US-100 Ultrasonic Ranging Module with Temperature Compensated Sensor Dual Mode Serial Port
$10.92
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Characteristic
The US-100 ultrasonic ranging module can provide 2cm-450cm non-contact distance sensing function, wide working voltage, self-contained temperature sensor to correct the ranging result, and also has GPIO, serial port and other communication methods. The dog is stable and reliable.
The module includes a transmitter, receiver and control circuit, which is a piezoelectric sensor that is fabricated using electrostrictive phenomena.
An alternating voltage is applied to the piezoelectric material slice (such as quartz crystal, piezoelectric ceramic, lead bismuth titanate, etc.) to cause it to generate electrostrictive vibration to generate ultrasonic waves. The resonance is generated when the frequency of the applied alternating voltage is equal to the natural frequency of the wafer, and the ultrasonic wave generated at this time is the strongest.
Piezoelectric ultrasonic receivers generally operate using the inverse effect of an ultrasonic generator. The structure is basically the same as that of an ultrasonic generator, and sometimes the same transducer is used as both a generator and a receiver.
When the ultrasonic wave acts on the piezoelectric wafer, the wafer is stretched and contracted, and alternating charges are generated at the two interfaces of the wafer, and then converted into a voltage and amplified to be sent to the measuring circuit, and finally recorded or displayed.
Electrical parameters:US-100 ultrasonic ranging module
Operating Voltage:DC 2.4V~5.5V
Quiescent Current:2mA
Operating temperature:-20~+70 degrees
output method:Level or UART (jumper cap selection)
Induction angle:Less than 15 degrees
Detection distance:2cm-450cm
Detection accuracy:0.3cm+1%
Serial port configuration in UART mode:The baud rate is 9600, the start bit is 1 bit, the stop bit is 1 bit, the data bit is 8 bits, there is no parity, no flow control.
Pin 1:Connect to VCC power supply (DC 2.4V-5.5V).
Pin 2:When it is in UART mode, it is connected to the TX terminal of the external circuit UART; when it is in the level trigger mode, it is connected to the Trig terminal of the external circuit.
Pin 3:When in UART mode, connect to RX terminal of external circuit UART; when it is level trigger mode, connect to Echo terminal of external circuit.
Pin 4/5:Connect the ground of the external circuit, and the two pins are turned on.
Level-triggered ranging works
Before powering up the module, first remove the jumper cap on the mode selection jumper to put the module in level trigger mode.
It can be seen from the figure that only a high level of 10US or more is required to be input to the Trig/TX pin, and the system can send eight 40KHZ ultrasonic pulses and then detect the echo signal. When the echo signal is detected, the module also measures the temperature value, then corrects the ranging result according to the current temperature, and outputs the corrected result through the Echo/RX pin. In this mode, the module converts the distance value to twice the time value at 340m/s, outputs a high level through the Echo terminal, and simultaneously starts the timer, and can read the timer when the port goes low. The value of the high level is the time from the transmission to the return of the ultrasonic wave. The distance value can be calculated based on the duration of this high level. That is, the distance value is:(high time *340m/s)/2.
Note:Since the distance value has been temperature corrected, it is no longer necessary to correct the ultrasonic sound speed according to the ambient temperature, that is, the sound speed is 340m/s regardless of the temperature.
Serial port triggering ranging works
Before the module is powered on, first plug in the jumper cap on the mode selection jumper to make the module in serial port trigger mode.
In this mode, only need to input 0X55 (baud rate 9600) on the Trig/TX pin, the system can send 8 40KHZ ultrasonic pulses and then detect the echo signal. When the echo signal is detected, the module also measures the temperature value, then corrects the ranging result according to the current temperature, and outputs the corrected result through the Echo/RX pin. The output distance value is a total of two bytes, the first byte is the upper 8 bits of the distance (HDate), and the second byte is the lower 8 bits of the distance (LData), in millimeters. That is, the distance value is (HData*256 + LData) mm.
Serial port trigger temperature measurement working principle
Before the module is powered on, first plug in the jumper cap on the mode selection jumper to make the module in serial port trigger mode.
In this mode, only need to input 0X50 (baud rate 9600) on the Trig/TX pin, the system will start the temperature sensor to measure the current temperature, and then output the temperature value through the Echo/RX pin. After measuring the completion temperature, the module will return a byte temperature value (TData), the actual temperature value is TData-45. For example, after sending 0X50 through TX and receiving 0X45 on RX, the temperature value at this time is [69 (0X45 decimal value) -45] = 24 degrees.
Precautions
1. This module should not be connected with power. If you want to have a live connection, first connect the GND terminal of the module first, otherwise it will affect the normal operation of the module.
2. When measuring distance, the area of the measured object is not less than 0.5 square meters and the plane should be flat as much as possible, otherwise the measurement result will be affected.
3. If the test surface is not very regular or when testing a distant object, multiple measurements can be used to correct it.
Package includes
1 x US-100 Ultrasonic Ranging Module
Weight | 0.009 kg |
---|
Customers Also Viewed
10Pcs Mesh Pot Net Basket Hydroponic Aeroponic Flower Container Plant Grow Pot Cup Planting Baskets
$16.19Lab Clamp & StandAdd to cartSpecification Material:Plastic Height:100mm Weigh:10gThe upper edge of the outer diamete:70mmThe outer diameter:63mmThe lower end of the outer diameter:54mmFeatures1.Good permeability:these net cups are designed with slotted mesh, can promote a more efficient plant growth through aeration.2.Growing by its own way:net pot with holes in the bottom, produce healthy roots with even drainage, which let the roots …
2Pcs Yellow Color Cute Pattern Silicone Protective Case for Micro:bit Expansion Board DIY Part
$19.02Smart Robot & Solar PanelAdd to cartFeatures1. Appearance and fun, make accessories safer2. Food Grade Safety Silicone Materials3. Protect Microbit from external wearSpecifications– Product Size:56*45mm– Thickness:12mm– Color:Yellow– Material:silica gel– Fit for:Micro:bit Expansion Board– Quantity:2Package Inlcuded2 x Yellow Micro:bit Silicone Protective Case (Not included the Micro:bit control board)
Hepa Filter Accessory for ELECTROLUX H13 Vacuum Cleaner
$22.26Switch AccessoriesAdd to cartHEPA H13 Filter for Most Modern ELECTROLUX Vacuum CleanerSpecificationsMaterial:PlasticFit For:Electrolux,Boldio,Excellio,Oxygen,Oxy3-Systems,Praxio,Powersystem,Smartvac,Ultra Silencer Series,FC8031 SeriesPackage Included1 x Filter
Wood Heating Stove Door Gasket Round Fiberglass Rope Seal High Density Fibreglass Strips Rope
$22.67FabricsFibers & TextilesAdd to cart2m 9.5mm High Density Fibreglass Rope Wood Fire Stove & Heater Door Seal 550°CSpecificationType:Fibreglass RopeColor:WhiteMaterial:FibreglassFire-resistant temperature:550 (°C)Tear strength:300Compressive strength:100Tensile strength:300Elongation at break:100Size:approx.9.5mm*2m(1cm=10mm=0.39inch)Measurement Details in the attached picture.Package Included1X Fibreglass RopeFeatureIt is tough, durable and strong yet flexible enough to make installation as a door seal easy.Our Fibreglass Rope has a maximum operating temperature of 550°C. …
100Pcs PCB DIY Soldering Copper Prototype Printed Circuit Board 70mm x 90mm
$104.88Electronic Accessories & SuppliesAdd to cartSpecificationMaterial:Single Side Copper PCB (Made of bakelite)Quantity:5PcsSize:70 x 90mm / 2.75 x 3.54inch(Approx. L*W)Thickness:1.5mm / 0.59inch(Approx)Hole pitch:2.54mm / 0.1inch(Approx)Diameter of Hole:1mm / 0.04inch(Approx)For DIY solderingEasy to installGreat for electronic accessoriesPackage includes100 x Circuit Board
10pcs KSD9700 250V 5A 45 Plastic thermostatic Temperature Sensor Switch NC
$9.96Sensor & Detector ModuleAdd to cartFeaturesKSD9700 product widely used in home appliance’s motor and electrical equipment, such as air conditioner motor, transformer, thermal appliances, etc.SpecificationModel.No.:KSD9700Material:PlasticNet Weight:3gOptional:Normally Closed (NC)Rated Voltage:250VCurrent:5ACable Length (Approx.):7.3cm/ 2.9 inchHead Dimension (Approx.):21 x 7.5 x 3.6mm / 0.8 x 0.3 x 0.14 inch (L*W*T)Temperature:45→Package included10 x Temperature Control Switch
Electronics Component Super Kit with Jumper wires Color Led Resistors Register Card Buzzer for Arduino
$43.00DIY Electronic KitsAdd to cartFeatureElectronics component super kit perfect for anybody who use for Arduino, raspberry piPackage included1 x Project Box1 x Power Supply Module1 x 830 Holes Breadboard10 x Resistor(100┯)10 x Resistor(220┯)10 x Resistor(330┯)10 x Resistor(560┯)10 x Resistor(1k)10 x Resistor(2k)10 x Resistor(4.7k)10 x Resistor(10k)10 x Resistor(20k)10 x Resistor(51k)10 x Resistor(1M)10 x Resistor(10M)5 x 100uf Electrolytic Capacitors5 x 100nf …
Keyes NEO-7M GPS Module Satellite Positioning onboard Ceramic Antenna Serial Port Driver
$34.98Smart ModuleAdd to cartOverviewThis GPS module is based on the NEO-7M, can be used for satellite positioning. The module supports NMEA standard protocol output, built-in FLASH, and can save the setting information after power-off without external EEPROM. This module has an on-board ceramic antenna, which can easily locate the satellite in an open place without an external antenna. …
Keyes NEO-7M GPS Module Satellite Positioning onboard Ceramic Antenna Serial Port DriverRead More
Reviews
There are no reviews yet.