DIY Airband Radio Receiver Aviation Band Receiver Kit
$43.73
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Description
Like many scanner enthusiasts and ham operators, you are interested in listening in on all the excitement manifest in aeronautic communication, but lack the equipment to pursue your interest, then maybe the Aviation-Band Receiver described in this article is for you.
The Aviation Receiver, designed to tune the 118-135MHz band, features exceptional sensitivity, image rejection, signal-to-noise ratio, and stability.
The receiver is ideally suited to listening in on ground and air communication associated with commercial airlines and general aviation.
Powered from a 9-volt alkaline battery, it can be taken along with your to local airports so that you won’t miss a moment of the action.
And even if you’re nowhere near an airport, this little receiver will pick-up all the ground-to-air and vice-versa communications of any plane or ground facility within about 130 miles (190Km).
Color:Green
Material:CCL
Construction
Once you have obtained all of the components and the board for the Aviation Receiver, construction can begin. A parts-placement diagram is shown in Fig. When assembling the project, take special care that polarity-sensitive components (electrolytic capacitors [keep leads as short as possible], diodes, and transistors) are installed properly. Just one part installed backwards can cause grievous harm!
Inductors (Aircoils) L1,L3,L5 can be made easily on a 5mm drill bit. Before you wind them, scrape the enamel of each end, about 5mm. Then wind the 1.5 turn (2-turns is okay too). I know it can be tricky especially if you have big fingers like me. Begin by installing the passive components (6 jumper wires, sockets, resistors, capacitors, inductors). Followed by installing the active components; diodes, transistors, and IC’s. Once the active components have been installed, check your work for the usual construction errors; cold solder joints, misplaced or reversed-lead components, solder bridges, etc. Once you have determined that he circuit has been correctly assembled, it’s time to consider the enclosure that will house the receiver.
The receiver’s circuit board can be housed in any enclosure that you choose.
Note
Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1-3cm.
Package included
1 x DIY KITs Airband Radio Receiver Aviation Band Receiver
1 x English manual
Weight | 0.081 kg |
---|
Customers Also Viewed
CC2530F256RHAR cc2530 Module Serial Port Transparent Transmission with ZB502 Development Board Kit
$52.47Module KitsAdd to cartNoteAt least two CC2530 modules are needed to realize Z1gBee networking, this product contains only one.Two methods can be usedApplication method:(The bottom layer is implemented by the board, you only do the application)Use the firmware associated with the board. In this way, the board is a Z1gBee wireless serial port module, the operation is as …
H2519-5 Dual Row Plastic Terminal 600V 36A 6 Positions Screw Terminal Block Cable Connector Barrier Terminal Strip Block
$12.14ConnectorsAdd to cartSpecificationModel:H2519-5Type:Terminal block Working frequency:High frequencyInterface type:AC/DCRated current:36ARated voltage:600VConductor cross section:0.5-6mm2Number of pin:6Number of bits:6Contact material:CopperInsulation material:Insulation plasticSize:55.6mm x 21mm x21mmFeature:1) High precision2) Excellent inoxidability3) High corrosion resistance4) Great ingredient accuracy and high intensity5) Widely used in lamp, decorated lighting, factory, household appliances, distribution boxes and other transmission equipment, specially point at wire, cable access and …
2 Lamp Backlight Universal LCD CCFL 10V-28V inverter
$8.73Other Module BoardAdd to cart2 Lamp Backlight Universal LCD CCFL 10V-28V Inverter For 10 Inch To 22 Inch ScreenFeatureVoltage:10V ~ 28VCable:300mm(L) / 6 pinSize:122 x 27mm ( L x W )Interface:double light small interfaceInterface definition:1. VCC 2. GND 3. NULL 4. NULL 5. ON/OFFPackage included1 x 2 lamp backlight universal laptop LCD CCFL inverter 10V-28V1 x Cable
Wanptek NPS306W 110V/220V 0-30V 0-6A Adjustable Digital DC Power Supply 180W Regulated Laboratory Switching Power Supply
$170.09Electrical DC Power SupplyAdd to cartProduct descriptionThe Wanptek NPS-W series is a three-window display mini DC power supply that simultaneously displays voltage, current, and power.This product improves the shortcomings of traditional linear power supplies that are bulky, heavy, and inefficient.The output voltage and current of the product can be controlled and adjusted by coarse adjustment and fine adjustment potentiometer respectively, …
5pcs CJMCU-5102 PCM5102A Stereo Digital To Analog Converter DAC PLL Voice Module
$50.58Sensor & Detector ModuleAdd to cartSize ConversionInchesCentimetersPlease according to your own measurements to choose your suitable size. The tags inside the items will show in our Asian (Type) size.DescriptionBrand:CJMCUPCM5102A Stereo DAC Digital To Analog Converter PLL Voice ModuleMore infos:!Package included5 x CJMCU-5102 Stereo DAC Digital To Analog Converter PLL Voice Module
1Channel RS485 MODBUS RTU Serial Port Multi-function Relay Module PLC Controller for Smart Home 12V DC
$12.66Relay ModuleAdd to cart>>> Manual:Click here to open SpecificationsWorking voltage:DC 12VWorking current:standby 11-13mA, 1 relay is on 44mA.Size:45 x 30 x 18 mmWeight:18 gramsMaximum load:10A / 250VAC, 10A / 125VAC, 10A / 30VDC, 10A / 28VDC, 10A / 12VDCFeatures-Six working modes:open, close, jog, self-lock, interlock, delay-AT command mode and MODBUS command control mode-Maximum delay of 9999 seconds under …
Reviews
There are no reviews yet.