DIY Airband Radio Receiver Aviation Band Receiver Kit
$43.73
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Description
Like many scanner enthusiasts and ham operators, you are interested in listening in on all the excitement manifest in aeronautic communication, but lack the equipment to pursue your interest, then maybe the Aviation-Band Receiver described in this article is for you.
The Aviation Receiver, designed to tune the 118-135MHz band, features exceptional sensitivity, image rejection, signal-to-noise ratio, and stability.
The receiver is ideally suited to listening in on ground and air communication associated with commercial airlines and general aviation.
Powered from a 9-volt alkaline battery, it can be taken along with your to local airports so that you won’t miss a moment of the action.
And even if you’re nowhere near an airport, this little receiver will pick-up all the ground-to-air and vice-versa communications of any plane or ground facility within about 130 miles (190Km).
Color:Green
Material:CCL
Construction
Once you have obtained all of the components and the board for the Aviation Receiver, construction can begin. A parts-placement diagram is shown in Fig. When assembling the project, take special care that polarity-sensitive components (electrolytic capacitors [keep leads as short as possible], diodes, and transistors) are installed properly. Just one part installed backwards can cause grievous harm!
Inductors (Aircoils) L1,L3,L5 can be made easily on a 5mm drill bit. Before you wind them, scrape the enamel of each end, about 5mm. Then wind the 1.5 turn (2-turns is okay too). I know it can be tricky especially if you have big fingers like me. Begin by installing the passive components (6 jumper wires, sockets, resistors, capacitors, inductors). Followed by installing the active components; diodes, transistors, and IC’s. Once the active components have been installed, check your work for the usual construction errors; cold solder joints, misplaced or reversed-lead components, solder bridges, etc. Once you have determined that he circuit has been correctly assembled, it’s time to consider the enclosure that will house the receiver.
The receiver’s circuit board can be housed in any enclosure that you choose.
Note
Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1-3cm.
Package included
1 x DIY KITs Airband Radio Receiver Aviation Band Receiver
1 x English manual
Weight | 0.081 kg |
---|
Customers Also Viewed
Solar Powered Floating Bird Bath Water Fountain Pump Pond Pool Water Pump
$42.51Electrical Pump & ValveAdd to cartDescriptionThis product is solar-powered decorative fountain.It is made up of highly efficient solar panel and new brushless pump.IT is start-up fast,efficient and strong stability.In addition,it has no electric outlet or external battery,so it’s not only easy to use,but also safe.This product is suitable for bird bath,fish tank,small pond,garden decoration,water circulation for oxygen,etc.FeatureSolar panel:7V/1.4WBrushless pump input:DC4.5-10VMaximum …
Solar Powered Floating Bird Bath Water Fountain Pump Pond Pool Water PumpRead More
Vibration Switch Sensor Module Vibration Sensor Alarm Module Smart Car Accessories
$4.36Sensor & Detector ModuleAdd to cartFeatures 1. Onboard LM393 voltage comparator chip and vibration sensing probe2. Support 5V/3.3V voltage input3. Onboard signal output indication, the output valid signal is low level and the indicator light is on, the output signal can be directly connected with the single chip IO4. The sensitivity of signal detection can be adjusted5. With 3mm screw …
Vibration Switch Sensor Module Vibration Sensor Alarm Module Smart Car AccessoriesRead More
TPA3116 Dual Channel 50Wx2 Digital Amplifier Board
$23.15Amplifier BoardAdd to cartSpecificationPower amplifier chip:TPA3116Power supply voltage:11 ~ 26VDC DC input with limit reverse polarity protection(Recommended DC 24V current 3A and above switching power supply)Output power:stereo 50W + 50W, PBTL monaural 100WLoad impedance:4 to 8 ohms (horn speaker impedance)Audio input:2.54mm3 pin seatPackage Included1 x Digital Amplifier Board
5pcs Geekcreit 3 in 1 AC 60-500V 100A Square Yellow LED Digital Voltmeter Ammeter Hertz Meter Signal Lights Voltage Current Frequency Combo Meter indicator Tester with Round CT
$48.24Electronic Accessories & SuppliesAdd to cartDescriptionDisplay:Voltage, current, frequencyDisplay color:YellowMeasuring voltage range:60~500V AMeasuring current range:6~100AMeasuring frequency range:20-70HzSize:2.8*5cm/1.10inch*1.97inch (D*H)Note:Due to the difference between different monitors, the picture may not reflect the actual color of the item. Thank you!!Package included5 x 22MM Indicator5 x Round CT
5pcs Nano V3.0 Terminal Adapter AVR ATMEGA328P without NRF2401+ Expansion interface DC Power Board
$38.18Expansion Board & ShieldAdd to cartFeature1. The item is a terminal expansion adapter, working very well for prototyping Nano projects2. There are pins expansion hole for the NANO board, which can directly lead the pins; With DC power supply interface, you can directly add external power or battery to supply power3. With NRF2401+ expansion interface, you can insert NRF2401+ to …
Reviews
There are no reviews yet.