10pcs Electronic DIY LED Dimming Lights Series and Parallel Circuit Technology Small Production Kit
$29.32
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Description
The purpose of the experiment
1. Understand and recognize the light-emitting diodes and illuminate the light-emitting diodes (LEDs);
2. Understand the role of understanding resistance, series and parallel resistance;
3. Understand the self-locking switch;
4. Understand and recognize adjustable resistors and use adjustable resistors;
Experimental steps
Step 1:The long leg of the light-emitting diode (LED) is the positive pole, and the short leg is the negative pole. First, the long wire of the LED is connected to the black wire (negative electrode) of the battery case, and the short leg of the LED is connected to the red wire (positive electrode) of the battery case. At this time, the light emitting diode (LED) is not lit. Then send it over again, let the long leg of the LED connect to the red line of the battery box, and the short leg of the LED is connected to the black line of the battery box. At this time, the LED lights up, indicating that the LED is in one-way operation and the single-pass characteristic of the diode .
Step 2:In the circuit of the experimental step 1, a resistor of 220 ohms is inserted in series, and the brightness of the LED lamp is lowered, and the resistance hinders the current.
Step 3:Connect a 220 ohm resistor in parallel with the resistance in the circuit of the experimental board 2. The brightness of the LED is increased, indicating that the total resistance of the resistor in the circuit is reduced after the resistors are connected in parallel.
Step 4:Change the two resistors of the experimental step 3 from parallel to series. After the series connection, the brightness of the LED lamp is the lowest. After the series connection of the resistors, the total resistance of the resistor in the circuit increases.
Step 5:Replace the original resistor with a potentiometer. The potentiometer has 3 feet, and the resistance of pins 1 and 3 is fixed. The resistance of pins 1 and 2, 2 feet and 3 feet can be changed by adjusting the potentiometer knob. When experimenting, you can pick up 2 of them. The foot has to experiment many times, adjust the potentiometer knob to observe the change of LED brightness, so that you can fully understand the potentiometer.
Step 6:Know the self-locking. Press and wait for the light to be on, then press the light to turn off.
Package included
10 x DIY LED Dimming Lights Technology Small Production Kit
Weight | 0.27 kg |
---|
Customers Also Viewed
5PCS Cake Stand Set for Wedding Decorations White Table Kit Decorating Party Suppliers for Fondant Dessert Metal Cupcake Stand
$159.44Lab Clamp & StandAdd to cart5Pcs Metal Cupcake Stand Cake Dessert Wedding Event Party Display Tower Plate Features※ Ideal cake stand, widely used for personal birthday party, birthday, celebrations, banquets, marriage, graduation ceremony. ※ Used to display merchandise, play a very good decorative effect.※ This is also perfect for afternoon tea session. ※ High quality raw iron material, rejecting waste …
Robotdyn Digital Tilt Sensor Module Tilt Switch Angle
$8.73Sensor & Detector ModuleAdd to cartSize ConversionInchesCentimetersPlease according to your own measurements to choose your suitable size. The tags inside the items will show in our Asian (Type) size.FeatureDigital tilt sensor, have simple function, if the sensor are not placed on a strict flat surface, the little steel ball in the green tube will slip to one end of it, …
Robotdyn Digital Tilt Sensor Module Tilt Switch AngleRead More
20pcs LM317 DC-DC 1.5A 1.2-37V Adjustable Power Supply Board DC Converter Buck Step Down Module
$41.11Boost & Buck ModuleAdd to cartSpecificationsOutput Current:1.5A (minimum), 2.2A (typical value)Input-output voltage difference (VI-VO):40Vdc (max)Adjustable output voltage range:1.2 – 37VWorking temperature:-55 ° C to + 150 ° CCurrent output:1.5AVoltage Input:4.2 – 40 VOperating temperature:0 ° C – 125 ° CCharacteristic frequency:100 (MHz)Module size:35.6 (mm) x 16.8 (mm)Output mode:VOUT output positive, GND output negativePackage included20 x LM317 DC-DC 1.5A 1.2-37V adjustable …
4-way Switch Module Ewelink Phone Remote Control Small Voice DIY SCM Development Modified Board
$13.11Sensor & Detector ModuleAdd to cartSize ConversionInchesCentimetersPlease according to your own measurements to choose your suitable size. The tags inside the items will show in our Asian (Type) size.Power supply descriptionThis module uses 5V DC power supply, usable with USB power supply equipment such as mobile phone charger, charging treasure, computer and so on.Enter descriptionIt can be connected with four …
MPR121-Breakout-v12 Proximity Capacitive Touch Sensor Controller Keyboard Development Board
$8.73Sensor & Detector ModuleAdd to cartDescriptionThis is a breakout board for Freescale’s MPR121QR2. The MPR121 is a capacitive touch sensor controller driven by an I2C interface.The chip can control up to twelve individual electrodes, as well as a simulated thirteenth electrode. The MPR121 also features eight LED driving pins. When these pins are not configured as electrodes, they may be …
MPR121-Breakout-v12 Proximity Capacitive Touch Sensor Controller Keyboard Development BoardRead More
DG7512 75V 12A High Current Ideal Diode Solar Energy Anti-backflow Charging Anti-backflow Protection Low Resistance
$7.64Electronic Accessories & SuppliesAdd to cartSpecificationModule name:DG7512 anti-backflow ideal diodeWorking voltage:DC5-75VWorking current:12A (MAX) (without heat dissipation for a long time working within 10A,Can be used in parallel to increase operating current)Static operating current:0.7mAInput reverse connection protection:None (do not reverse the positive and negative poles, otherwise the chip will be burned)Working temperature:-40→~125→Connection method:welding outputModule size:25 *14*3.8mmPackage included1 x High Current Ideal …
HBV-1610 2MP Auto Focus Micro Mini USB2.0 Camera Module with Flash Light
$28.42Other Module BoardAdd to cartSpecificationsModel No.:HBV-1610Model Size:86.11mm ≠ 21mm ≠ 5.03mm÷0.2MMTemperature (Operation):-30C to 70CTemperature (Stable Image):0C to 50CAssembly technique:SMT (ROSH)Focus:AutoObject distance:30CM-infinityResolution:600LW/PH (Center)PCB printing ink:Blackinterface:USB 2.0Power supply:USB bus powersupply voltage:DC 5V÷5%Maximum Power consumption:730 mWOperating system request:Win XP/win 7,8 / vista /android 4.0/ mac /Linuxwith uvc Sensor:GT2005 (1/5” )Seneor Package:CSP,Bare DieMaximum resolution:1600*1200Sensitivity:33000mv /(lux-sec)Pixel Size:1.75m x 1.75┢m Maximum Image Transfer Rate:MJPEG 640×480 …
HBV-1610 2MP Auto Focus Micro Mini USB2.0 Camera Module with Flash LightRead More
Reviews
There are no reviews yet.