20pcs Electronic DIY LED Dimming Lights Series and Parallel Circuit Technology Small Production Kit
$54.99
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Description
The purpose of the experiment
1. Understand and recognize the light-emitting diodes and illuminate the light-emitting diodes (LEDs);
2. Understand the role of understanding resistance, series and parallel resistance;
3. Understand the self-locking switch;
4. Understand and recognize adjustable resistors and use adjustable resistors;
Experimental steps
Step 1:The long leg of the light-emitting diode (LED) is the positive pole, and the short leg is the negative pole. First, the long wire of the LED is connected to the black wire (negative electrode) of the battery case, and the short leg of the LED is connected to the red wire (positive electrode) of the battery case. At this time, the light emitting diode (LED) is not lit. Then send it over again, let the long leg of the LED connect to the red line of the battery box, and the short leg of the LED is connected to the black line of the battery box. At this time, the LED lights up, indicating that the LED is in one-way operation and the single-pass characteristic of the diode .
Step 2:In the circuit of the experimental step 1, a resistor of 220 ohms is inserted in series, and the brightness of the LED lamp is lowered, and the resistance hinders the current.
Step 3:Connect a 220 ohm resistor in parallel with the resistance in the circuit of the experimental board 2. The brightness of the LED is increased, indicating that the total resistance of the resistor in the circuit is reduced after the resistors are connected in parallel.
Step 4:Change the two resistors of the experimental step 3 from parallel to series. After the series connection, the brightness of the LED lamp is the lowest. After the series connection of the resistors, the total resistance of the resistor in the circuit increases.
Step 5:Replace the original resistor with a potentiometer. The potentiometer has 3 feet, and the resistance of pins 1 and 3 is fixed. The resistance of pins 1 and 2, 2 feet and 3 feet can be changed by adjusting the potentiometer knob. When experimenting, you can pick up 2 of them. The foot has to experiment many times, adjust the potentiometer knob to observe the change of LED brightness, so that you can fully understand the potentiometer.
Step 6:Know the self-locking. Press and wait for the light to be on, then press the light to turn off.
Package included
20 x DIY LED Dimming Lights Technology Small Production Kit
Weight | 0.54 kg |
---|
Customers Also Viewed
3 Axis GRBL USB Driver offline Controller Control Module LCD Screen w/ Controller Board SD Card for CNC 1610 2418 3018 Wood Router Laser Engraving Machine
$93.14Control BoardAdd to cartDescriptionThis offline controller w/ controller board is designed for the use of Mini CNC router 1610/2418/3018 and even with more advanced function of tool set, limit switch supportive, Laser supportive; Offline and Bluetooth supportive.SpecificationUSB Cable Length:20cmFirmware:GRBL 08, 09, 1.1 and so on Input Voltage:DC 7V- 36VApplicable CNC Router:3 Axis CNC router 1610; 2418; 3018Features1. Support …
20Pcs PS2 Game Joystick Switch Sensor Module
$34.87Other Module BoardAdd to cart20Pcs PS2 Game Joystick Module For Description This is PS2 game joystick module for Lots of robot projects need joystick. This module provides a affordable solution to that. Simply connect to two analog inputs, the robot is at your commands with X,Y control. It also has a switch that is connected to a digital pin. …
Ebyte E07-M1101D-TH 10dBm Spring Antenna 433MHz CC1101 Wireless Transceiver SPI 433mhz RF Module
$9.18Smart ModuleAdd to cartSpecificationsInterface:SPIPower:10dBmDistance:520mSupply voltage:1.9 ~ 3.6V DCFrequency:433MHz(387 ~ 464MHz)RF Parameter:Value:RemarkWorking frequency:387~464 MHz:Default:433MHz (26MHz oscillator)Transmitting power:10 dBm:Max. Power (10mW)Receiving sensitivity:-108 dBm:Air data rate:0.6kbpsAir data rate:0.6k~500kbps:Default:0.6kbpsTest distance:600m:In open and clear air, with maximum power, 5dBi antenna gain, height of 2m, air data rate:0.6kbpsHardware Parameter:Value:RemarkSize15 * 30 mm Without Spring antennaAntenna typeSpring antenna Communication interfaceSPI PackageDIP Electronic parameter:Min.:Typ.:Max.:Unit:ConditionPower supply:1.8:3.3:3.6:VCommunication level:1.8:3.3:3.6:VTransmitting …
Waveshare IS62WV51216BLL SRAM RAM Module Storage Memory Board
$28.42Expansion Board & ShieldAdd to cartFeatureFunction:SRAM IS62WV51216BLL (8M Bit), can be directly connected to the corresponding FSMC interface of the Open series development board, and the external expansion interface supports external expansion of SRAM, LAN, USB HOST, etc.Typical application:SRAM external expansion storageMain resources:IS62WV51216BLL (8M Bit), control interfacePackage includes1 x IS62WV51216BLL SRAM Board
3 Megapixel Optical Zoom Cam Module Fixed Focus 3MP OV3660 Camera Module FOV 79
$15.30Other Module BoardAdd to cart>>>Manual:Click here to openSpecificationsModel No.:HBVCAM-3M1917Model Size:30mm ≠ 25mm ≠ 5.0mm÷0.2MMTemperature (Operation):-30C to 70CTemperature (Stable Image):0C to 50CAssembly technique:SMT (ROSH)Focus:FixedObject distance:30CM-infinityResolution:800LW/PH (Center)PCB printing ink:Blackinterface:USB 2.0Power supply:USB bus powersupply voltage:DC 5V÷5%Maximum Power consumption:600WOperating system request:Win XP/win 7,8 / vista /android 4.0/ mac /Linuxwith uvc Sensor:OV3660 (1/5” )Seneor Package:CSP,Bare DieMaximum resolution:2048*1536Sensitivity:670mV /(lux-sec)Pixel Size:1.4┢m x 1.4┢m Maximum Image Transfer …
3 Megapixel Optical Zoom Cam Module Fixed Focus 3MP OV3660 Camera Module FOV 79Read More
Hall Effect Magnetic Sensor Module DC 5V
$4.36Sensor & Detector ModuleAdd to cartDescription This is Hall Effect magnetic sensor module DC 5V for Brand:KEYES Model:KY-003 Magnetic, speed, gap induction Suitable for DIY project Working voltage:DC 5V Material:PCB Feature Small size and high sensitivity. response temperature and good performance. Precision and high reliability 3144 Series Hall principle of Hall effect switch IC, using technology to produce magnetic semiconductor …
Geekcreit Portable Mini Automatic Spot Welding Machine Control Board 12V/5.6V Portable Lithium Battery Spot Welding Circuit Board Accessories
$40.49Driver ModuleAdd to cartInstructions for use of automatic spot welding control board1. Power requirements:In 12V mode, voltage input is 7-15V (12V recommended), in 5.6V capacitor mode, voltage supports 3.7-6V (recommended 5.6V), current requirements:can output actual current 120-360A2. Button function:switch between 1 power level-2 power level-3 power level-4 power level after long press for 3 seconds3. The red light …
Reviews
There are no reviews yet.