10Pcs inverter Boost High Voltage Generator 15KV High Frequency Transformer
$55.49
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Use
School science experiment, electronic equipment, negative ion generator, small scientific production and so on.
Feature
This circuit works to produce a stable high-frequency arc, the temperature is extremely high, can easily ignite the combustible, so it was called a plasma lighter.
Note
This transformer high voltage winding in the inner layer, is the segment skeleton wound, low voltage winding in the outer layer, please do not mistaken for this transformer is high voltage winding and low voltage winding the same way.
The transformer has two primary winding, one of the main group is coarse copper wire, a group of fine copper wire for the feedback winding. The secondary output is high voltage.
Transformers in a coarse and a thin winding together two copper wire is positive, respectively, the main winding tail and feedback winding head, connect the power supply positive.
Before soldering the transformer, the soldering part of the enameled wire head of the paint need to gently scraping with blade and then soldering, please note.
Precautions for product use
1. After the successful production, the transformer must be sealed with epoxy resin or insulating wax to be used for a long time. The air-borne work in the air will cause the coil to break through damage due to the lack of air insulation.
2. The input voltage of the kit is 3.7v. That is, a section 18650 battery voltage, if you need to increase the input voltage (maximum increase to 12V), you need to increase the feedback resistor resistance (we default send 120 ohm), otherwise the transistor is easy to burn. Feedback resistance increased to 150Ω ~ 1.5KΩ or so, the resistance should be adjusted from large to small, do not too small, otherwise will burn transistor or transformer, and should not be too large, too much will impact the output or make the transistor work in the non-switch state to make the fever is serious hot.
transformer design for the 15KV maximum output, which is 1.5 cm arc, the higher the output voltage is likely to damage the transformer. For reliable long-term continuous work, it is recommended to use insulating wax or epoxy resin to completely seal it, prohibit no-load working when no sealed.
Specification
Input voltage:3.7V-4.2V
Current
Output voltage
Output current
High pressure two-stage ignition distance
Size is about:27 x 16 x 21mm (Manual measurement, please understand the error)
Package includes
10 x High Voltage Generator Kit
Schematic diagram
In order to prevent the output 2-line distance too far, resulting in no-load, you can solder a pin in the output, and put the end of the needle into the arc, is conducive to the discharge arc, lik the following show
After the success of the production, if the output terminal connected to a high-voltage capacitor and three high voltage rectifier composed of voltage doubling circuit, can produce DC high voltage, can produce anion generator, the wiring diagram is as follows:
Weight | 0.18 kg |
---|
Customers Also Viewed
Geekwrom HD 3.5 inch TFT Display Shield 800×480 for Raspberry Pi 3B 2B + Acrylic Matching Case Kit
$121.30Raspberry Pi & Orange PiAdd to cartGeekwrom HD 3.5 Inch TFT Display Shield 800×480 For Raspberry Pi 3B 2B + Acrylic Matching Case KitHD 3.5 Inch TFT Display Shield 800×480 For Raspberry Pi 3B 2BFeatures– Demensions:85mm*56.5mm;– Resolution:800 x 480, 3.5 inch;– 267ppi High PPI display screen;– 11ms High Response Time(more than 60 fps);– 160° Wide Viewing Angle;– 900:1 High Contrast Ratio;– …
intelligent Screen Solar Pure Sine Wave Power inverter 1200W-6000W DC To AC 110V 120V Converter
$121.49InvertersAdd to cartWatt 1200W Voltage 12V Type Single digital display / Watt 2200W Voltage 12V Type Single digital display / Watt 3000W Voltage 12V Type Single digital display / Watt 3000W Voltage 24V Type Single digital display / Watt 3000W Voltage 48V Type Single digital displ
500W Aquarium Submersible Stainless Steel Heating Rod Adjustable Heater
$48.59Solar CollectorsAdd to cartDescriptionMaterial:Stainless SteelColor:SilverPlug:US PlugVoltage:220-240V 50HzWattage:500WTemperature range:16-32°CCable Length:120cm/47.24inch(appr.)Heating Rod Length:41cm/16.14inch(appr.)FeaturesMade of stainless steel material, anti-rust, useful and durable.Double insulation & waterproof.Keep the water temperature steady.Suitable for aquarium:500L (for reference only).Simple adjustment and easy to read temperature indicator.Easy to install with 2 strong suckers (mounting distance of 2 suckers is about 9.5cm).Adjustment knob allows you to adjust the …
500W Aquarium Submersible Stainless Steel Heating Rod Adjustable HeaterRead More
5pcs JoyStick Module Shield 2.54mm 5 pin Biaxial Buttons Rocker for PS2 Joystick Game Controller Sensor
$14.30Other Module BoardAdd to cartFeaturejoystick joysticks standard interface module electronic building blocks and 2.54mm pin interface leads.Phillips is a two-way rocker 10K resistor, with the joystick in a different direction, tap the resistance vary. This module uses a 5V supply, the original state X, Y readout voltage of 2.5V or so, when pressed with the direction of the arrow, …
4Pcs Geekcreit Ultrasonic Module HC-SR04 Distance Measuring Ranging Transducers Sensor DC 5V 2-450cm
$9.83Sensor & Detector ModuleAdd to cartDescriptionWorking Voltage:5V(DC)Static Current:Less than 2mA.Output Signal:Electric frequency signal, high level 5V, low level 0V.Sensor Angle:Not more than 15 degrees.Detection Distance:2cm-450cm.High Precision:Up to 0.3cmInput Trigger Signal:10us TTL impulseSignal:output TTL PWL signalMode of connectionVCCtrig(T)ech0(R)GNDUse MethodSupply module with 5V, the output will be 5V while obstacle in range, or 0V if not.The out pin of this module is …
1MHz-700MHZ 3.2W HF VHF UHF FM Transmitter RF Power Amplifier for Ham Radio
$50.29RF amplifierAdd to cartApplicationBroadband RF power amplifier for all types of wireless applications, FM shortwave radios remote control toys, digital radio, etc., enter 1 milliwatt (0DBM) maximum output of 3 watts, 15V voltage supply, broadband work 1MHZ to 700MHZ can be work. As a result of well-designed, low end that can reach 35DBM (3W), at 500M, the output …
1MHz-700MHZ 3.2W HF VHF UHF FM Transmitter RF Power Amplifier for Ham RadioRead More
Reviews
There are no reviews yet.