US-100 Ultrasonic Ranging Module with Temperature Compensated Sensor Dual Mode Serial Port
$10.92
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Characteristic
The US-100 ultrasonic ranging module can provide 2cm-450cm non-contact distance sensing function, wide working voltage, self-contained temperature sensor to correct the ranging result, and also has GPIO, serial port and other communication methods. The dog is stable and reliable.
The module includes a transmitter, receiver and control circuit, which is a piezoelectric sensor that is fabricated using electrostrictive phenomena.
An alternating voltage is applied to the piezoelectric material slice (such as quartz crystal, piezoelectric ceramic, lead bismuth titanate, etc.) to cause it to generate electrostrictive vibration to generate ultrasonic waves. The resonance is generated when the frequency of the applied alternating voltage is equal to the natural frequency of the wafer, and the ultrasonic wave generated at this time is the strongest.
Piezoelectric ultrasonic receivers generally operate using the inverse effect of an ultrasonic generator. The structure is basically the same as that of an ultrasonic generator, and sometimes the same transducer is used as both a generator and a receiver.
When the ultrasonic wave acts on the piezoelectric wafer, the wafer is stretched and contracted, and alternating charges are generated at the two interfaces of the wafer, and then converted into a voltage and amplified to be sent to the measuring circuit, and finally recorded or displayed.
Electrical parameters:US-100 ultrasonic ranging module
Operating Voltage:DC 2.4V~5.5V
Quiescent Current:2mA
Operating temperature:-20~+70 degrees
output method:Level or UART (jumper cap selection)
Induction angle:Less than 15 degrees
Detection distance:2cm-450cm
Detection accuracy:0.3cm+1%
Serial port configuration in UART mode:The baud rate is 9600, the start bit is 1 bit, the stop bit is 1 bit, the data bit is 8 bits, there is no parity, no flow control.
Pin 1:Connect to VCC power supply (DC 2.4V-5.5V).
Pin 2:When it is in UART mode, it is connected to the TX terminal of the external circuit UART; when it is in the level trigger mode, it is connected to the Trig terminal of the external circuit.
Pin 3:When in UART mode, connect to RX terminal of external circuit UART; when it is level trigger mode, connect to Echo terminal of external circuit.
Pin 4/5:Connect the ground of the external circuit, and the two pins are turned on.
Level-triggered ranging works
Before powering up the module, first remove the jumper cap on the mode selection jumper to put the module in level trigger mode.
It can be seen from the figure that only a high level of 10US or more is required to be input to the Trig/TX pin, and the system can send eight 40KHZ ultrasonic pulses and then detect the echo signal. When the echo signal is detected, the module also measures the temperature value, then corrects the ranging result according to the current temperature, and outputs the corrected result through the Echo/RX pin. In this mode, the module converts the distance value to twice the time value at 340m/s, outputs a high level through the Echo terminal, and simultaneously starts the timer, and can read the timer when the port goes low. The value of the high level is the time from the transmission to the return of the ultrasonic wave. The distance value can be calculated based on the duration of this high level. That is, the distance value is:(high time *340m/s)/2.
Note:Since the distance value has been temperature corrected, it is no longer necessary to correct the ultrasonic sound speed according to the ambient temperature, that is, the sound speed is 340m/s regardless of the temperature.
Serial port triggering ranging works
Before the module is powered on, first plug in the jumper cap on the mode selection jumper to make the module in serial port trigger mode.
In this mode, only need to input 0X55 (baud rate 9600) on the Trig/TX pin, the system can send 8 40KHZ ultrasonic pulses and then detect the echo signal. When the echo signal is detected, the module also measures the temperature value, then corrects the ranging result according to the current temperature, and outputs the corrected result through the Echo/RX pin. The output distance value is a total of two bytes, the first byte is the upper 8 bits of the distance (HDate), and the second byte is the lower 8 bits of the distance (LData), in millimeters. That is, the distance value is (HData*256 + LData) mm.
Serial port trigger temperature measurement working principle
Before the module is powered on, first plug in the jumper cap on the mode selection jumper to make the module in serial port trigger mode.
In this mode, only need to input 0X50 (baud rate 9600) on the Trig/TX pin, the system will start the temperature sensor to measure the current temperature, and then output the temperature value through the Echo/RX pin. After measuring the completion temperature, the module will return a byte temperature value (TData), the actual temperature value is TData-45. For example, after sending 0X50 through TX and receiving 0X45 on RX, the temperature value at this time is [69 (0X45 decimal value) -45] = 24 degrees.
Precautions
1. This module should not be connected with power. If you want to have a live connection, first connect the GND terminal of the module first, otherwise it will affect the normal operation of the module.
2. When measuring distance, the area of the measured object is not less than 0.5 square meters and the plane should be flat as much as possible, otherwise the measurement result will be affected.
3. If the test surface is not very regular or when testing a distant object, multiple measurements can be used to correct it.
Package includes
1 x US-100 Ultrasonic Ranging Module
Weight | 0.009 kg |
---|
Customers Also Viewed
K202 Low Power Consumption Fingerprint Control Board Switch Fingerprint Access Control Board DC12V
$17.48Other Module BoardAdd to cart>>>Manual:Click here to openSpecifications·P1:Power supply:DC12V·Output:Relay(Max. current:10A)·Standby current:15uA·Fingerprint capacity:120 pieces·Size:64.4*25.4mm·P2:MX 1.0mm space 6 Pin Fingerprint Module(can connect R502,R502-A,R502-AW,R503)·P3:MX 1.25mm space 6 Pin Fingerprint Module(can connect R300,R301T,R303,R303T,R305,R306,R307,R501)K202 is designed for low power consumption, the power supply is DC12V, the relay time can be adjusted by rotating the button, relay time:0.5-13 seconds.It is very easy to register fingerprint, …
intelligent Voice Recognition Module AC108 Audio Decoding Module 4 Microphones Decoder for Smart Speaker DIY
$28.42Expansion Board & ShieldAdd to cartSize ConversionInchesCentimetersPlease according to your own measurements to choose your suitable size. The tags inside the items will show in our Asian (Type) size.Feature1. Based on RASPBERRY PI 40PIN interface, suitable for RASPBERRY PI series motherboards;2. Support RASPBERRY PI ZERO / ZERO W / 2B / 3B / 3B + / 4 and other development …
GP2Y1010AU0F Dust Sensor Module Dust Particle Concentration PM2.5 Haze Detection
$32.79Sensor & Detector ModuleAdd to cartFeaturesEasy to use:only one AD acquisition pin and one control pin are neededAnalog output:The output voltage is linearly related to the dust concentration in the effective range, with a built-in attenuation circuit, the output voltage does not exceed 1.5VSensitivity:0.5V/(100┢g/m3)Effective range:500┢g/m3Wide power supply range:built-in booster circuit, working voltage range 2.5V to 5.5VLow power consumption:within a sampling …
GP2Y1010AU0F Dust Sensor Module Dust Particle Concentration PM2.5 Haze DetectionRead More
3pcs TM1637 4 Bits Digital LED Display Module 7 Segment 0.36 inch RED Anode Tube 4 Serial Driver Board for
$11.00Display ScreenAdd to cartIntroductionThe module is a 12-pin display module with a 4-point common digital tube (0.36 inch) with a clock point. The driver chip is TM1637. It only needs 2 signal lines to enable the MCU to control the 4-bit 8- Segment digital tube.FeaturesDigital Tube:4-digit common anode with a 0.36-inch digital tube with a score point, highlighted …
1080P HDMI Male to 3RCA Audio Video AV Output Transmit Cable Adapter 1.5M/5Feet
$7.86Expansion Board & ShieldAdd to cartFeatures– Gold plated connectors for better signal transfer.– New generic HDMI Male to 3 RCA Audio Video AV Component.– HDMI to RCA cable is designed to connect and transfer signals from HDMI port to RCA port.– High quality HDMI- RCA cable suitable for use in HDTV, Home Theater systems, and all other HDMI to RCA …
1080P HDMI Male to 3RCA Audio Video AV Output Transmit Cable Adapter 1.5M/5FeetRead More
LED Strip Switching Power Supply AC110V-240V to DC12V 60W 5A 160*40*32mm S-60-12
$35.59Power Supply ModuleAdd to cartFeature1. International AC input range2. High efficiency, low working temperature3. Short circuit,overload,over-current protection4. 100% fully load burn-in test5. Built-in EMI filter, low ripple noise6. Low cost, high reliability7. CE and FCC approvalSpecification1. LED switching power supply using pulse width modulation (PWM) switching technology designed to ensure power supply stability and high efficiency. 2. Product interference, …
LED Strip Switching Power Supply AC110V-240V to DC12V 60W 5A 160*40*32mm S-60-12Read More
5pcs TB371 4 Key MCU Keyboard Button Board Compatible UNO MEGA2560 Pro Mini Nano Due for Raspberry Pi Teensy++ Geekcreit for Arduino – products that work with official for Arduino boards
$14.12Other Module BoardAdd to cartSize ConversionInchesCentimetersPlease according to your own measurements to choose your suitable size. The tags inside the items will show in our Asian (Type) size.Description1. 4-button Common Cathode key module(When pressed output low level). 2. GND K1 K2 K3 K4′ 4 PIN OUT 2.54mm3. Working voltage:DC 0-48V 4. Size:12.7 x 33mm5. It can be inserted directly …
TCRT5000 infrared Reflective Switch IR Barrier Line Track Sensor Module
$4.36Sensor & Detector ModuleAdd to cartTCRT5000 Infrared Reflective Switch IR Barrier Line Track Sensor ModuleFeaturesTCRT5000 sensor of infrared emission diode constantly launch infrared, the infrared ray is emitted when the intensity of reflected back has not been reflected or but is not big enough, the light activated triode has been in the off state, the output end of the module …
TCRT5000 infrared Reflective Switch IR Barrier Line Track Sensor ModuleRead More
Reviews
There are no reviews yet.