pole. First, the long wire of the LED is connected to the black wire (negative electrode) of the battery case, and the short leg of the LED is connected to the red wire (positive electrode) of the battery case. At this time, the light emitting diode (LED) is not lit. Then send it over again, let the long leg of the LED connect to the red line of the battery box, and the short leg of the LED is connected to the black line of the battery box. At this time, the LED lights up, indicating that the LED is in one-way operation and the single-pass characteristic of the diode .
Step 2:In the circuit of the experimental step 1, a resistor of 220 ohms is inserted in series, and the brightness of the LED lamp is lowered, and the resistance hinders the current.
Step 3:Connect a 220 ohm resistor in parallel with the resistance in the circuit of the experimental board 2. The brightness of the LED is increased, indicating that the total resistance of the resistor in the circuit is reduced after the resistors are connected in parallel.
Step 4:Change the two resistors of the experimental step 3 from parallel to series. After the series connection, the brightness of the LED lamp is the lowest. After the series connection of the resistors, the total resistance of the resistor in the circuit increases.
Step 5:Replace the original resistor with a potentiometer. The potentiometer has 3 feet, and the resistance of pins 1 and 3 is fixed. The resistance of pins 1 and 2, 2 feet and 3 feet can be changed by adjusting the potentiometer knob. When experimenting, you can pick up 2 of them. The foot has to experiment many times, adjust the potentiometer knob to observe the change of LED brightness, so that you can fully understand the potentiometer.
Step 6:Know the self-locking. Press and wait for the light to be on, then press the light to turn off.
Package included
3 x DIY LED Dimming Lights Technology Small Production Kit
Weight | 0.081 kg |
---|
Customers Also Viewed
200pcs 20cm Male to Male Color Breadboard Jumper Cable Dupont Wire
$16.16Electronic Accessories & SuppliesAdd to cartDescription Durable and reusable Easy to install and use A popular choice for construction or repair Be used for electronic project and Genuine product. Specification Length:20cm Quantity:five row of 40 roots 1p-1p pin male to male header Compatible with 2.54mm spacing pin headers Package includes 200 x male to male jumper wire
3pcs ESP8266 ESP-12S Remote Serial Port WIFI Transceiver Wireless Module
$29.04Smart ModuleAdd to cartDescriptionBased on ESP8266 wifi ICFully compatible with forepast versions ESP-12E, or ESP12FFCC&CE&RoHS all passedLow-power consumptionFurther improved antenna design, better signal performanceCan refer to ESP-12F for other infosPackage included3 x ESP-12S Wireless Module
96Pcs Chicken Plucker Fingers Rubber Poultry Duck Turkey Goose Feather Plucking Glue Stick
$99.21Solar CollectorsAdd to cartFeatures-The glue stick has the advantages of high wear resistance, soft texture, large elasticity, no easy breaking, good hair removal effect, low skin breaking rate and the like.-Widely used in chickens, ducks, geese and other slaughter equipment.SpecificationName:Chicken PluckerMaterial:Nat-rubberColor:Yellow or BlackSizes:20 x 65mmPackage included96 x Chicken Plucker glue stickNoteSilicone products, the edge is expected to belong …
96Pcs Chicken Plucker Fingers Rubber Poultry Duck Turkey Goose Feather Plucking Glue StickRead More
10pcs 1838T infrared Sensor Receiver Module Board Remote Controller IR Sensor with Cable
$31.47Sensor & Detector ModuleAdd to cartFeatures– Can receive standard 38KHz remote control signals by means of programming can decode the remote control signals– Strong ability to resist electromagnetic interference and light– Widely used in stereo, TV, set-top boxes, digital photo frame, car stereo, remote control toys, satellite receivers, hard disk players, air conditioner, heater, electric fan, lighting and other home …
10pcs 1838T infrared Sensor Receiver Module Board Remote Controller IR Sensor with CableRead More
3pcs CC1101-868MHz 2-3.6V RF Low Power UHF Wireless Transceiver Module 1.2K To 500kps 64 Bytes SPI
$29.02Smart ModuleAdd to cartDescriptionThe CC1101-868MHz RF module is low cost and highly integrated UHF transceiver designed for low power wireless applications. These pro certificate modules, operating in the license free 868 MHz ISM band, can be easily integrated into your application, thereby reducing development time and cost.FeaturesLow power UHF wireless transceivers @868MHzSupport FSK, GFSK, ASK/OOK and MSKConfigurable data …
Geekcreit Upgrade DIY EC1515B DS1302 Light Control Rotation LED Electronic Clock Kit Size 81x81x2mm
$13.11DIY Electronic KitsAdd to cartDesign Red digital tube+ Red & Green LED with housing / Design Red digital tube+ Red & Blue LED with housing / Design Red digital tube+ Red & Blue LED without housing / Design Red digital tube+ Red & Green LED without housing / Design Blue digital tube+ Red & G
Reviews
There are no reviews yet.