Assembled 16 Level Sound Control Level indicator Blue LED Mono VU Meter Audio Music Spectrum Board AGC for MP3 Speaker Amplifiers DIY
$72.16
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Description
Microphone signal acquisition, added noise cancellation function + automatic gain control. Practical effect is better.
Tips
1. The power supply voltage must be 5V. Do not exceed 5V. Otherwise, the lamp board will be damaged.
2. Power supplies with currents greater than 150MA (0.15A) can be used, no matter how large. All right,
3. Some power supplies have fast charge high voltage output function, please do not use this type of charger.
4. The product does not have a power supply, no power cord.
How to use
Sound Control Level indicator operating instructions
Featrues
By micophone pickup (Sound Control)
Aluminum alloy integrated molding housing 181×16 x 18.5 mm.
Mono 16 segment square lights to ensure adequate dynamic range and shock enough.
Exclusive custom square rounded lights strip. (There are no similar lights in the market).
The rising speed and the falling speed of the light bar, the holding time and the falling speed of the peak can be adjusted separately.
The brightness of the lamp can be adjusted freely. Microphone sensitivity can be adjusted 15 levels.
The reaction speed of AGC can be adjusted 15 levels.
super wide range of AGC adaptive algorithm to ensure the best effect.. Single button operation.
Exclusive Software – the function of eliminating ambient noise . Specific operation:(There are LED instructions operating time)
Normal mode
1. 1 second – Mode switch (there will be a corresponding preview).
2. 5 seconds – Enter the speed setting mode.
3. 10 seconds – Factory default
4. Double Click – The function of eliminating ambient noise is turned off.
5.Three Click – The function of eliminating ambient noise is turned on.
After keeping quiet, the recognition was completed in a few seconds.
6. Four Click – Enter sensitivity setting mode(15 optional)
7. Five Click – Enter the AGC speed setting mode(15 optional)
8. Six Click – Adjust the brightness of the light bar,low/medium/high
Speed setting mode:(In normal mode, press the button for 5 seconds to enter, press the button for 5 seconds to exit) .
1. 1 second
a. The rising speed of the light bar (15 optional)
b. The falling speed of the light bar (15 optional)
c. The holding time of the peak (15 optional)
d. The falling speed of the peak (15 optional)
e. Brightness adjustment (15 optional)
Loop in these functions.
2. Click the button – Loop to change the parameters set.
I. Environmental noise can be eliminated:(In normal mode ,three-click button opens and automatically exits after recognition)
(Special description:Evey environment has different environmental noise,Because it’s the microphone that picks up the sound,and the microphone can’t recognize noise or music,So we need to eliminate environmental noise. Then the sound reflected by the level lamp is the real sound of music. Before making this correction,make sure you don’t play music or talk ,the whole process will be completed in 5 seconds,so that the current environmental noise can be recognized.It is suggested that correction should be made once for every change of environment.)
Sensitivity setting mode:(In normal mode, Four Click to enter,No click 5 seconds to exit.)
1. Single -Click – Sensitivity is reduced(The more lights light on the indicator ,The sensitivity will getting more lower (15 optional)).
2. Double-Click – Sensitivity increases(The less lights light on the indicator , The sensitivity will getting more higher (15 optional)).
NOTE
In order to achieve the best effect,it is suggested to lower the sensitivity when the signal amplitude is large,and in the case of small signal,the sensitivity can be increased.
AGC Speed Mode:(In normal mode, Five Click to enter,No click 5 seconds to exit.)
1. Single -Click – AGC speed reduced (The more lights light on the indicator,
The AGC speed will getting more slower(15 optional)).
2. Double-Click – AGC speed increases(The less lights light on the indicator,
The AGC speed will getting more faster (15 optional)).
NOTE
The principle of AGC is to enlarge the input small signal to full screen display, reduce the large signal to the range that the screen can display, and automatically scale the signal according to the size of the input signal.
The speed of the AGC is the speed at which the small signal is amplified to the full screen display. Because the input signal exceeds the display area, it will be compressed immediately. If it is used in an environment where the signal amplitude varies greatly, it is recommended that the AGC speed be adjusted to faster.)
Package included
1 x assembled 16 Level Sound Control Level Indicator
Weight | 0.119 kg |
---|
Customers Also Viewed
1.8 inch LCD TFT Display Module with PCB Backplane 128X160 SPI Serial Port
$15.30Display ScreenAdd to cartFeatureResolution:128X160Driver IC:ILI9163/ST7735Module with regulator IC supports 3.2V/5V power supplyWith SD card holder, you can do experiments like digital photo frameThe module reserves the Nokia3310/5110 interface, supports the 1602 interface, and directly plugs in and out.IO for streamlined wiring:(only 3 IOs after optimization)1. RST– directly connected to the microcontroller reset signal terminal, this IO can save2. …
1.8 inch LCD TFT Display Module with PCB Backplane 128X160 SPI Serial PortRead More
USB Boost 5V to 1.2V 3.3V 6V 9V 12V 24V Power Supply Module Adjustable Voltage
$10.92Test & Measuring ModuleAdd to cartFeatureInput voltage:3.5V-12VOutput voltage:1.2-24VOutput PowerOutput voltage 1.2V-2V, used within 2WOutput voltage 2V-20V, used within 3WOutput voltage 20V-24V, used within 2.5WOutput power = output voltage x output currentNote:This product is not a high power supply, please use it within the power range.Package includes1 x Power Module
10pcs IR LED infrared Light Board for CCTV Camera Night Vision 30-40M 6*Array LED White 2.5W DC12V
$26.76LED BoardAdd to cartSize ConversionInchesCentimetersPlease according to your own measurements to choose your suitable size. The tags inside the items will show in our Asian (Type) size.Features– High power / Spot Light / Infrared IR LED boards for CCTV cameras night vision.– Driven board & CDS sensor included.– Power supply exceeds DC13V may greatly reduce the LEDs operating …
2500Pcs 2.54mm XH2.54 2p 3p 4 Pin Connector Plug+Straight Needle+Terminal Socket Header Wire Adaptor
$56.09Electronic Accessories & SuppliesAdd to cartDescription2pin = 200 sets3pin = 200 sets4pin = 100 setsPin Connector Terminal:1500 pcs (Please allow 5% deviation)Package included10 x Connector plug kit with box
19PCS DIY Resin Casting Molds Silicone Jewelry Pendant Craft Making Mould Tool
$58.71ConnectorsAdd to cartSpecificationName:Resin Casting MoldsMaterial:SiliconeColor:TransparentFeature-Flexible, resistant to tearing.-Easy to use and clean.-Easy to release.-Durable in use.-Great for jewelry pendant making, earrings, soap making, chocolate making, sugarpaste making.-You can also add some flowers, glitter, colors to make your own art craft gift.Package Included9x Resin Casting Molds (Mold only, NO accessories)10x Wood Sticks
4G Cat.1 LTE IoT Module Full Netcom Ca-01 4G Development Board
$98.40Motherboard & Development BoardAdd to cartDocumentsProduct specification:Click here to openSchematic diagram:Click here to openat_instruction_set_CN_ONLY:Click here to open (If you mind about this, please don’t buy)hardware_info:Click here to openserial_tool:Click here to openFeature:Ca-01 development board characteristics and detailed parametersCommunication system:4GApplicable frequency band:LTE-FDD:B1/B3/B5/B8LTE-TDD:B34/B38/B39/B40/B41General characteristics:3GPP E-UTRA Release 13Band width:1.4/3/5/10/15/20MHZModule size:24.0mm x 24.0mm x 2.3mmPackage method:stamp hole + LGAModule weight:about 2.6gPower supply voltage:3.3V~4.3V, typical value …
4G Cat.1 LTE IoT Module Full Netcom Ca-01 4G Development BoardRead More
Reviews
There are no reviews yet.