20pcs Electronic DIY LED Dimming Lights Series and Parallel Circuit Technology Small Production Kit
$54.99
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Description
The purpose of the experiment
1. Understand and recognize the light-emitting diodes and illuminate the light-emitting diodes (LEDs);
2. Understand the role of understanding resistance, series and parallel resistance;
3. Understand the self-locking switch;
4. Understand and recognize adjustable resistors and use adjustable resistors;
Experimental steps
Step 1:The long leg of the light-emitting diode (LED) is the positive pole, and the short leg is the negative pole. First, the long wire of the LED is connected to the black wire (negative electrode) of the battery case, and the short leg of the LED is connected to the red wire (positive electrode) of the battery case. At this time, the light emitting diode (LED) is not lit. Then send it over again, let the long leg of the LED connect to the red line of the battery box, and the short leg of the LED is connected to the black line of the battery box. At this time, the LED lights up, indicating that the LED is in one-way operation and the single-pass characteristic of the diode .
Step 2:In the circuit of the experimental step 1, a resistor of 220 ohms is inserted in series, and the brightness of the LED lamp is lowered, and the resistance hinders the current.
Step 3:Connect a 220 ohm resistor in parallel with the resistance in the circuit of the experimental board 2. The brightness of the LED is increased, indicating that the total resistance of the resistor in the circuit is reduced after the resistors are connected in parallel.
Step 4:Change the two resistors of the experimental step 3 from parallel to series. After the series connection, the brightness of the LED lamp is the lowest. After the series connection of the resistors, the total resistance of the resistor in the circuit increases.
Step 5:Replace the original resistor with a potentiometer. The potentiometer has 3 feet, and the resistance of pins 1 and 3 is fixed. The resistance of pins 1 and 2, 2 feet and 3 feet can be changed by adjusting the potentiometer knob. When experimenting, you can pick up 2 of them. The foot has to experiment many times, adjust the potentiometer knob to observe the change of LED brightness, so that you can fully understand the potentiometer.
Step 6:Know the self-locking. Press and wait for the light to be on, then press the light to turn off.
Package included
20 x DIY LED Dimming Lights Technology Small Production Kit
Weight | 0.54 kg |
---|
Customers Also Viewed
5pcs TS-300B Turbidity Sensor Detection Module Water Quality Tester Washing Machine Turbidity Transduce
$43.93Sensor & Detector ModuleAdd to cartPrincipleTurbidity sensor TS-300B measures the turbidity (counter of suspended matter) in the wash water. Based on the optical principle, the sensor uses the light-emitting diode and phototransistor to receive the specific wavelength to measure the opacity or other substances of dirty water. concentration. By using phototransistors and light-emitting diodes, the light emitted by the sensor …
3Pcs USB Fan Speed Controller Module Reducing Noise Multi-stall Adjustment Governor DC 4-12V
$20.74Motor PWM Speed ControllerAdd to cartFeatures– USB Fan Air Conditioner – Strong winds and weak wind adjust freely – Stepless Speed Regulation – Suitable for the very common 5.0V USB fan on the market Regulation PrincipleThe non-adjustable fan is a 5V direct fan motor,while the two-stall fan is the interior has a step-up circuit board,when placed in the second gear,the …
5pcs JDY-08 BLE bluetooth 4.0 Serial Port Wireless Module Low Power Master-slave Support Airsync i Beacon
$45.12Smart ModuleAdd to cartFeaturesJDY-08 transparent transmission module is based on bluetooth 4.0 protocol standard, working frequency range is 2.4GHZ range, modulation mode is GFSK, large transmission power is 0db, large transmission distance is 80 meters, TICC2541 chip design is adopted, and users can modify device name by AT command. , service UUID, transmit power, pairing password and other …
ADC Module ADS1100 for Analog Signal Capture Converter Compatible M5StickC ESP32 Mini IoT Development Board Fi
$14.74Converter BoardAdd to cartnull Description ADC_HAT is another type of C-HAT specifically design for M5StickC controller. Same as ADC unit, this is an ADC converter component for stickc. Packed with an ADC converter chip ADS1100, which is a fully differential, 16-bit, self-calibrating, A/D converter. Extremely easy to design with and configure, the ADS1100 allows you to obtain precise …
5pcs Mini MP1584EN DC-DC BUCK Adjustable Step Down Module 4.5V-28V input 0.8V-20V Output
$8.94Power Supply ModuleAdd to cartSpecificationsModel:MP1584Name:DC-DC step-down moduleInput Voltage:4.5V ~ 28VOutput voltage:0.8V ~ 20VOutput Current:3A (Max)Conversion efficiency:96% (maximum)Output RippleSwitching frequency:1.5MHz (highest) typically 1MHzOperating Temperature:-45°C ~ +85°CSize:22mm * 17mm (L * W )Application areas:DIY mobile power, monitor power supply, power buggies, camera power supply, car power, communications equipment supply,etc.Packge included5 x Step Down Module
LILYGO TTGO T-Koala ESP32 WiFi and bluetooth Module 4MB Development Board Based on ESP32-WROOM-32 Micro USB
$26.23Smart ModuleAdd to cartFeatureEspressif official ESP32-WROOM-32 moduleLatest ESP32 version:REV14MB FLASHLithium battery interface, 500mA maximum charging currentCompatible with , MicroPythonDefault firmware:latest MicroPythoTechnical specificationsMicrocontroller:ESP-32Board power supply:(USB) 5VSupport battery:Lipo Battery 3.7VWorking voltage:3.3VFlash:4 MbytesLength:78 mmWidth:27 mmWeight:7.8 gramsPackage includes1 x ESP32 WiFi&bluetooth Broad2 x Pin
Reviews
There are no reviews yet.