DIY Airband Radio Receiver Aviation Band Receiver Kit
$43.73
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Description
Like many scanner enthusiasts and ham operators, you are interested in listening in on all the excitement manifest in aeronautic communication, but lack the equipment to pursue your interest, then maybe the Aviation-Band Receiver described in this article is for you.
The Aviation Receiver, designed to tune the 118-135MHz band, features exceptional sensitivity, image rejection, signal-to-noise ratio, and stability.
The receiver is ideally suited to listening in on ground and air communication associated with commercial airlines and general aviation.
Powered from a 9-volt alkaline battery, it can be taken along with your to local airports so that you won’t miss a moment of the action.
And even if you’re nowhere near an airport, this little receiver will pick-up all the ground-to-air and vice-versa communications of any plane or ground facility within about 130 miles (190Km).
Color:Green
Material:CCL
Construction
Once you have obtained all of the components and the board for the Aviation Receiver, construction can begin. A parts-placement diagram is shown in Fig. When assembling the project, take special care that polarity-sensitive components (electrolytic capacitors [keep leads as short as possible], diodes, and transistors) are installed properly. Just one part installed backwards can cause grievous harm!
Inductors (Aircoils) L1,L3,L5 can be made easily on a 5mm drill bit. Before you wind them, scrape the enamel of each end, about 5mm. Then wind the 1.5 turn (2-turns is okay too). I know it can be tricky especially if you have big fingers like me. Begin by installing the passive components (6 jumper wires, sockets, resistors, capacitors, inductors). Followed by installing the active components; diodes, transistors, and IC’s. Once the active components have been installed, check your work for the usual construction errors; cold solder joints, misplaced or reversed-lead components, solder bridges, etc. Once you have determined that he circuit has been correctly assembled, it’s time to consider the enclosure that will house the receiver.
The receiver’s circuit board can be housed in any enclosure that you choose.
Note
Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1-3cm.
Package included
1 x DIY KITs Airband Radio Receiver Aviation Band Receiver
1 x English manual
Weight | 0.081 kg |
---|
Customers Also Viewed
5Pcs A87 4 Channel Optocoupler Isolation Module High And Low Level Expansion Board
$17.08Other Module BoardAdd to cartDescription 1. Function:Use the low level to control the high level. Such as the use of single-chip 3V or 5V voltage control 9V or 12v voltage. 2. HVCC should not exceed 24V. Output OUT1 / OUT2 / OUT3 / OUT4 output current equal to HVCC / 5.1K, absorption current 500ma. 3. This module uses TLP281 …
5Pcs A87 4 Channel Optocoupler Isolation Module High And Low Level Expansion BoardRead More
3pcs DC 3.3V To 20V 5.8GHz Microwave Radar Sensor intelligent Trigger Sensor Switch Module
$16.24Sensor & Detector ModuleAdd to cartDescriptionIt uses Doppler radar technology, with auto-sensing capabilities to control other product,High sensitivity, sensor distance, reliability, wide angle sensor,Wide supply voltage range and other characteristics. Widely used in lighting situations,anti-theft alarm situations.Features1. microwave sensors using planar antenna and receiving echo.2. The switch is active sensors.3. The sensors emit a high-frequency electromagnetic waves and receives their …
3pcs DC 3.3V To 20V 5.8GHz Microwave Radar Sensor intelligent Trigger Sensor Switch ModuleRead More
24V Air Parking Heater Flame Sensor Igniters Flame Detecter 82306B for Webasto Air top 2000
$70.86Solar CollectorsAdd to cartSpecificationsBrand Name:AutoleaderMaterial:Silicon NitrideOEM:82306BItem weight:11gFeaturesThis product is mainly made of silicon nitride ceramic substrate, with tungsten filament as the heat source, tungsten wire embedded in silicon nitride matrix, via hot-press sintering process to form an organic whole, then through grinding, welding wire, thus made the ignition components.Fitmentfor Webasto Air Top 2000Package Included1x Parking Heater Senser
L293D WiFi Smart Robot Car Motor Driver Expansion Board Dual High Power H Bridge Based on ESP12E
$9.79Expansion Board & ShieldAdd to cartL293D WiFi Smart Robot Car Motor Driver Expansion Board Dual High Power H Bridge Based On ESP12E For Specifications 1. Motor power (VM):4.5 ~ 36V 2. Control power (VIN):4.5V ~ 9V(10V MAX) 3. Provide the shortcut connector (short by VM and VIM), thus can use 4. May use common power source (4.5V~9V) by shorting VM …
220V 1000W Hot Plate Electric Iron Burner Heating Stove Heater Household Laboratory Heating Equipments
$52.64Laboratory Heating EquipmentsAdd to cartSpecificationsType:Electric Stove BurnerPlug Type:EUColor:WhiteVoltage:220VPower:1000WRegulating temperature:5 LevelsMaterial:Stainless Steel + IronSize:14*14*5CM (5.5*5.5*2in)Features– Adopted iron shell, thicken panel, material sturdy and durable to use– Portable single burner with 500 watts of power– Powered by electric, do not need fuel, eco-friendly– Easy-to-use temperature-setting knob for low, medium, or high heat– Provides quick and sustained heat; power indicator light– Single …
Reviews
There are no reviews yet.