3pcs HC-SR501 Adjustable infrared IR Pyroelectric PIR Module Motion Sensor Human Body induction Detector
$8.65
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Features
1. Automatic induction:When someone enters its induction limits, enter the high level, people leave the sensor range is automatically delayed off high. Output low.
2. photosensitive control (optional):the module reserved for location, can be set to photosensitive control, strong light during the day or not induction. Photosensitive control is optional, the factory did not install the photosensitive resistor. If necessary, please buy a separate photosensitive resistor to install.
3. Two trigger modes:L is not repeatable, H is repeatable. Can be jumper selected, the default is H.
A. non-repeatable trigger mode:the induction output high, the delay time is over, the output will automatically change from high to low.
B. Repeated trigger mode:that is, after sensing the output high, in the delay time period, if the human body in its sensing limits of activities, its output will remain high until the delay after the person will leave the high The level changes to low level (the sensing module automatically delays a delay time after every activity of the human body, and takes the time of the last activity as the starting point of the delay time).
4. Induction blocking time (default setting:3-4 seconds):After each sensing output (high level goes low), the sensing module can be followed by a blocking time, during which it is sensed The device does not receive any sense signals. This function can be used to achieve the interval between the sensing output time and the blocking time. It can be applied to the interval detection products. At the same time, this function can effectively suppress all kinds of interference in the process of load switching.
5. Wide operating voltage:the default operating voltage DC5V to 20V.
6. Micro-power:Quiescent current 65 microamps, especially for dry battery-powered electrical products.
7. Output high-level signal:can be easily with various types of circuits to achieve docking.
Instructions for use
1. Induction module power about one minute after the initialization time, at this time the module will output 0-3 times a minute, a minute into the standby state.
2. Light and other interference should be avoided Directly close the surface of the lens module, so as not to introduce interference with the signal to produce malfunction; use of the environment as far as possible to avoid
Free flow of wind, the wind will cause interference to the sensor.
3. Sensor module with dual-element probe, the probe window is rectangular, dual element (A yuan B yuan) in the longer direction at both ends, when the body from left to right
Or from right to left through the infrared spectrum to the dual time, distance difference, the greater the difference, the more sensitive induction, when the body from the front to the probe
Head or from top to bottom or from bottom to top direction, the dual element can not detect infrared spectral distance changes, no difference, so the sensor insensitive or does not work; so the sensor should be installed so that the direction of the probe dual And the direction of human activity as much as possible parallel to ensure that the body has been through
Probe dual-element induction. In order to increase the sensing angle limits, this module uses a circular lens, also makes the probe four sides are sensitive, but the left and right sides are still
However, compared with the upper and lower direction of the two induction limits, sensitivity, installation must still try to according to the above requirements.
Use should pay attention to the following points
1. The DC voltage must meet our requirements, too high and too low will affect the performance of the module, but also requires the power supply must be a good regulator filter, such as computer USB power, mobile phone charger power supply, the old 9V stacked battery Are unable to meet the module work requirements, it is recommended that customers use the power transformer and the regulator through the three-terminal voltage regulator and then through the 220UF and 0.1UF capacitor filter power supply.
2. Although the human body is not in front of the module, but the human body from the module is too close to the module can also be caused by the sensor output, as well as debugging the human body do not touch the circuit part will also affect the module work , A more scientific approach is to output a LED or a multimeter, the module covered with a newspaper, when someone leaves room, wait 2 minutes and see if the module still has output.
3. The module does not take the load to work properly, connected to the load after the work of chaos, one reason is because the power capacity is very small load power consumption, load caused by voltage fluctuations caused by the module malfunction, the other reason is the load The power will have interference in the work, such as relays or electromagnets and another inductive load will produce a reverse electromotive force, 315M emission plate will have electromagnetic radiation and other work will affect the module. The solution is as follows:A, the power part of the inductor filter. B, using the load and the module using different voltage methods, such as:load using 24V operating voltage, the module uses 12V operating voltage, during which the use of three-terminal regulator isolation. C:Use a larger capacity power supply.
4. The human body sensor module can only work indoors and the work environment should avoid the sun, a strong direct light exposure, if the work environment has a strong RF interference, you can use shielding measures. In case of strong air interference, close the doors and windows or prevent convection. The induction area to avoid facing heating appliances and objects as well as easy to wind debris and clothing.
5. The human body sensor module is recommended to install in a sealed box, otherwise, there may have been the output signal.
6. If the body sensor module detection angle is less than 90 degrees, you can use opaque adhesive tape to cut off the lens or cut lens to achieve.
7. The human body sensor module with dual-element probe, the body’s hands and feet and head movement direction and the sensitivity of the sensor are closely linked, and the infrared module determines the characteristics of the sensor can not accurately control the distance.
8. The module of the probe (PIR) can be mounted on the other side of the circuit board. The probe can also be extended with a two-core shielded cable, the length should be less than 20 cm as well.
Package includes
3 x HC-SR501 Motion Sensor
Weight | 0.027 kg |
---|
Customers Also Viewed
HS-48B Set 600PCs Cold-pressed Assorted Crimp Terminal Para Fio Combination Plug Spring Boxed Connector Cross Wire Crimping Tool
$18.21Electronic Accessories & SuppliesAdd to cartPackage Included6.3mm:0.75-1.5mm2 / AWG 20-16;50 pieces male and 50 pieces female50 pieces each protective cover for male and female4.8mm:0.75-1.5mm2 / AWG 20-16;50 pieces male and 50 pieces female50 pieces each protective cover for male and female2.8mm:0.5 – 1.0 mm2 / AWG 22-18;50 pieces male and 50 pieces female50 pieces each protective cover for male and …
Geekcreit 315/433MHz DC12V 10A 1CH Single Channel Wireless Relay RF Switch Receiver Board with Case
$17.48Relay ModuleAdd to cartSpecification1. Input Voltage:DC10-14V2. Standby Current3. RF Frequency:315/433MHz (optional)4. RF Working mode:Super heterodyne receiver5. Receiver Sensitivity:>97dBm6. Remote Control Distance:>100 meter(In open environment)7. Decoding Way:MCU Software decoding8. Can store the number of remote control:509. Support remote control type:Fixed code, learning code10. Channel:1CH11. Multiple working modes:(Jog/Non-Latched ,inter-lock/Latched ,self-lock /Self-Latched,Delay off)12. Wiring Method:Fixed wiring terminal13. Working Voltage:DC12V14. Output Current:10A15. …
OPEN-SMART DC Jack Power 7~12V to DC5V/3.3V Step Down Converter Voltage Regulator Power Supply Module for Breadboad
$6.55Power Supply ModuleAdd to cartDescriptionThis is a mini LDO step-down power module based on AMS1117-5.0 and AMS1117-3.3, and it output fixed 5V / 3.3V.It is a small size, lightweight, especially for model airplanes, smart cars, DIY and other items, PCB experiment board project design, breadboard project design.Features– Module type:LDO step-down module;– Onboard 500mA resettable fuse to protect the power …
offline Version 1610 PRO 3 Axis CNC Router GRBL Control DIY Adjustable Speed Spindle Laser Motor Wood Engraving Milling Machine
$346.06Laser Engraving MachineAdd to cartThe software and instruction please:https://drive.google.com/openid=1JXQbBj-CuYee53yvQESx5HsVRhJ59VTDSpecification:Rated Voltage:24VEngraving area:16x10x4.5cmSpindle:775 spindle motorSoftwear:GRBL control systemssupport system:24V 5.6A adapterStepper motor:fuselage length 34MM,Current 1.33A, 12v.Torque 0.25N/MSpindle:775 spindle motor (12-36V) 24V:10000r / minSupported System:Windows XP / Win 7 / Win 8 / Win 10 / Linux.Drill bits:tip 0.1mm ,20 degree , diameter3.175mm. the package include 10pc.clamps:4 pcs, Hold the thickness of 0-30mm,size:50 …
3Pcs NE555 Pulse Frequency Duty Cycle Adjustable Module Square Wave Signal Generator
$8.13Test & Measuring ModuleAdd to cart3Pcs NE555 Pulse Frequency Duty Cycle Adjustable Module Square Wave Signal GeneratorFeatures1. As a square wave signal generator,generates a square wave signal used for experimental development.2. Used to drive a stepper motor for generating a square wave drive signal.3. Generate adjustable pulse for MCU.4. Generate adjustable pulse,to control circuitry associated.5. Size:31mm x 22mm6. Main chip:NE5557. …
3Pcs NE555 Pulse Frequency Duty Cycle Adjustable Module Square Wave Signal GeneratorRead More
PiFi HIFI DAC+ Digital Audio Card Pinboard for Raspberry Pi 3 Model B /2B/B+/A+
$40.49Raspberry Pi & Orange PiAdd to cartPiFi HIFI DAC+ Digital Audio Card Pinboard For Raspberry Pi 2 Model B / B+ / A+DescripionIt’s suitable for Raspberry pi B+. You can setup a open music player by Volumio systemPackage included1 x Digital Audio Card Pinboard
12V 20W 45CM x 35CM PolyCrystalline Solar Panel with Alligator Clip Wire
$123.28Smart Robot & Solar PanelAdd to cart12V 20W 45CM x 35CM PolyCrystalline Solar Panel With Alligator Clip WireFeatures20W 12V PolyCrystalline Cells Solar Panel High efficiency and excellent performanceProvided with 2 alligator clips and 4m cableSuitable for a variety of equipments, emergency lights, advertising lights, traffic lights, electric fans, solar water pumps, motorbike, boat, etc..Power:20WVoltage:12VMaterial:PolyCrystalline Weight:415g Dimensions:45cm x 35cm (LxW)Cable Length:Approx. 4mPackage …
12V 20W 45CM x 35CM PolyCrystalline Solar Panel with Alligator Clip WireRead More
CJMCU-231 Pedometer Sensor Module Triaxial Accelerometer KX023-1025 FIFO FILO
$9.68Sensor & Detector ModuleAdd to cartInstructions:http://files.hobbyant.com/2018/06/CJMCU-23-TEST.zipChip FeatureDigital High-Pass Filter OutputsEmbedded FIFO/FILO bufferLow Power Consumption with FlexSet™ Performance OptimizationInternal voltage regulatorEnhanced integrated Directional Tap/Double-TapTM, and Device-orientation AlgorithmsUser-configurable wake-up functionDigital I2C up to 3.4 MHzDigital 3-wire and 4-wire SPI up to 10 MHzLead-free SolderabilityExcellent Temperature PerformanceHigh Shock SurvivabilityFactory Programmed Offset and SensitivitySelf-test FunctionPackage includes1 x Pedometer Sensor Module
Reviews
There are no reviews yet.