10pcs Electronic DIY LED Dimming Lights Series and Parallel Circuit Technology Small Production Kit
$29.32
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Description
The purpose of the experiment
1. Understand and recognize the light-emitting diodes and illuminate the light-emitting diodes (LEDs);
2. Understand the role of understanding resistance, series and parallel resistance;
3. Understand the self-locking switch;
4. Understand and recognize adjustable resistors and use adjustable resistors;
Experimental steps
Step 1:The long leg of the light-emitting diode (LED) is the positive pole, and the short leg is the negative pole. First, the long wire of the LED is connected to the black wire (negative electrode) of the battery case, and the short leg of the LED is connected to the red wire (positive electrode) of the battery case. At this time, the light emitting diode (LED) is not lit. Then send it over again, let the long leg of the LED connect to the red line of the battery box, and the short leg of the LED is connected to the black line of the battery box. At this time, the LED lights up, indicating that the LED is in one-way operation and the single-pass characteristic of the diode .
Step 2:In the circuit of the experimental step 1, a resistor of 220 ohms is inserted in series, and the brightness of the LED lamp is lowered, and the resistance hinders the current.
Step 3:Connect a 220 ohm resistor in parallel with the resistance in the circuit of the experimental board 2. The brightness of the LED is increased, indicating that the total resistance of the resistor in the circuit is reduced after the resistors are connected in parallel.
Step 4:Change the two resistors of the experimental step 3 from parallel to series. After the series connection, the brightness of the LED lamp is the lowest. After the series connection of the resistors, the total resistance of the resistor in the circuit increases.
Step 5:Replace the original resistor with a potentiometer. The potentiometer has 3 feet, and the resistance of pins 1 and 3 is fixed. The resistance of pins 1 and 2, 2 feet and 3 feet can be changed by adjusting the potentiometer knob. When experimenting, you can pick up 2 of them. The foot has to experiment many times, adjust the potentiometer knob to observe the change of LED brightness, so that you can fully understand the potentiometer.
Step 6:Know the self-locking. Press and wait for the light to be on, then press the light to turn off.
Package included
10 x DIY LED Dimming Lights Technology Small Production Kit
Weight | 0.27 kg |
---|
Customers Also Viewed
DC 2-12V to 12V 9V 9W USB Boost Power Supply Module Step Up Module DC Converter
$4.36Boost & Buck ModuleAdd to cartSpecificationsStarting voltage:2VInput voltage:2V-12V DCOutput voltage:12V DC (9V DC)Input current:2AOutput voltage:default 12V, 9V can be setOutput power:≤8w (in the case of input 5V, it is easy to overheat)No-load currentWorking temperature:-40 to -80 ° CBoard size:25*14*5mm (length * width * height does not include USB)The General Test Data (just for reference)Input DC2V boost to 12V output current …
DC 2-12V to 12V 9V 9W USB Boost Power Supply Module Step Up Module DC ConverterRead More
5Pcs DC24V Coil Power Relay LY2NJ JQX-13F DPDT 8 Pin PTF08A with Socket Base
$26.55Electronic Accessories & SuppliesAdd to cartSpecificationsModel:LY2NJ (8 pins)Coil voltage:DC24VCoil Power:DC (W):≤0.9AC (VA):≤1.2Contact Structure:8 pins 2 normally open 2 normally closedContact capacity:10A 250VACPull-in voltage:≤80% (V)Release voltage:DC:≥10% (V), AC:≥30%Contact resistance:≤50 (mΩ)Insulation resistance:≤100 (mΩ)Dimensions:27.5 * 21 * 35.3mmTerminals form:SocketAction time:20ms or lessReset Time:20ms or lessOperating frequencyMechanical 18,000 cycles / hourElectrical 18,000 times / hourPackage included5 x DC24V Coil Power Relay with socket base
40*160 0.5mm Blue Aluminum Alloy Water Cooling Block Radiator Liquid Cooler Heat Sink Equipment
$24.29Other Module BoardAdd to cartFeatures1. New high quality, Connector outer diameter 9.5mm, connector inner diameter 6-8mm.2. Inner flow channel extrusion.3. Welding from components to a whole one.4. Suitable for computer CPU water, industrial inverter drive, cooling, industrial switchboard cooling.5. Rate of less than 5X10-6 mbar.l/s parts.6. Internal fin thickness 0.5MM.SpecificationMaterial:luminum alloyColor:blueSize:pprox. 40x160x12mmProcessing:Vacuum auminum BrazingPackage includes1 x Water Cooling
20Pcs DS18B20 Temperature Sensor 18B20 TO-92 Encapsulation
$44.75Electronic Accessories & SuppliesAdd to cart20Pcs DS18B20 Temperature Sensor 18B20 TO-92 EncapsulationSpecificationTemperature measurement range:-55°C ~ +125°CAccuracy:± 0.5°CEncapsulation:TO-92Quantity:20pcsPackage included20 x DS18B20
20pcs WXD3-13-2W Precision Potentiometer 22K 22K Ohm Wirewound Multi-Turn Potentiometer
$49.11Module ComponentsAdd to cartSpecificationsResistance range:22K┯Resistance tolerance:÷ 5%Rotation angle:3600 ÷ 20 Number of laps:10 lapsRated voltage:160VStarting torque:3.5 ~ 100mN.mRated power:2W (85 →) 0W (125 →)Linearity accuracy:÷ 0.3%Mechanical durability:10,000 weeksPackage included20 x Potentiometer
Reviews
There are no reviews yet.