10pcs Electronic DIY LED Dimming Lights Series and Parallel Circuit Technology Small Production Kit
$29.32
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Description
The purpose of the experiment
1. Understand and recognize the light-emitting diodes and illuminate the light-emitting diodes (LEDs);
2. Understand the role of understanding resistance, series and parallel resistance;
3. Understand the self-locking switch;
4. Understand and recognize adjustable resistors and use adjustable resistors;
Experimental steps
Step 1:The long leg of the light-emitting diode (LED) is the positive pole, and the short leg is the negative pole. First, the long wire of the LED is connected to the black wire (negative electrode) of the battery case, and the short leg of the LED is connected to the red wire (positive electrode) of the battery case. At this time, the light emitting diode (LED) is not lit. Then send it over again, let the long leg of the LED connect to the red line of the battery box, and the short leg of the LED is connected to the black line of the battery box. At this time, the LED lights up, indicating that the LED is in one-way operation and the single-pass characteristic of the diode .
Step 2:In the circuit of the experimental step 1, a resistor of 220 ohms is inserted in series, and the brightness of the LED lamp is lowered, and the resistance hinders the current.
Step 3:Connect a 220 ohm resistor in parallel with the resistance in the circuit of the experimental board 2. The brightness of the LED is increased, indicating that the total resistance of the resistor in the circuit is reduced after the resistors are connected in parallel.
Step 4:Change the two resistors of the experimental step 3 from parallel to series. After the series connection, the brightness of the LED lamp is the lowest. After the series connection of the resistors, the total resistance of the resistor in the circuit increases.
Step 5:Replace the original resistor with a potentiometer. The potentiometer has 3 feet, and the resistance of pins 1 and 3 is fixed. The resistance of pins 1 and 2, 2 feet and 3 feet can be changed by adjusting the potentiometer knob. When experimenting, you can pick up 2 of them. The foot has to experiment many times, adjust the potentiometer knob to observe the change of LED brightness, so that you can fully understand the potentiometer.
Step 6:Know the self-locking. Press and wait for the light to be on, then press the light to turn off.
Package included
10 x DIY LED Dimming Lights Technology Small Production Kit
Weight | 0.27 kg |
---|
Customers Also Viewed
3Pcs MPR121-Breakout-v12 Proximity Capacitive Touch Sensor Controller Keyboard Development Board
$16.16Motherboard & Development BoardAdd to cartDescriptionThis is a breakout board for Freescale’s MPR121QR2. The MPR121 is a capacitive touch sensor controller driven by an I2C interface.The chip can control up to twelve individual electrodes, as well as a simulated thirteenth electrode. The MPR121 also features eight LED driving pins. When these pins are not configured as electrodes, they may be …
220V 100A Class A Power Amplifier Soft Start Delay Temperature Protection Board with Gas Discharge Tube
$24.95Relay ModuleAdd to cartFeatures100% Brand new and high quality.FunctionThe board is equipped with a gas discharge tube. The gas discharge tube is composed of a pair of cold cathode plates which are separated from each other and enclosed in a ceramic tube filled with a certain inert gas (Ar).The gas discharge tube is turned off under normal operating …
Excellway Terminals 40 Pcs 2p 3p 4p 5pin Right angle JST-XH Male Female Lipo Balance Connector
$36.44ConnectorsAdd to cartSpecificaiton Brand:Excellway Pitch:2.54mm Current Rating:1A AC, DC Voltage Rating:125V AC, DC Temperature Range:-25 deg C ~ +85 deg C Insulation Resistance:100M Omega Min. Wire Range:AWG 24~ 32 Insulation O.D.:1.00mm ( Max.) Withstanding Voltage:500V AC/minute Features These work great with all your typical and breadboard style pin connectors and sockets. This kit comes with the most …
HBV-1466FF Fixed Focus 5MP OV5640 FPC Camera Module USB 5 Million Pixels IP Camera Module
$42.85Other Module BoardAdd to cartSpecificationsModel No.:HBVCAM-1466FFModel Size:68.2mm ≠ 26mm ≠ 6mm÷0.2MMTemperature (Operation):-30C to 70CTemperature (Stable Image):0C to 50CAssembly technique:SMT (ROSH)Focus:FixedObject distance:30CM-infinitResolution:800LW/PH (Center)Interface:USB 2.0Power:USB bus powerMaximum Power consumption:940 mWPackage:Anti-electrostatic trayOperating system request:Win XP/win 7,8 / vista /android 4.0/ mac /Linuxwith uvcCertifications:FCC and CEActive Array Size:2592*1944Sensor:OV5640 (1/4” )Sensitivity:600mv /(lux-sec)Pixel Size:1.4┢m x1.4┢mMaximum Image Transfer Rate:MJPEG 1024×768 30FPS / YUY2 160×120 30FPSMJPEG 1280×720 …
HBV-1466FF Fixed Focus 5MP OV5640 FPC Camera Module USB 5 Million Pixels IP Camera ModuleRead More
10pcs 40x40mm Small Fan 4010S Computer Chassis CPU Fan 2 Line with Plug
$19.84Electronic Accessories & SuppliesAdd to cartDescriptionAppearance size:40mm x 40mm x 10mmSpeed reference:4000 ± 10% RPMNoise Reference:18DBAir volume reference:18.17-25.97CFMRated voltage:12VRated current:0.10APackage included10 x Fan
Reviews
There are no reviews yet.