20pcs Electronic DIY LED Dimming Lights Series and Parallel Circuit Technology Small Production Kit
$54.99
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Description
The purpose of the experiment
1. Understand and recognize the light-emitting diodes and illuminate the light-emitting diodes (LEDs);
2. Understand the role of understanding resistance, series and parallel resistance;
3. Understand the self-locking switch;
4. Understand and recognize adjustable resistors and use adjustable resistors;
Experimental steps
Step 1:The long leg of the light-emitting diode (LED) is the positive pole, and the short leg is the negative pole. First, the long wire of the LED is connected to the black wire (negative electrode) of the battery case, and the short leg of the LED is connected to the red wire (positive electrode) of the battery case. At this time, the light emitting diode (LED) is not lit. Then send it over again, let the long leg of the LED connect to the red line of the battery box, and the short leg of the LED is connected to the black line of the battery box. At this time, the LED lights up, indicating that the LED is in one-way operation and the single-pass characteristic of the diode .
Step 2:In the circuit of the experimental step 1, a resistor of 220 ohms is inserted in series, and the brightness of the LED lamp is lowered, and the resistance hinders the current.
Step 3:Connect a 220 ohm resistor in parallel with the resistance in the circuit of the experimental board 2. The brightness of the LED is increased, indicating that the total resistance of the resistor in the circuit is reduced after the resistors are connected in parallel.
Step 4:Change the two resistors of the experimental step 3 from parallel to series. After the series connection, the brightness of the LED lamp is the lowest. After the series connection of the resistors, the total resistance of the resistor in the circuit increases.
Step 5:Replace the original resistor with a potentiometer. The potentiometer has 3 feet, and the resistance of pins 1 and 3 is fixed. The resistance of pins 1 and 2, 2 feet and 3 feet can be changed by adjusting the potentiometer knob. When experimenting, you can pick up 2 of them. The foot has to experiment many times, adjust the potentiometer knob to observe the change of LED brightness, so that you can fully understand the potentiometer.
Step 6:Know the self-locking. Press and wait for the light to be on, then press the light to turn off.
Package included
20 x DIY LED Dimming Lights Technology Small Production Kit
Weight | 0.54 kg |
---|
Customers Also Viewed
1.8 inch LCD TFT Display Module with PCB Backplane 128X160 SPI Serial Port
$15.30Display ScreenAdd to cartFeatureResolution:128X160Driver IC:ILI9163/ST7735Module with regulator IC supports 3.2V/5V power supplyWith SD card holder, you can do experiments like digital photo frameThe module reserves the Nokia3310/5110 interface, supports the 1602 interface, and directly plugs in and out.IO for streamlined wiring:(only 3 IOs after optimization)1. RST– directly connected to the microcontroller reset signal terminal, this IO can save2. …
1.8 inch LCD TFT Display Module with PCB Backplane 128X160 SPI Serial PortRead More
USB Boost 5V to 1.2V 3.3V 6V 9V 12V 24V Power Supply Module Adjustable Voltage
$10.92Test & Measuring ModuleAdd to cartFeatureInput voltage:3.5V-12VOutput voltage:1.2-24VOutput PowerOutput voltage 1.2V-2V, used within 2WOutput voltage 2V-20V, used within 3WOutput voltage 20V-24V, used within 2.5WOutput power = output voltage x output currentNote:This product is not a high power supply, please use it within the power range.Package includes1 x Power Module
10pcs IR LED infrared Light Board for CCTV Camera Night Vision 30-40M 6*Array LED White 2.5W DC12V
$26.76LED BoardAdd to cartSize ConversionInchesCentimetersPlease according to your own measurements to choose your suitable size. The tags inside the items will show in our Asian (Type) size.Features– High power / Spot Light / Infrared IR LED boards for CCTV cameras night vision.– Driven board & CDS sensor included.– Power supply exceeds DC13V may greatly reduce the LEDs operating …
2500Pcs 2.54mm XH2.54 2p 3p 4 Pin Connector Plug+Straight Needle+Terminal Socket Header Wire Adaptor
$56.09Electronic Accessories & SuppliesAdd to cartDescription2pin = 200 sets3pin = 200 sets4pin = 100 setsPin Connector Terminal:1500 pcs (Please allow 5% deviation)Package included10 x Connector plug kit with box
19PCS DIY Resin Casting Molds Silicone Jewelry Pendant Craft Making Mould Tool
$58.71ConnectorsAdd to cartSpecificationName:Resin Casting MoldsMaterial:SiliconeColor:TransparentFeature-Flexible, resistant to tearing.-Easy to use and clean.-Easy to release.-Durable in use.-Great for jewelry pendant making, earrings, soap making, chocolate making, sugarpaste making.-You can also add some flowers, glitter, colors to make your own art craft gift.Package Included9x Resin Casting Molds (Mold only, NO accessories)10x Wood Sticks
4G Cat.1 LTE IoT Module Full Netcom Ca-01 4G Development Board
$98.40Motherboard & Development BoardAdd to cartDocumentsProduct specification:Click here to openSchematic diagram:Click here to openat_instruction_set_CN_ONLY:Click here to open (If you mind about this, please don’t buy)hardware_info:Click here to openserial_tool:Click here to openFeature:Ca-01 development board characteristics and detailed parametersCommunication system:4GApplicable frequency band:LTE-FDD:B1/B3/B5/B8LTE-TDD:B34/B38/B39/B40/B41General characteristics:3GPP E-UTRA Release 13Band width:1.4/3/5/10/15/20MHZModule size:24.0mm x 24.0mm x 2.3mmPackage method:stamp hole + LGAModule weight:about 2.6gPower supply voltage:3.3V~4.3V, typical value …
4G Cat.1 LTE IoT Module Full Netcom Ca-01 4G Development BoardRead More
Reviews
There are no reviews yet.