10pcs Electronic DIY LED Dimming Lights Series and Parallel Circuit Technology Small Production Kit
$29.32
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Description
The purpose of the experiment
1. Understand and recognize the light-emitting diodes and illuminate the light-emitting diodes (LEDs);
2. Understand the role of understanding resistance, series and parallel resistance;
3. Understand the self-locking switch;
4. Understand and recognize adjustable resistors and use adjustable resistors;
Experimental steps
Step 1:The long leg of the light-emitting diode (LED) is the positive pole, and the short leg is the negative pole. First, the long wire of the LED is connected to the black wire (negative electrode) of the battery case, and the short leg of the LED is connected to the red wire (positive electrode) of the battery case. At this time, the light emitting diode (LED) is not lit. Then send it over again, let the long leg of the LED connect to the red line of the battery box, and the short leg of the LED is connected to the black line of the battery box. At this time, the LED lights up, indicating that the LED is in one-way operation and the single-pass characteristic of the diode .
Step 2:In the circuit of the experimental step 1, a resistor of 220 ohms is inserted in series, and the brightness of the LED lamp is lowered, and the resistance hinders the current.
Step 3:Connect a 220 ohm resistor in parallel with the resistance in the circuit of the experimental board 2. The brightness of the LED is increased, indicating that the total resistance of the resistor in the circuit is reduced after the resistors are connected in parallel.
Step 4:Change the two resistors of the experimental step 3 from parallel to series. After the series connection, the brightness of the LED lamp is the lowest. After the series connection of the resistors, the total resistance of the resistor in the circuit increases.
Step 5:Replace the original resistor with a potentiometer. The potentiometer has 3 feet, and the resistance of pins 1 and 3 is fixed. The resistance of pins 1 and 2, 2 feet and 3 feet can be changed by adjusting the potentiometer knob. When experimenting, you can pick up 2 of them. The foot has to experiment many times, adjust the potentiometer knob to observe the change of LED brightness, so that you can fully understand the potentiometer.
Step 6:Know the self-locking. Press and wait for the light to be on, then press the light to turn off.
Package included
10 x DIY LED Dimming Lights Technology Small Production Kit
Weight | 0.27 kg |
---|
Customers Also Viewed
5pcs Electronic DIY LED Dimming Lights Series and Parallel Circuit Technology Small Production Kit
$16.60DIY Electronic KitsAdd to cartDescriptionThe purpose of the experiment1. Understand and recognize the light-emitting diodes and illuminate the light-emitting diodes (LEDs);2. Understand the role of understanding resistance, series and parallel resistance;3. Understand the self-locking switch;4. Understand and recognize adjustable resistors and use adjustable resistors;Experimental stepsStep 1:The long leg of the light-emitting diode (LED) is the positive pole, and the …
50pcs Universal PCB Board 7x9cm 2.54mm Hole Pitch DIY Prototype Paper Printed Circuit Board Panel Single Sided Board
$32.93Electronic Accessories & SuppliesAdd to cartFeaturesPremium one side prototype PCB printed circuit board, universal strip breadboard.All holes are plated through, smooth and clear.Sturdy and easy to use, the plated holes are very solid which makes it very easy to solder components on and they can hold up well and handle reasonable heat levels and dwell times.A good assortment of quality …
50mm Submersible Bore 0.5 HP Water Farm Garden Deep Well Pump 220V 180ft 8GPM
$340.19Electrical Pump & ValveAdd to cartFeatures-2inch deep well submersible pump, fits in the 2inch well casing.-Patented impeller design provides extended pump life and heavy flow under the severe circumstances.-This pump has a much longer pump life than the all-plastic-bottom-suction pump.-Solid 304 stainless steel body with heavy duty cast iron discharge.-Industrial grade heavy duty, also good for home usage.-Built in 1/2 …
50mm Submersible Bore 0.5 HP Water Farm Garden Deep Well Pump 220V 180ft 8GPMRead More
1Hz-150Khz 3.3V-30V Signal Generator PWM Pulse Frequency Duty Cycle Adjustable Module LCD Display
$22.06Other Module BoardAdd to cartParameter settingsThe module has four independent keys, used to set the frequency and duty cycle, support short press (increase or decrease a unit)and long press (fast increase or decrease), very simple, set the parameters automatically save, power failure Lost.Module parameters1. Working voltage:3.3 ~ 30V;2. Frequency range:1Hz ~ 150KHz;3. Frequency accuracy:the accuracy in each range is …
5pcs LCD1602 LCD Shell for 1602 Blue/Yellow And I2C 1602 Blue/Yellow Green Backlight LCD Module Case
$17.73Electronic Accessories & SuppliesAdd to cartDescription Screen size:2.5 inches Material:acrylic Application 1602 Blue Backlight LCD Display Module:https://www.hobbyant.com/1Pc-1602-Character-LCD-Display-Module-Blue-Backlight-p-978160.htmlrmmds=search 1602 Yellow Backlight LCD Display Module:https://www.hobbyant.com/1Pc-1602-Character-LCD-Display-Module-Yellow-Backlight-For–p-978155.htmlrmmds=search I2C 1602 Blue Backlight LCD Display Module:https://www.hobbyant.com/IIC-I2C-1602-Blue-Backlight-LCD-Display-Module-For–p-950726.htmlrmmds=search I2C 1602 Yellow Green Backlight LCD Display Module:https://www.hobbyant.com/IICI2C-1602-Yellow-Green-Backlight-LCD-Display-Module-For–p-950728.htmlrmmds=search Package included 5 x LCD1602 LCD shell
Reviews
There are no reviews yet.