3Pcs inverter Boost High Voltage Generator 15KV High Frequency Transformer
$18.14
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Use
School science experiment, electronic equipment, negative ion generator, small scientific production and so on.
Feature
This circuit works to produce a stable high-frequency arc, the temperature is extremely high, can easily ignite the combustible, so it was called a plasma lighter.
Note
This transformer high voltage winding in the inner layer, is the segment skeleton wound, low voltage winding in the outer layer, please do not mistaken for this transformer is high voltage winding and low voltage winding the same way.
The transformer has two primary winding, one of the main group is coarse copper wire, a group of fine copper wire for the feedback winding. The secondary output is high voltage.
Transformers in a coarse and a thin winding together two copper wire is positive, respectively, the main winding tail and feedback winding head, connect the power supply positive.
Before soldering the transformer, the soldering part of the enameled wire head of the paint need to gently scraping with blade and then soldering, please note.
Precautions for product use
1. After the successful production, the transformer must be sealed with epoxy resin or insulating wax to be used for a long time. The air-borne work in the air will cause the coil to break through damage due to the lack of air insulation.
2. The input voltage of the kit is 3.7v. That is, a section 18650 battery voltage, if you need to increase the input voltage (maximum increase to 12V), you need to increase the feedback resistor resistance (we default send 120 ohm), otherwise the transistor is easy to burn. Feedback resistance increased to 150Ω ~ 1.5KΩ or so, the resistance should be adjusted from large to small, do not too small, otherwise will burn transistor or transformer, and should not be too large, too much will impact the output or make the transistor work in the non-switch state to make the fever is serious hot.
transformer design for the 15KV maximum output, which is 1.5 cm arc, the higher the output voltage is likely to damage the transformer. For reliable long-term continuous work, it is recommended to use insulating wax or epoxy resin to completely seal it, prohibit no-load working when no sealed.
Specification
Input voltage:3.7V-4.2V
Current
Output voltage
Output current
High pressure two-stage ignition distance
Size is about:27 x 16 x 21mm (Manual measurement, please understand the error)
Package includes
3 x High Voltage Generator Kit
Schematic diagram
In order to prevent the output 2-line distance too far, resulting in no-load, you can solder a pin in the output, and put the end of the needle into the arc, is conducive to the discharge arc, lik the following show
After the success of the production, if the output terminal connected to a high-voltage capacitor and three high voltage rectifier composed of voltage doubling circuit, can produce DC high voltage, can produce anion generator, the wiring diagram is as follows:
Weight | 0.054 kg |
---|
Customers Also Viewed
K202 Low Power Consumption Fingerprint Control Board Switch Fingerprint Access Control Board DC12V
$17.48Other Module BoardAdd to cart>>>Manual:Click here to openSpecifications·P1:Power supply:DC12V·Output:Relay(Max. current:10A)·Standby current:15uA·Fingerprint capacity:120 pieces·Size:64.4*25.4mm·P2:MX 1.0mm space 6 Pin Fingerprint Module(can connect R502,R502-A,R502-AW,R503)·P3:MX 1.25mm space 6 Pin Fingerprint Module(can connect R300,R301T,R303,R303T,R305,R306,R307,R501)K202 is designed for low power consumption, the power supply is DC12V, the relay time can be adjusted by rotating the button, relay time:0.5-13 seconds.It is very easy to register fingerprint, …
intelligent Voice Recognition Module AC108 Audio Decoding Module 4 Microphones Decoder for Smart Speaker DIY
$28.42Expansion Board & ShieldAdd to cartSize ConversionInchesCentimetersPlease according to your own measurements to choose your suitable size. The tags inside the items will show in our Asian (Type) size.Feature1. Based on RASPBERRY PI 40PIN interface, suitable for RASPBERRY PI series motherboards;2. Support RASPBERRY PI ZERO / ZERO W / 2B / 3B / 3B + / 4 and other development …
GP2Y1010AU0F Dust Sensor Module Dust Particle Concentration PM2.5 Haze Detection
$32.79Sensor & Detector ModuleAdd to cartFeaturesEasy to use:only one AD acquisition pin and one control pin are neededAnalog output:The output voltage is linearly related to the dust concentration in the effective range, with a built-in attenuation circuit, the output voltage does not exceed 1.5VSensitivity:0.5V/(100┢g/m3)Effective range:500┢g/m3Wide power supply range:built-in booster circuit, working voltage range 2.5V to 5.5VLow power consumption:within a sampling …
GP2Y1010AU0F Dust Sensor Module Dust Particle Concentration PM2.5 Haze DetectionRead More
3pcs TM1637 4 Bits Digital LED Display Module 7 Segment 0.36 inch RED Anode Tube 4 Serial Driver Board for
$11.00Display ScreenAdd to cartIntroductionThe module is a 12-pin display module with a 4-point common digital tube (0.36 inch) with a clock point. The driver chip is TM1637. It only needs 2 signal lines to enable the MCU to control the 4-bit 8- Segment digital tube.FeaturesDigital Tube:4-digit common anode with a 0.36-inch digital tube with a score point, highlighted …
1080P HDMI Male to 3RCA Audio Video AV Output Transmit Cable Adapter 1.5M/5Feet
$7.86Expansion Board & ShieldAdd to cartFeatures– Gold plated connectors for better signal transfer.– New generic HDMI Male to 3 RCA Audio Video AV Component.– HDMI to RCA cable is designed to connect and transfer signals from HDMI port to RCA port.– High quality HDMI- RCA cable suitable for use in HDTV, Home Theater systems, and all other HDMI to RCA …
1080P HDMI Male to 3RCA Audio Video AV Output Transmit Cable Adapter 1.5M/5FeetRead More
LED Strip Switching Power Supply AC110V-240V to DC12V 60W 5A 160*40*32mm S-60-12
$35.59Power Supply ModuleAdd to cartFeature1. International AC input range2. High efficiency, low working temperature3. Short circuit,overload,over-current protection4. 100% fully load burn-in test5. Built-in EMI filter, low ripple noise6. Low cost, high reliability7. CE and FCC approvalSpecification1. LED switching power supply using pulse width modulation (PWM) switching technology designed to ensure power supply stability and high efficiency. 2. Product interference, …
LED Strip Switching Power Supply AC110V-240V to DC12V 60W 5A 160*40*32mm S-60-12Read More
5pcs TB371 4 Key MCU Keyboard Button Board Compatible UNO MEGA2560 Pro Mini Nano Due for Raspberry Pi Teensy++ Geekcreit for Arduino – products that work with official for Arduino boards
$14.12Other Module BoardAdd to cartSize ConversionInchesCentimetersPlease according to your own measurements to choose your suitable size. The tags inside the items will show in our Asian (Type) size.Description1. 4-button Common Cathode key module(When pressed output low level). 2. GND K1 K2 K3 K4′ 4 PIN OUT 2.54mm3. Working voltage:DC 0-48V 4. Size:12.7 x 33mm5. It can be inserted directly …
TCRT5000 infrared Reflective Switch IR Barrier Line Track Sensor Module
$4.36Sensor & Detector ModuleAdd to cartTCRT5000 Infrared Reflective Switch IR Barrier Line Track Sensor ModuleFeaturesTCRT5000 sensor of infrared emission diode constantly launch infrared, the infrared ray is emitted when the intensity of reflected back has not been reflected or but is not big enough, the light activated triode has been in the off state, the output end of the module …
TCRT5000 infrared Reflective Switch IR Barrier Line Track Sensor ModuleRead More
Reviews
There are no reviews yet.