3Pcs inverter Boost High Voltage Generator 15KV High Frequency Transformer
$18.14
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Use
School science experiment, electronic equipment, negative ion generator, small scientific production and so on.
Feature
This circuit works to produce a stable high-frequency arc, the temperature is extremely high, can easily ignite the combustible, so it was called a plasma lighter.
Note
This transformer high voltage winding in the inner layer, is the segment skeleton wound, low voltage winding in the outer layer, please do not mistaken for this transformer is high voltage winding and low voltage winding the same way.
The transformer has two primary winding, one of the main group is coarse copper wire, a group of fine copper wire for the feedback winding. The secondary output is high voltage.
Transformers in a coarse and a thin winding together two copper wire is positive, respectively, the main winding tail and feedback winding head, connect the power supply positive.
Before soldering the transformer, the soldering part of the enameled wire head of the paint need to gently scraping with blade and then soldering, please note.
Precautions for product use
1. After the successful production, the transformer must be sealed with epoxy resin or insulating wax to be used for a long time. The air-borne work in the air will cause the coil to break through damage due to the lack of air insulation.
2. The input voltage of the kit is 3.7v. That is, a section 18650 battery voltage, if you need to increase the input voltage (maximum increase to 12V), you need to increase the feedback resistor resistance (we default send 120 ohm), otherwise the transistor is easy to burn. Feedback resistance increased to 150Ω ~ 1.5KΩ or so, the resistance should be adjusted from large to small, do not too small, otherwise will burn transistor or transformer, and should not be too large, too much will impact the output or make the transistor work in the non-switch state to make the fever is serious hot.
transformer design for the 15KV maximum output, which is 1.5 cm arc, the higher the output voltage is likely to damage the transformer. For reliable long-term continuous work, it is recommended to use insulating wax or epoxy resin to completely seal it, prohibit no-load working when no sealed.
Specification
Input voltage:3.7V-4.2V
Current
Output voltage
Output current
High pressure two-stage ignition distance
Size is about:27 x 16 x 21mm (Manual measurement, please understand the error)
Package includes
3 x High Voltage Generator Kit
Schematic diagram
In order to prevent the output 2-line distance too far, resulting in no-load, you can solder a pin in the output, and put the end of the needle into the arc, is conducive to the discharge arc, lik the following show
After the success of the production, if the output terminal connected to a high-voltage capacitor and three high voltage rectifier composed of voltage doubling circuit, can produce DC high voltage, can produce anion generator, the wiring diagram is as follows:
Weight | 0.054 kg |
---|
Customers Also Viewed
5Pcs A87 4 Channel Optocoupler Isolation Module High And Low Level Expansion Board
$17.08Other Module BoardAdd to cartDescription 1. Function:Use the low level to control the high level. Such as the use of single-chip 3V or 5V voltage control 9V or 12v voltage. 2. HVCC should not exceed 24V. Output OUT1 / OUT2 / OUT3 / OUT4 output current equal to HVCC / 5.1K, absorption current 500ma. 3. This module uses TLP281 …
5Pcs A87 4 Channel Optocoupler Isolation Module High And Low Level Expansion BoardRead More
3pcs DC 3.3V To 20V 5.8GHz Microwave Radar Sensor intelligent Trigger Sensor Switch Module
$16.24Sensor & Detector ModuleAdd to cartDescriptionIt uses Doppler radar technology, with auto-sensing capabilities to control other product,High sensitivity, sensor distance, reliability, wide angle sensor,Wide supply voltage range and other characteristics. Widely used in lighting situations,anti-theft alarm situations.Features1. microwave sensors using planar antenna and receiving echo.2. The switch is active sensors.3. The sensors emit a high-frequency electromagnetic waves and receives their …
3pcs DC 3.3V To 20V 5.8GHz Microwave Radar Sensor intelligent Trigger Sensor Switch ModuleRead More
24V Air Parking Heater Flame Sensor Igniters Flame Detecter 82306B for Webasto Air top 2000
$70.86Solar CollectorsAdd to cartSpecificationsBrand Name:AutoleaderMaterial:Silicon NitrideOEM:82306BItem weight:11gFeaturesThis product is mainly made of silicon nitride ceramic substrate, with tungsten filament as the heat source, tungsten wire embedded in silicon nitride matrix, via hot-press sintering process to form an organic whole, then through grinding, welding wire, thus made the ignition components.Fitmentfor Webasto Air Top 2000Package Included1x Parking Heater Senser
L293D WiFi Smart Robot Car Motor Driver Expansion Board Dual High Power H Bridge Based on ESP12E
$9.79Expansion Board & ShieldAdd to cartL293D WiFi Smart Robot Car Motor Driver Expansion Board Dual High Power H Bridge Based On ESP12E For Specifications 1. Motor power (VM):4.5 ~ 36V 2. Control power (VIN):4.5V ~ 9V(10V MAX) 3. Provide the shortcut connector (short by VM and VIM), thus can use 4. May use common power source (4.5V~9V) by shorting VM …
220V 1000W Hot Plate Electric Iron Burner Heating Stove Heater Household Laboratory Heating Equipments
$52.64Laboratory Heating EquipmentsAdd to cartSpecificationsType:Electric Stove BurnerPlug Type:EUColor:WhiteVoltage:220VPower:1000WRegulating temperature:5 LevelsMaterial:Stainless Steel + IronSize:14*14*5CM (5.5*5.5*2in)Features– Adopted iron shell, thicken panel, material sturdy and durable to use– Portable single burner with 500 watts of power– Powered by electric, do not need fuel, eco-friendly– Easy-to-use temperature-setting knob for low, medium, or high heat– Provides quick and sustained heat; power indicator light– Single …
Reviews
There are no reviews yet.