24V 36V 48V 60V BMS 6-20S 50A 80A 120A 150A 3.7V Li-ion Battery Protection Board with Temperature Control Separate Port Version
$61.22
Current 50A / Current 80A / Current 120A /
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Tips
1. The current of the selected protection board is different, the number or model of the MOS tube on the board is different, the actual product shall prevail
2. For batteries with different numbers of strings, you only need to short-circuit the cable from B+ to the number of strings you need.
3. Do not insert the flat wire into the terminal before connecting the protection board, remember! Wrong cable connection will burn the protection board!
4. Connect the ribbon cable and the battery in order, check that the adjacent voltage is correct, and then insert the ribbon cable; then use a short and thick wire to connect to B-, and then to C-(P-).
5. Please install the protection board close to the negative pole of the battery. The wire connecting B- should be as short and thick as possible, and the length should be controlled within 10cm. It is recommended that the 50A version use 4 square wires and the 80A version use 6 square wires. The B- connection is too long or too thin will cause a series of problems such as failure to start, power failure during operation and so on.
Features
The board adopts mature protection circuit, original dedicated protection IC, 100A high current low internal resistance MOS (single MOS internal resistance as low as 4.2 milliohms), with perfect and stable charging and discharging protection functions.
Small size and large current can be used in large current occasions such as electric tools, electric vehicles, UPS, etc.
Electric vehicle type:Motor wattage:Recommended protection board
Two-wheel electric vehicle:500-800W:50A
800-1000W:80A
>1000W:120A
Three-wheeled electric vehicle:ordinary:800-1000W:80A
>1000W:120A
Cargo:120A/150A
Four-wheel electric vehicle:120A/150A
Package Included
1x BMS 6-20S 50A 80A 120A 150A 3.7V Li-ion Battery Protection Board Separate Port Version
Weight | 0.12 kg |
---|
Customers Also Viewed
DC12V 0.02-0.8MPa Solenoid Valve for Solar Water Heater
$21.87Laboratory Heating EquipmentsAdd to cartDC12V 0.02-0.8MPa Solenoid Valve for Solar Water HeaterSpecificationsModel:SSG-2Type:Normally ClosedMaterials:Plastic & CopperDimension:83*90*49cmPipe Inside Diameter:1/2 inchNet Weight:(approx.) 190gFeaturesThis is a DC12V solenoid valve usually used for solar water heater.It can work with water from 1 to 100℃ (or some other liquid).Working Voltage Range:Rated Voltage ±10%Working Water Pressure:0.02 to 0.8MpaThe working water pressure would be too low/high to …
DC12V 0.02-0.8MPa Solenoid Valve for Solar Water HeaterRead More
650 Pcs Assorted Ring insulated Electrical Wire Terminals Crimp Connector Set Kit
$76.17Terminal BlocksAdd to cartDescription650 Pcs Assorted Ring Insulated Electrical Wire Terminals Crimp Connector Set KitSpecificationQuantity:650PcsMaterial:Copper + PVC+ TinplateInsulated crimp terminals.All are enclosed in plastic case for easy access.The assorted crimp terminals is including50 x Ring M3 Red50 x Ring M4 Red50 x Ring M5 Red50 x Ring M6 Red50 x Ring M8 Red50 x Ring M4 Blue50 x …
650 Pcs Assorted Ring insulated Electrical Wire Terminals Crimp Connector Set KitRead More
3.5 inch Protective Enclosure Case Support Dispaly Screen or Cooling Fan for Raspberry Pi
$9.26Raspberry Pi & Orange PiAdd to cartFeatures– Fully updated for Raspberry Pi 3B+/3B/2B– Can support 3.5 inch screen or cooling fan (notes:can not assemble them at the same time)– Heat sink openings for both CPU and LAN chip– High-gloss finish, surface mountableSpecificationsColor:BlackMaterial:ABSSuitable for Raspberry Pi 3B+/3B/2BWeight:45gSize:9cm*6.2cm*3.4cmPackage Included1x ABS Case4x Non-slip mat4x Screws
20pcs 0.56 inch Digital Tube DIY Kit TM1650 4-digit LED Digital Tube Display Module for
$47.25DIY Electronic KitsAdd to cartDescription1. Use TM1650 (compatible with AIP650) digital tube driver chip, support 8-level brightness adjustment, working voltage 3.3V ~ 5.5V2. IIC interface, only need 2 ordinary IO can drive, do not need to repeat scanning of MCU, saving MCU resources.3. 4 digit 0.56 inch red common negative digital tube with decimal point.4. 0.56 inch with four …
20pcs 0.56 inch Digital Tube DIY Kit TM1650 4-digit LED Digital Tube Display Module forRead More
WEAH-81 Car Heavy Bass Frequency Divider High and Low 2-way 2 Bass Crossover Upgrade Tool
$33.09Amplifier BoardAdd to cartFeatureBrand:WEAHModel:81Power:100WApplicable impedance:4-8ohmFrequency response:100Hz ~ 45HzDimensions:133 x 95 x 44mmApplication environment:Car or home speaker DIYPackage includes1 x Bass Frequency DividerHow to Wire:
5pcs 8-36W intelligent Sensor LED Ceiling Light And Sound Control Power Supply Module Bulb Panel Light Built-in Power Driver
$21.42Power Supply ModuleAdd to cartDescriptionInput Voltage:AC185-265VOutput Current:0.22AOutput Voltage:24-108VEfficiency:90%Working Frequency:50/60HZOutput Power:8-24WSound Control:50-75dBLight control:7-20LuxDiameter:25.8mmFeature1. The combination of sound and light control, when the light is strong, does not work, the light intensity is lower than 12-15LUX, and the sound of the induction 27-36DB starts automatically.2. Delay 40-60S automatically extinguished, easy to install, compatible with ordinary switches, no additional wiring.3. Single trigger, …
Reviews
There are no reviews yet.